BILL OF QUANTITIES FOR THE PROPOSED INTERIOR WORK AT
CANARA BANK – DHARAPURAM BRANCH.
S.No
DESCRIPTION
QTY
RATE
UNIT
INTERIOR WORKS
01.
Supplying and fixing of Gypsum board 1400 Sft
panel false ceiling using galvanized
sections for hanging and holding the
gypsum board panels of 12mmtk with
approved design 5”ht cornice works
alround duly painted with three coats
of plastic emulsion paint after
necessary Pattiworks. Provisions are to
be made for fixing of A.C.Grills, light
fittings as per consultants instructions
including making holes and to assist in
fixing the same etc.,
Sft
AMOUNT
02.
Dismantling the Existing partition and
providing full height partitions of
height 10’0” made of 3’x2” salwood
frame work finished with 2 coats of
termite resistant coating (to be
approved by architect) with vertical
member at 10’6”, level 8’0” level 4’0”
level & floor level. The frame work to
be cladded on both sides with 9mm
thick marine plywood and finished
with 1 mm thick decorative laminate.
Front portion with 5mm tk glass 2’0”
Ht. The partition to be provided with
TW skirting of size 3” x ¾” on both
sides and finished to desired wood
effect by application of melamine
polish after initial surface preparation.
with all fixing arrangements, locks
and hardwares etc complete.
(Appraiser)
170 Sft
Sft
03.
Dismantling the existing partition and
Supplying and fixing of side partition
for Audit/Inspection room & Power
Room using aluminimum anodized
section frame work with top, middle
and bottom portion with marine
plywood particle board (9mm tk) and
finished with 1mm tk. Decorative
laminate, with all fixing
arrangements, EPDM rubber gaskets
locks and hardwares etc complete.
160 Sft
Sft
04.
Low Height Storage
Low height storage made out of 19mm
marine plywood particle board for top,
bottom.sides, shutter and shelves with
top finished with 1mm tk. laminate
40 Sft
Sft
sheet, inner surface to be with 2 coats
of enamel paint.
Size 5’3’’x1’3’’x 2’9”(Officer
Cabin/Inspector cabin)
05.
Officer Table
Providing table for Officer of size 5'0"
x 2 '6" and height of 2’6” made of
18mm thick marine plywood for table
top. Vertical sides and modesty panel.
The surfaces of marine Plywood
finished with approved colour of 1mm
thick decorative laminate and all inside
surfaces finished with 2 coats of
approved colour of synthetic enamel
paint over a primer coat. The table
also composed of a drawer of depth
0’4” made of 18mm thick marine
Plywood. The compartment to also
have shutter made of 18mm thick
marine Plywood finished with
approved colour of 1mm thick
decorative laminate & inside surfaces
finished with 2 coats of approved
colour of synthetic enamel paint over a
primer coat. All exposed edges lipped
with TW beading of size 1” x ¾” &
polished to desired wood effect after
initial surface preparation. The drawer
to have a set of sliding wheels of
approved quality for easy operation.
The entire unit to be complete with all
accessories such as knobs handles lock
and key arrangements of approved
quality. The table to have a TW foot
rest of size 3” x 1½” finished suitably.
1 No
No
06.
Removing the ex. Laminations for all
the existing tables and the surface of
the Plywood finished with approved
colour of 1mm thick decorative
laminate & inside surfaces finished
with 2 coats of approved colour of
synthetic enamel paint over a primer
coat.
07.
Miscellaneous Items
Pin up Board
a)
Supplying and fixing of pinup Board of
size 3’0” x 3’0” made of 8mm plywood
frame filled with soft board covered
with fur. The colour of the fur is to be
selected by the Architect. The outer
teak wood frame of the pinup board to
be finished with melamine of approved
colour.
b)
WRITING LEDGE & BROCHURE
HOLDER:
Fabricating and fixing of writing ledge
and brochures holder size 6’0”x1’0”
made of 12mm glass supported with
18mm marine plywood stand finished
with duco automotive paint so as to
match the colour of the interiors.
Glass edge beveled to half round shape
suitably supported on plywood as per
design. The work has to be completed
as per architects direction.
600 Sft
Sft
1 No
No
1 No
No
08
a)
PAINTING WORKS:
Painting with internal walls putty finish
with two coats of primer and two coats
of glacier white (Code-40028) colour
emulsion paint of Nerolac all caps
emulsion (or) equivalent in all height of
walls including scaffolding, cleaning
and supply of all materials complete.
The work has to be completed as per
architect direction. This includes
removing of existing distemper by
scraping and scrubbing(For Banking
Hall)
1600 Sft
Sft
b)
Painting with internal walls with two
coats of primer and two coats of Oil
bound Distemper of Asian paint in all
height of walls including scaffolding,
cleaning and supply of all materials
complete. The work has to be
completed as per architect direction.
This includes removing of existing
distemper by scraping and
scrubbing(For Other Places)
2200 Sft
Sft
c)
Painting the joineries with 3 coats of
enamel paint over the priming coat of
approved colour
1000 Sft
Sft
TOTAL
CLAUSE:
Providing temporary arrangements for functioning of branch, throughout the
course of completion of work. Dismantling the existing counter table etc., and
reassembling them in a preferred location as instructed by Bank/Consultant to
facilitate the commencement of works without affecting the daily operation of
the bank.
NOTE:
The contractor shall not be paid anything extra subsequently and the rates
shall suffice for all temporary arrangements sought by the bank till the
completion of the works including all cleaning works and which shall result
during the progress of the work.
SPECIFICATION OF MATERIALS
INTERIOR FURNISHING & CIVIL WORKS
01.
Aluminium
:
Indal/Zindal
02.
Wood
:
Teak Wood(chemically treated)
03.
Plywood
:
Green ply, Marine ply, Uniply,
Anchor, ISI approved
04.
Laminate Sheet
:
Green Lam/Merino
05.
Locks
:
Laxmi/Godrej
06.
Door Closer
:
Everite/Doorman
07.
Hardwares
:
EL Co.or equivalent
08.
Putty/Paint
:
Asian/ICI/Berger
09.
Glass
:
Modi, Sant Gobain
10.
Furniture
:
Godrej