M-Weld Gravel Guard MB Fascia

advertisement
M-Weld Gravel Guard MB Fascia
ORDER / SPECIFICATION FORM
(For Built-Up and Modified Roofing)
FASCIA FORMED
IN 10'-0" LENGTHS
CONCEALED JOINT
SPLICE, 4" WIDE
1" 3
20GA GALV RETAINER
FORMED IN 10'-0" LENGTHS
24GA GALV WATER-DAM
FORMED IN 10'-0" LENGTHS
2 3/8"
CANT
MEMBRANE 2
BY OTHERS
FACE
MIN=5 1/2"
MAX=12 1/4"
BLOCKING
BY OTHERS
90°
COVERAGE
1
1-1/2" SS RING SHANK
NAIL, PROVIDED
1-1/2" SS RING SHANK NAIL,
PROVIDED FOR FACES
GREATER THAN 8" (CONTACT
MANUFACTURER IF FASTENER
WILL FALL ON BRICK/MASONRY)
5/8"
1 Face = Coverage (should extend a min. of 1" below water resistant wall surface)+ 4".
2 Coordinate installation with membrane manufacturer.
3 The dimension shown will vary depending upon the number of roofing plys used.
QUANTITY
Total LF (10'-0" pcs)
Miters (___ Outside, ___ Inside)
MATERIAL
THICKNESS
End Caps (___ Left, ___ Right)
0.050
Aluminum
End Terms (___ Left, ___ Right)
0.063
Galvanized
Radius LF (10'-0" pcs)
Stainless Steel
24GA
Ridge/Valley Miters
22GA
(Attach
Compound Miters
Sketches)
Special Corners
Sumps
Spill Outs
ACCESSORY TYPE
Welded
Folded
FINISH
Mill Finish
Prefinished Kynar
Post Finished Kynar
Prefinished Anodize
Post Finished Anodize
COLOR
0.063 prefinished Kynar is only available in Statuary Bronze, Medium Bronze, Sandstone, Dove Gray, Ascot White, Forest Green & Bone White
®
LA
SSI F I E
UL
D
ANSI/SPRI
ES-1 TESTED
(Contact manufacturer for verification of test
report data on your project)
C
APPROVALS
®
CUSTOMER APPROVAL
Approved for Fabrication
Approved with Changes Authorized Customer Signature
Disapproved, Resubmit
Title
R27207
Date
Job Name:
Customer:
By:
Job #:
Representative:
Date:
Architect:
Sheet
Location:
Rev. 12/15
1 Campus Drive - Parsippany, NJ 07054 - Phone: (877) GAF-ROOF / (877) 423-7663
www.gaf.com
of
M-Weld Gravel Guard MB Fascia
Face Minimum Maximum Water
Nailer
Dam
Height Fascia
Gauge Coverage Gauge
Fascia
Model
NPF-625
6 1/4"
0.050
2 1/4"
24GA
NPF-775
7 3/4"
0.050
3 3/4"
22GA
NPF-925
9 1/4"
0.050
5 1/4"
20GA
NPF-1075
10 3/4"
0.050
6 3/4"
20GA
1/4"
GAP
Intermediate formed fascia sizes may be specified within the
allowable range of 5-1/2" to 12-1/4".
FASCIA
CONCEALED
JOINT SPLICE
RETAINER
WATER-DAM
MEMBRANE
BY OTHERS
SEE NOTE
BELOW
SEE NOTE
BELOW
OUTSIDE MITER
24"
END CAP
30"
11"
7"
LEFT HAND SHOWN
SUMP
2 PIECE ASSEMBLY
SEE NOTE
BELOW
SEE NOTE
BELOW
24"
29"
INSIDE MITER
END TERM
RIGHT HAND SHOWN
Standard fascia miter leg lengths: 24" nominal
Standard fascia miter angle is 90°
For special miter requirements, attach sketches or consult manufacturer for assistance.
Rev. 12/15
6"
5"
SPILLOUT
3 PIECE ASSEMBLY
Download