1 - State Bank of Hyderabad

advertisement
INTERIOR FURNISHING WORKS OF STAFF TRAINING CENTER
AT WEST MAREDPALLY, SECUNDERABAD
STATE BANK OF HYDERABAD
PREMISES DEPT, 2ND FLOOR,
METHODIST COMPLEX, ABIDS
HYDERABAD-500001
TENDER SCHEDULE.
Part II - PRICE BID
The Assistant General Manager, Premises and Estates Department,
STATE BANK OF HYDERABAD,
2nd Floor, Methodist Complex,
ABIDS,
HYDERABAD 500001
Schedule of quantities for Interior Furnishing Works at Staff Training Center, West Maredpally,
Secunderabad
S.No
1
2
Description of Items
Tables For Computers Channels: Counter
shall be made up of 19mm BWR ply wood
with 1.00mm thick laminate of approved
shade. The table shall have 1 1/2"x1" beach
wood edge beading with melamine polish.
Running counter shall have a Keyboard, all
hardware complete. The table to have a
drawer unit below the table top on telescopic
channels. Inner surface of the drawer unit and
counter shall be finished with 0.7mm thick
laminate. The table should have keyboard
tray, drawer unit vertical partition below table
at every 4'-0" length. A continuous slit of size
9” width and 5” depth is to be made on table
top as shown in drawing. Provision shall be
made for CPU trolley and footrest. Complete
as per Bank / Architect direction. (Drg:
SBH/STC/DET01)
Providing & erecting in position stage (raised
platform) in M.S Box Sections framework at
every 2-6" centers grid with MS box channel
verticals at every 2'-6" centers to be finished
with approved epoxy paint including primer
including providing & fixing 19mm thk Pine
based Block board on top of the frame work
including creating steps in M.S Box Sections.
. (Drg: SBH/STC/DET02)
Oty
Unit
300
Rft
1400
sft
Rate
Amount
3
4
FULL HEIGHT PARTLY GLAZED
PARTITIONS:
Providing, fabricating and fixing metal stud
partitions with the following specifications in
approved design/drawing. 1).The supporting
system comprising of gypsteel/Boral make
51mmx35mmx0.55mm metal studs at 600mm
c/c and 51mmx32mmx0.55mm metal tracks at
floor, middle, door and ceiling level with joints
staggered to avoid through joints. The vertical
member should touch with horizontal
ceiling/channel at slab/beam bottom. The rate
should also include necessary strengthening
with studs/tracks or channels at doors and
other openings. 2).frame work has to be
raised up to the concrete ceiling/beam as
support.
3).Fixing 9mm ply with 25mm dry wall screws
by using jointing compound and fiber glass
mesh tape for the entire height of the partition
and 1mm laminate on both sides of frame up
to 900mm and above 2100mm level to top
level with grooves in laminates as directed at
site.
4).8mm thick clear float glass with
etching(Etching cost considered @ ` 40/sft) as
directed with necessary 12mm tk. steam
beach wood beading with melamine polish
for heights between 900mm and 2100mm. .
(Drg: SBH/STC/DET03)
FULL
HEIGHT
SOLID
PARTITIONS:
Providing, fabrication and fixing metal stud
partitions with the specifications as mentioned
in Item No:3 above except that no glass is to
be provided. Total partition is to made solid on
both sides with ply wood and laminate with
above
mentioned
specifications.
(Drg:
SBH/STC/DET05)
5
LOW HT. PARTITION.
Providing & fixing metal stud low height
partitions with the following specifications:
(a) Supporting system comprising of
Gypsteel / Boral make 51mm x 35mm metal
studs of 0.55mm at 600mm c/c and 51mm x
32mm metal tracks at floor, middle and top of
the partition with joints staggered to avoid
through joints. The rate should also include
necessary strengthening with studs / tracks
or channels at doors and other openings.
(b) 8mm ply with 1mm laminate to be pasted
on both sides upto the desired height with
grooves in laminate as directed at site.
(c) 8 mm thick clear float glass with etching
(cost of etching @ Rs.50/- per Sft) with
necessary teak wood beadings finished with
melamine spray polish.
80
Sft
300
Sft
150
Sft
6
7
OFFICER WORK STATION:
Providing, fabricating and fixing Clerical work
station consists of Table (5’.0”x2’3”x2’6”)
made with 19mm Plywood (of approved make)
as detailed below.
1).Table should have one side 18" wide and 2’
deep storage unit consisting of one sliding
drawer at top and bottom with openable
shutter, arrangement for CPU stand, One
Moulded Key Board Tray with channels, cable
manager and foot rest of 4"x1.5" Saal wood
section shall be provided and the three edges
of front fascia shall be 1.5" thick with
additional ply and leaped with necessary
steam beach wood beading dully melamine
spray polished. All drawers shall be fitted with
telescopic channels and automatic push type
locking arrangement
All exposed edges of plywood shall be fitted
with steam beach wood beading duly
melamine spray polished. All visible surfaces
such as front, sides, top, back, drawer outside
etc.shall be laminated with 1 mm thick of
approved shade and make. All invisible
surfaces such as drawer inside, drawer
supporting cabinet, inside cupboard etc. shall
be laminated with 0.7mm thick laminate. The
rates should include locking arrangement (to
be operated by single key) for all drawers and
cupboard along with best quality 4” brush steel
handles,
sliding
telescopic
channel,
arrangements etc. complete. Cost should also
inclusive of paneling, lapping of edges with
plywood to achieve thickness as per Engineerin-charges design. . (Drg: SBH/STC/DET05)
SYSTEM ROOM WORK STATION:
Providing, fabricating and fixing of Computer
desks of 2.5’ H x 2.0' D size in the given
length and made with 19mm Plywood (of
approved make) frame work having one 16"
wide and 2’ deep storage unit at every 4.0’
length. Arrangement of Moulded Key Board
Tray with channels, cable manager and foot
rest of 4" x 1.5" Saal wood section shall be
provided at every 4’ length. Each storage unit
shall consist of four sliding drawers of 5"
height & the drawers shall be fitted with
telescopic channels and automatic push type
locking arrangement, brush steel finished
handle and all exposed edges of plywood
shall be fixed with steam beach wood beading
finished with melamine polish. All visible
surfaces such as front, sides, top, back,
drawer outside etc.shall be laminated with 1
mm thick of approved shade and make. All
invisible surfaces such as drawer inside,
drawer supporting cabinet etc. shall be
painted with two coats of enamel paint with a
coat of primer and putty. The rates should
include locking arrangement for all drawers
alongwith best quality 4” brush steel handles,
etc. complete. Cost should also inclusive of
paneling, lapping of edges with plywood to
achieve thickness as per design and approval
10
Nos
10
Rft
of Engineer-in-charges.
8
9
10
11
Providing and fixing water proof solid core
FLUSH DOORS shutters 35mm thk (TW wood
beading of 0.5" x 1.25" to be provided all
around) of approved make as per ISI
specifications and 1mm thk shell finish
laminate on both sides with vision hole cutting
with 6mm thk plain glass as indicated. The
shutter shall be fixed to existing partition frame
work, necessary hardware fittings like brass
butt hinges, door closers, locks, tower bolts,
handles etc.of approved make, including all
incidental and operational charges etc.,
complete
Sliding Folding Partition System For
Conference: Providing and fixing. Panel
construction with Aluminium frame, Panel
width 900mm ,and Panel thickness 80mm,
Suspension method Floor supported with top
guide track or top hung no floor track.
Individual panel Hinged and Seal type Fixed
top and bottom sweep strips, and Manual
Operation mode. Centre folding - single unit or
bi-parting to both sides Enfolding - single unit
or bi-parting to both side. The paneling must
be acoustically insulated with suitable sound
absorbing material in the partition. Both sides
of frame work is to be fixed with 19mm thick
BWR grade plywood and laminated with
1.00mm thick laminate of approved shade.
White Board With Glass Shelf for class room:
Providing and fixing non-reflective, anti glare
toughened glass writing board of 12mm thick
with back opaque white film. The board should
be firmly fixed to the frame work with heavy
duty studs. The frame work is to be made with
2” x 2” teak wood sections at 2’-0” c/c
FALSE CEILING(GYPSUM BOARD)
Providing and fixing of false ceiling made of
12mm thick gypsum board (flat type) with
necessary opening for light fittings. False
ceiling shall be fitted to GI frame as detailed
below.
Ceiling channel (MF5) of size 80mm x 26mm x
0.5mm at every 457mm c/c.
Intermediate channel (MF7) 15mm x 45mm x
0.9mm at every 1220mm c/c.
Perimeter channel (MF6A) 20mm x 26mm all
along wall.
Strap hanger (MF8) on suspending the frame
work 25mm x 0.5mm with nuts and
bolts(PS26) 6.4mmx12.7mm.
Connecting clip (MF9) of 2.64mm thick.
Dry walls screw of 25mm long
Dash fastener12.5mm diax35mm long with
6mm dia bolt. The gypsum boards are to be
jointed and finished so as to have a flush look
which includes finishing the edges of the
board with jointing compound, paper tape etc.
The rate should include painting one coat of
primer and putty and two coats of Asian
Interior
Plastic
Emulsion
of
white
35
sft
400
Sft
200
Sft
15000
Sft
shade.(measurement will be on area only for
all types of width)
12
13
14
GRID
TYPE
FALSE
CEILING:
Providing & Fixing of Armstrong Mineral Fibre
Acoustical Suspended Ceiling System as per
the design including all necessary fixtures,
fasteners, additional stiffening members for
the light fixtures panel, all complete with
MINATUFF
TEGULAR
TILES
WITH
ARMSTRONG
SILHOUETTE
SUS.
EXPOSED GRID as per manufacturer’s
specification. The tiles should be white Colour
and in the size of 600 X 600 X 16 mm with Bio
Block coating on the face of the tile. The tile
shall be laid on Armstrong Silhouette profile
grid system with 15mm white flanges
incorporating a 6mm central reveal in white
colour and with a web height of 45mm and a
load carrying capacity of minimum 15.68
Kgs/M2. Silhouette, Main Runners & Cross
Tees to have mitred ends & “birdsmouth”
notches to provide mitred cruciform junctions.
Installation: To comprise main runner spaced
at 1200mm centers securely fixed to the
structural soffit using Armstrong suspension
system (specifications below) at 1200mm
maximum centre & not more than 150mm
from spliced joints. The First/Last Armstrong
suspension system at the end of each main
runner should not be greater than 600mm
from the adjacent wall.
1200mm long
cross tees to be interlocked between main
runners at 600mm centre to form 1200 x 600
mm module. Cut cross tees longer than
600mm require independent support. 600 x
600mm modules to be formed by fitting
600mm long cross tees centrally between the
1200 mm cross tees. The 1200mm cross tees
to have central “birds mouth” notches to
facilitate fitting of 600mm cross tees.
Perimeter trim to be Armstrong shadow wall
molding
(dimensions:
19x7x7x14mm),
secured to walls at 450 mm maximum centers.
Providing and erecting in position Plaster of
Paris Cornices 3" x 3" in size to the false
ceiling. Including filling the gaps with POP &
painting the same with Acryllic Emulsion paint
of approved colour and texture as per
instruction of Architect.
Providing and supplying study table of size 4'0" x 2'-0" to be made out of 19mm thk.
Commercial Plywood top and the sides
including 4" high drawer for the entire length of
the table. All the external surfaces finished
with 1.5mm thk approved laminate. 1" x 1"
t.w.beading shall be fixed on table top edges.
All the necessary brass fittings such as
hinges, ball catches, wire manager, locks etc.
complete as per instructions. complete as per
drawing & instructions of the Engineer in
charge.
3990
Sft
6000
Rft
120
Nos
15
16
17
18
19
20
21
22
22a)
23
VERTICAL BLINDS: Providing and fixing
100mm wide vertical blinds of Vista/Mac make
of approved range with louver made of
polyester base fabric and providing with
guardian tilter wand cord accessories like
head channel, end control unit, tilt rod, tilter
chain, carrier, space, bottom mechanism,
cord, cord weight, installation, etc; of approved
color and texture. complete as per Bank /
Architect direction.(Make : Vista/ Mak)
Supplying and fabricating head rest of size 8'0" x 2'-0" length made with 12mm BWR ply
wood and 4" thick foam. Foam is to be coverd
with a fabric of approved shade. T he basic
rate of fabric is to Rs350.00 per Mt. Boards
are to be fixed to wall
with necessary
hardware.
Removing & Re-fixing of old cupboards:
The cup boards are to be removed and refixed in position. Rate quoted should include
necessary materials. Internal exposed ply
surfaces to be painted with two coats of
synthetic enamel paint.
Removing FULL HEIGHT PARTITION with
double skin, for class room and computer
room.
Removing Existing Grid FALSE CEILING in
Class r00ms
Lamination of Doors: Providing and fixing
6mm plywood to existing door and laminating
exposed surface with 1mm thick laminate of
approved make and shade on both sides of
door. The Doors are to be re-fixed with
necessary hardware like Brass Hinges, Brass
Tower bolts. Etc. Rate quoted should include
for both faces of door. Only door
measurement will be taken
Providing and fixing with necessary hardware
Door locking system with brass body coated
with SS finish latch of 300mm long.
Providing and fixing Automatic Door closures
of approved makes to existing Doors
WALL/ COLUMN PANELLING:
Providing, and fixing of wall/column paneling
made with 9mm plywood glued with 1mm thick
lamination over Gypsteel / Boral makes 51mm
x 35mm metal studs as detailed in (Full height
partition) above. The rate should be inclusive
of providing texture painting in between and
providing steam beach cornice between
paneling and texture paint. The necessary
provision in framework for running of Electrical
conduit has to be made.(contractor should
ensure that pipes are laid before proceeding)
Providing and laying Wooden flooring of
approved make on floor in a design
combination of two different colours as per
instructions on leveled floor including
insulating the areas, surface preparation,
bedding, finishing, polishing, cleaning etc
4000
Sft
60
Nos
347
Sft
432
Sft
4000
Sft
3360
Sft
120
Nos
120
Nos
2000
Sft
2000
Sft
complete as per the directions and instructions
of the Engineer-in-charge. The rate shall be
inclusive of edge moulding & end strips at the
junction between the floor and the vertical
surfaces and mouldings, T grooves etc
complete. As per the directions / to the
satisfaction of the Architect. (Basic rate of
tiles = Rs. 180 / Sq Fts.)
TOTAL
Discount if any (Express in terms of
percentage)
NET TOTAL
Signature of agency with Seal
Download