NZQA Expiring unit standard
16100 version 4
Page 1 of 3
Title
Repair minor non-stretched panel damage and metal finish the repair
in the motor body industry
Level
2
Credits
4
Purpose
This unit standard is for people who are at pre- employment
level or who have just started work in the motor body industry.
People credited with this unit standard are able to under
supervision: demonstrate knowledge of hand tools used to
remove a minor dent and of metal finishing in the motor body
industry; prepare to repair minor panel damage in the motor
body industry; and repair minor panel damage in the motor
body industry.
Classification
Motor Industry > Vehicle Bodywork
Available grade
Achieved
Explanatory notes
1
The following legislation and regulations (and subsequent amendments) are relevant
to this unit standard and must be followed where applicable:
– Health and Safety in Employment Act, 1992.
2
Company policy includes workplace standards, practices, and procedures, which
must comply with current legislation requirements. It is assumed the policy also
meets product manufacturers' specifications, recommendations, and standards.
Outcomes and evidence requirements
Outcome 1
Demonstrate knowledge of hand tools used to remove a minor dent, and of metal finishing
in the motor body industry.
Evidence requirements
1.1
Purpose and operation of each hand tool are identified according to the
manufacturer‘s specifications and company policy.
Range
1.2
hammers, dollies, body file, body spoons, slappers, levers.
Purpose and operation of metal finishing are identified.
Range
repair, new panel, welds.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
16100 version 4
Page 2 of 3
Outcome 2
Prepare to repair minor panel damage in the motor body industry.
Evidence requirements
2.1
Damage is assessed to enable it to be repaired to the original shape of the
panel and according to company policy.
Range
2.2
Tools suitable for repairing damage are selected to enable the damage to be
repaired to its original shape.
Range
2.3
sight, feel, filing.
hammers, dollies, body file, spoons, slappers, disk sander, DA or
orbital sander.
Parts and fittings are removed to gain access to damage without damage to the
removed parts.
Outcome 3
Repair minor panel damage in the motor body industry.
Evidence requirements
3.1
Damage is repaired without stretching, and the panel is returned to its original
shape with no irregularities.
3.2
Panel is metal finished according to company policy and there are no
irregularities on the surface that may impair painting.
Range
file marks, deep sanding marks, dents, sharp edges.
3.3
No damage is caused to adjacent panels or fittings.
3.4
Safe working practices are carried out throughout the task.
Range
3.5
personal safety, safety to other people, vehicle safety, tool,
equipment and machine safety.
Tools and equipment are returned to their places, and the work area is clean.
Replacement information
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
This unit standard and unit standard 3875 have been
replaced by unit standard 21697 and unit standard
21695.
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
16100 version 4
Page 3 of 3
This unit standard is expiring. Assessment against the standard must take place by
the last date for assessment set out below.
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
10 February 1999
31 December 2016
Revision
2
13 March 2001
31 December 2016
Rollover
3
25 July 2006
31 December 2016
Rollover
4
19 November 2010
31 December 2016
Accreditation and Moderation Action Plan (AMAP) reference
0014
This AMAP can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA, or
an inter-institutional body with delegated authority for quality assurance, before they can
report credits from assessment against unit standards or deliver courses of study leading
to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Consent requirements and an outline of the moderation system that applies to this
standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The
AMAP also includes useful information about special requirements for organisations
wishing to develop education and training programmes, such as minimum qualifications for
tutors and assessors, and special resource requirements.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016