M-Weld Gravel Stop MB Fascia B

advertisement
M-Weld Gravel Stop MB Fascia B
ORDER / SPECIFICATION FORM
(For Built Up or Modified Roofs)
1/2"
(min)
4 3/16" (min)
1/4"
(min)
FASCIA FORMED
IN 10'-0" LENGTHS
CONCEALED JOINT
SPLICE, 4" WIDE
MEMBRANE 2
BY OTHERS
5/16"
BLOCKING
BY OTHERS
FACE
MIN=2 5/8"
MAX=13"
COVERAGE
1
1-1/2" SS RING SHANK
NAIL, PROVIDED
CLEAT FORMED
IN 10'-0" LENGTHS
1-1/2" SS RING SHANK NAIL,
PROVIDED FOR FACES 4 7/8"
OR GREATER (CONTACT
MANUFACTURER IF FASTENER
WILL FALL ON BRICK/MASONRY)
5/8"
1 Face = Coverage (should extend a min. of 1" below water resistant wall surface)+15/16".
2 Coordinate installation with membrane manufacturer.
QUANTITY
Total LF (10'-0" pcs)
Miters (___ Outside, ___ Inside)
End Caps (___ Left, ___ Right)
End Terms (___ Left, ___ Right)
Sumps
Spill Outs
MATERIAL
THICKNESS
0.040
Aluminum
0.050
Galvanized
0.063
Stainless Steel
24GA
22GA
ACCESSORY TYPE
Welded
Folded
MODEL
MBED-B350
MBED-B500
MBED-B650
MBED-B800
FINISH
Mill Finish
Prefinished Kynar
Post Finished Kynar
Prefinished Anodize
Post Finished Anodize
COLOR
0.063 prefinished Kynar is only available in Statuary Bronze, Medium Bronze, Sandstone, Dove Gray, Ascot White, Forest Green & Bone White
®
LA
SSI F I E
UL
D
ANSI/SPRI
ES-1 TESTED
(Contact manufacturer for verification of test
report data on your project)
C
APPROVALS
®
CUSTOMER APPROVAL
Approved for Fabrication
Approved with Changes Authorized Customer Signature
Disapproved, Resubmit
Title
R27207
Date
Job Name:
Customer:
By:
Job #:
Representative:
Date:
Architect:
Sheet
Location:
Rev. 12/15
1 Campus Drive - Parsippany, NJ 07054 - Phone: (877) GAF-ROOF / (877) 423-7663
www.gaf.com
of
M-Weld Gravel Stop MB Fascia B
Face Minimum Maximum Cleat
Nailer
Gauge
Height Fascia
Gauge Coverage
Fascia
Model
MBED-B350
3 1/2"
0.040
2 9/16"
24GA
MBED-B500
5"
0.040
4 1/16"
24GA
MBED-B650
6 1/2"
0.040
5 9/16"
24GA
MBED-B800
8"
0.050
7 1/16"
22GA
1/4"
GAP
Intermediate formed fascia sizes may be specified within the
allowable range of 2-5/8" to 13".
FASCIA
CONCEALED
JOINT SPLICE
CLEAT
MEMBRANE
BY OTHERS
SEE NOTE
BELOW
OUTSIDE MITER
12"
30"
END CAP
LEFT HAND SHOWN
11"
7"
SUMP
SEE NOTE
BELOW
SEE NOTE
BELOW
2 PIECE ASSEMBLY
12"
29"
5"
INSIDE MITER
END TERM
RIGHT HAND SHOWN
SPILLOUT
2 PIECE ASSEMBLY
Standard fascia miter leg lengths: 12 1/2" nominal
Standard fascia miter angle is 90°
For special miter requirements, attach sketches or consult manufacturer for assistance.
Rev. 12/15
Download