EverGuard EZ Fascia EX

advertisement
EverGuard EZ Fascia EX
ORDER / SPECIFICATION FORM
(For Single-Ply Membrane)
FASCIA FORMED
IN 10'-0" LENGTHS
2 1/4"
RETAINER SPLICE
w/ GASKET, 6" WIDE
MEMBRANE 2
BY OTHERS
3/4"
90°
FACE/
MODEL COVERAGE
3
1
BLOCKING
BY OTHERS
SEALANT BY
INSTALLER
#9 x 1-1/2" SS SCREW w/
WASHER, PROVIDED
CONCEALED JOINT
SPLICE, 4" WIDE
EXTRUDED RETAINER,
10'-0" LENGTHS
1/2"
1/2"
1 Face = Coverage (should extend a min. of 1" below water resistant wall surface)+1 1/4".
2 Coordinate installation with membrane manufacturer.
3 Only standard model face sizes are available with a 1-piece retainer. For other sizes use
separate Order / Spec form for custom sizes, which has a 2-piece retainer.
QUANTITY
Total LF (10'-0" pcs)
Miters (___ Outside, ___ Inside)
MATERIAL
THICKNESS
End Caps (___ Left, ___ Right)
0.040
Aluminum
End Terms (___ Left, ___ Right)
0.050
Galvanized
Radius LF (Notched - 10'-0" pcs)
0.063
Stainless Steel
Vaulted LF (Welded - 5'-0" pcs)
24GA
Sumps
22GA
Spill Outs
Special Corners
(Attach Sketches)
ACCESSORY TYPE
Folded
FINISH
Mill Finish
Prefinished Kynar
Post Finished Kynar
Prefinished Anodize
Post Finished Anodize
MODEL
375
525
675
825
1125
COLOR
®
0.063 prefinished Kynar is only available in Statuary Bronze, Medium Bronze, Sandstone, Dove Gray, Ascot White, Forest Green & Bone White
LA
SSI F I E
UL
D
ANSI/SPRI
ES-1 TESTED
(Contact manufacturer for verification of test
report data on your project)
C
APPROVALS
®
CUSTOMER APPROVAL
Approved for Fabrication
Approved with Changes Authorized Customer Signature
Disapproved, Resubmit
Title
R27207
Date
Job Name:
Customer:
By:
Job #:
Representative:
Date:
Architect:
Sheet
Location:
Rev. 12/15
1 Campus Drive - Parsippany, NJ 07054 - Phone: (877) GAF-ROOF / (877) 423-7663
www.gaf.com
of
EverGuard EZ Fascia EX
Fascia
Model
Nailer
Nailers
Face
Height Coverage Covered
375
3 3/4"
2 1/2"
1
525
5 1/4"
4"
2
675
6 3/4"
5 1/2"
3
825
8 1/4"
7"
4
1125
11 1/4"
10"
6
1/4"
GAP
FASCIA
CONCEALED
JOINT SPLICE
EXTRUDED
RETAINER
RETAINER SPLICE
w/ GASKET
MEMBRANE
BY OTHERS
SEE NOTE
BELOW
24"
OUTSIDE MITER
END CAP
30"
11"
7"
LEFT HAND SHOWN
SUMP
2 PIECE ASSEMBLY
SEE NOTE
BELOW
SEE NOTE
BELOW
24"
29"
INSIDE MITER
END TERM
2 PIECE ASSEMBLY
RIGHT HAND SHOWN
5"
SPILLOUT
Standard fascia miter leg lengths: 12" nominal
Standard fascia miter angle is 90°
For special miter requirements, attach sketches or consult manufacturer for assistance.
Rev. 12/15
3 PIECE ASSEMBLY
Download