EverGuard Snap-On Fascia
ORDER / SPECIFICATION FORM
(For EPDM or Similar Flexible Membrane Only)
FASCIA FORMED
IN 10'-0" LENGTHS
CONCEALED JOINT
SPLICE, 4" WIDE
2 1/2"
CANT
3
MEMBRANE
BY OTHERS
2
BLOCKING
BY OTHERS
90°
#9 x 1-1/2" SS SCREW w/
WASHER, PROVIDED FOR
FACES 10" OR GREATER
FACE
MIN=4 3/4"
MAX=12"
1-1/2" SS RING SHANK
NAIL, PROVIDED
COVERAGE
GALV SPRING CLEAT
FORMED IN 10'-0" LENGTHS
1
1-1/2" SS RING SHANK NAIL,
PROVIDED FOR FACES 8" OR
GREATER (CONTACT
MANUFACTURER IF FASTENER
WILL FALL ON BRICK/MASONRY)
5/8"
1 Face = Coverage (should extend a min. of 1" below water resistant wall surface)+3 1/8".
2 Coordinate installation with membrane manufacturer.
3 Standard fascia will NOT function with TPO membranes thicker than 0.060, contact
manufacturer when TPO exceeds 0.060.
QUANTITY
Total LF (10'-0" pcs)
Miters (___ Outside, ___ Inside)
Zee Miters
MATERIAL
THICKNESS
ACCESSORY TYPE
FINISH
End Caps (___ Left, ___ Right)
Welded
Mill Finish
0.050
Aluminum
End Terms (___ Left, ___ Right)
Folded
0.063
Prefinished Kynar
Galvanized
Radius LF (10'-0" pcs)
0.080
Post Finished Kynar
Stainless Steel
MEMBRANE
Ridge/Valley Miters
Prefinished Anodize
24GA
EPDM
(____mil)
(Attach
Post Finished Anodize
Compound Miters
22GA
TPO
(____mil)
Sketches)
Special Corners
PVC (____mil)
Sumps
COLOR
Spill Outs
®
0.063 prefinished Kynar is only available in Statuary Bronze, Medium Bronze, Sandstone, Dove Gray, Ascot White, Forest Green & Bone White
LA
SSI F I E
UL
D
ANSI/SPRI
ES-1 TESTED
(Contact manufacturer for verification of test
report data on your project)
C
APPROVALS
®
FM
Approved
CUSTOMER APPROVAL
Approved for Fabrication
Approved with Changes Authorized Customer Signature
Disapproved, Resubmit
Title
R27207
Date
Job Name:
Customer:
By:
Job #:
Representative:
Date:
Architect:
Sheet
Location:
Rev. 12/15
1 Campus Drive - Parsippany, NJ 07054 - Phone: (877) GAF-ROOF / (877) 423-7663
www.gaf.com
of
EverGuard Snap-On Fascia
Face Minimum Maximum Spring
Nailer
Cleat
Height Fascia
Gauge Coverage Gauge
Fascia
Model
EC1-550
5 1/2"
0.050
2 1/4"
24GA
EC1-700
7"
0.050
3 3/4"
24GA
EC1-850
8 1/2"
0.050
5 1/4"
24GA
EC1-1000
10"
0.063
6 3/4"
22GA
1/4"
GAP
Intermediate formed fascia sizes may be specified within the
allowable range of 4 3/4" to 12".
FASCIA
CONCEALED
JOINT SPLICE
MEMBRANE
BY OTHERS
SPRING CLEAT
SEE NOTE
BELOW
SEE NOTE
BELOW
OUTSIDE MITER
24"
END CAP
30"
11"
7"
LEFT HAND SHOWN
SUMP
2 PIECE ASSEMBLY
SEE NOTE
BELOW
SEE NOTE
BELOW
24"
29"
INSIDE MITER
END TERM
RIGHT HAND SHOWN
Standard fascia miter leg lengths: 24" nominal
Standard fascia miter angle is 90°
For special miter requirements, attach sketches or consult manufacturer for assistance.
Rev. 12/15
6"
5"
SPILLOUT
3 PIECE ASSEMBLY