Part 2. PRICE BID - State Bank of Hyderabad

advertisement
ULWE- NAVI MUMBAI BRANCH
TENDER SCHEDULE.
Part 2. PRICE BID
INTERIOR FURNISHINGWORKS
CONSULTANTS
SATYAJIT RANE & ASSOCIATES
ARCHITECTS & DESIGNERS
1076/24, OLD CHATURSRINGI ROAD,
PUNE 411016
MOB: +91 98900-84268
EMAIL: satyajit.rane@gmail.com, satyarch@rediffmail.com
The Dy. General Manager, Premises and Estates Department,
STATE BANK OF HYDERABAD,
2nd Floor, Methodist Complex,
ABIDS,
HYDERABAD 500001
040-23387371/250/275
Name of the Contractor to whom issued: ______________________________
Address: _________________________________________________________
_________________________________________________________________
_________________________________________________________________
SPECIFICATIONS AND BOQ FOR THE PROPOSED INTERIOR WORK TO BE EXECUTED AT
STATE BANK OF HYDERABAD ULWE- NAVI MUMBAI BRANCH ,
GENERAL INSTRUCTION TO THE
CONTRACTOR
THE CONTRACTOR SHALL STRICTLY ADHERE TO THE FOLLOWING INSTRUCTIONS UNLESS
MENSIONED IN THE BOQ.
1
19mm Plywood to be used for all table tops, verticals,key board slider, draw sides. / 12mm for the
modesty panel , in case of curvatures 2 nos. 6mm Flexible plywood to be used.
2
All table tops with 1.5mm thick Laminate, All vertical and exposed outside and all internal visible surface
of the plywood, all inside the doors , shelves tops, all internal area of drawer should be covered with
1mm thick Laminate.
3
All the storage unite and flap doors should be fixed with Box hinges and Key board slider should slide on
Telescopic channels only.
4
The design patterns / drawing indicated in the tender are tentativeonly and The final patterns and shades
/ colors should be as per the instructions of the Architect / Bank authority.
5
All tables/ counters should be provided with CPU stand for keeping CPU below the counter .
6
Foot rest of 2"x3" teak wood should be provided for all the tables and counters with duly polished finish.
7
All the exposed edges of plywood / partitions / doors must be covered with 12mm thick and respective
thickness Steam beech wood rippers as per design and duly melamine polished.
8
Any discrepancy in the site conditions / measurements in the drawings shall be brought to the notice of
the Architects office.
9
For Round / Curve shaped counters / tables the measurement will be taken in the center of the top width
for billing purpose.
10
Cost of Taps / plumbing / drainage should be included with all the fitting given in the tender , No separate
claim will be allowed for this.
11
Contractor should work keeping running banks time in mind and bank authority decision will be final on
the timings.
12
As the Branch is in working form, the work to be done should be in phases and should cooperate other
agencies working.
13
Cable managers should be provided wherever
required by the bank.
14
Contractor Should not object for any deduction in the items of
said work.
APPROVED BRANDS / MAKES ( AND OR AS PER MENTIONED IN THE TECHINCAL BID )
The brands are to be used in the sequence mentioned.
A
PLYWOOD I.S 303 COMMERCAL GRADE :DURO PLY( PUMAPLY ), CENTURY,
GREENPLY,
B
LAMINATE : FORMICA , ROYAL TOUCH , , GREENLAM. MARINO::: NATURAL VENEER :
TRUWOOD, DURO, NATURAL, CENTURY.
C
MDF BOARD -EXTERIOR GRADE: GRADE-I , IS 12406 of 2003 : NUWUD , DURATUFF,
GREEN PANLEMAX EXTERIOR GRADE.
D
LOCKS : EBCO ,GODREJ, , DOOSET for Doors , Storages.
E
CHANELS : EBCO (Telescopic Chromium Plated), HETTICH.
F
MAIN DOOR / DOOR / STORAGE DOOR HANDLES: DORSET , KITCH, GODREJ
G
DOOR CLOSER/ FLOOR SPRING/ PATCH FITTINGS : DORMA, GODREJ.
H
GYPSUM BOARD: INDIA GYPSUM , BORAL PASTER BOARD.
I
24"X24" GRID CEILING BOARD: ARMSTRONG, DAIKEN, NITTIBO. RH 90 GRADE
SILLHOUTTE GRID.
J
GLASS : MODI FLOAT, SAINT GOBAIN.
K
VERTICAL BLINDS ( WITH SCOTCH GUARD ): VISTA ,MAC.
L
WALL PAINTS: ICI VELVET TOUCH , ASIAN ROYALE EMULSION.
M
TEXTURE ( Exteriors and Interiors ): SPECTRUM , WALL TEXTURES.
N
ROLLER TEXTURE: ICI DUET, BURGER PAINTS.
O
WOODEN FRAME/ BEADING: STEAM BEECH WOOD.
P
VITRIFIED TILES 24"X24": RAK CERAMICS, VARMORA, ASIAN.
Q
GROUTING/ADHESIVE FOR VETRIFIED TILES: LATICRATE, FOSROCK.
R
CERAMIC FLOOR / WALL TILES ; JOHNSON, KAJARIA, SOMANY.
S
TOILET FITTINGS: CERAWARE, HINDWARE, PARRY WARE.
T
TAP FITTINGS: ESS ESS , MARC, PARRY WARE.
U
FOAM : KING FOAM.
V
UPHOLSTRY: HARMONY
W
CHAIRS: GODREJ, GARNIER.
BILL OF QUANTITIES - INTERIOR WORKS IN SBH-ULWE BRANCH NAVI MUMBAI (NEW PREMISES)
area statement of premises
GROUND FLOOR
2098
SFT
A
INTERIOR WORKS
no item of work
1 COMPUTER CLERICAL COUNTER ( in curve profile)
unit
r.m
Manufacturing, supplying and fixing of computer counter made
to shape as per approved design / drawing / size (4.5 ft.
approx. W x 2.5 ft. H x 3.0 ft. D) and made with necessary
19mm Plywood (of approved make) frame work having one
side 16" wide storage unit consisting of 3 Nos. of sliding 5.0”
deep drawers with telescopic channels and automatic push type
locking arrangement.the bottom drawer shall have provision for
vertical file storage The top shall be in solid acrylic (measured
and paid for seprately, refer below). CPU stand, keyboard
drawer, foot rest and cable manager to be provided. All visible
surfaces shall be laminated with 1.0 mm thick laminate of
approved shade and make. All invisible surfaces of plywood
shall be french polish. All exposed edges of plywood shall be
fixed with agrowood beading finished with zinc oxide polish of
matching color and a footrest of 100mm x 35mm teak wood
section shall be provided with dully polished. The top will also
have12mm thk glass with edges rounded glass fitted on SS
studs, drawer locks (to be operated with single key) handles
and other necessary hardware’s should be included in rate
mentioned. Complete
2 COMPUTER CASH COUNTER
r.m
Providing and erecting computer cash counters as per
specification of above said computer clerical counter. In
addition, an in-built Service top of 15” wide will be provided in
the frame work at 1.5’ height from the table top shall be in
solid arcylic (measured and paid for seperately) Further, 12
mm thick. Float glass with specified cutout hole shall be
provided on service top till 7’ ht and fixed in 1.0’ high wooden
frame with beach wood beading of 1” x 0.5” size. There will 3
drawers, two of them will be cash drawers with partitiongrid
for keeping notes in 12 mm ply with lipping and french polish
finsih with All beading surfaces to have zinc oxide polish of
qty
6.7
1.5
3 12MM GLASS ON COUNTERS. ( front glass) in curve sq.m 6.5
profile.
Providing and fixing in position 12mm thick good quality glass
made to shape of curved or straight pattern and fixing with
best quality D type brackets to the low height partitions on
counters and cash counter. Cash counters will have this 12mm
glass above the level of 750mm ht of low height partitions.
Where beading is required, it should be rubberwood with
natural polish The glass should have etching / film pasting / 3m
film / one way vision film with write ups as suggested.
4 PARTITIONS
sq.m 90
rate (`)
amount(`)
Providing and fixing Full ht double skin Partitions / Full
height Partly Glazed & Partly solid partitions / Low
height solid & glazed Partitions (straight and curved in
plan) as per specification including skirting, complete as per
drawings and instructions. Complete in all respects. The rate
shall be inclusive of the necessary hardware, providing suitable
doors at all locations wherever required with SS approved
hardware such as hydarulic door closer (DORMA/SIO), handles,
mortise latches or tubular latches etc complete. Area of the
doors shall be treated as partition & measured along with
Main frame - G.I Frame work Boral make 51mmx35mm metal
studs at 600mmc/c and 51mmx32mm metal tracks at 2'0"c/c
with joints staggered to avoid through joints or equavalent
with extra frame below slab soffit for conduit to run above. All
verticals secured to slab ceiling.
Skin:- Both side with 6 mm thk ply screwed to frame work on
both sides with joints as shown or directed. The rate shall be
inclusive of Patta with grooves, borders, bottom, middle & top
as advised by bank. 2 nos of 6mm plywood shall be used for
curved portion to bend easily.
For Glazing Skin:- 12.0 mm thk. etched modi float glass
Straight / segmented glass with etching of approved design
and drawing fixed with 32x10mm thk.RUBBER WOOD.
moulding and 3'-0" high solid portion as shown in the drawing
or as directed by Architect. Curved glass should be provided to
match the decorum of the interiora as per the plan
indicated.with
as shown
all doors (solidbank
flushlogo
dooretching
type) with
matching laminate and SS
hard ware of handles, tubular latch, foot stopper, hydraulic
door closure of Dorma, brass hinges (parly panelled and partly
glazed) to be provided wherever required and will be measured
along with partitions area.
Finishing : Both side finished in 1.0 mm thk Laminate
5 Full Ht. Glass Partition & Door(MANAGER CABIN ):
sq.m 8
Providing top and bottom ENOX EAPS 32( interlocking glazing
profile) member along with 12mm glass ( toughened). The
item shal include door of 12mm toughned glass along with Top
patch EPF 601 AND EPF 602 Bottom patch, EPF 603, over panel
Pivot patch, along with s.s finish handles 300 mm D type, along
with EPF 735 Glass door lock with handles, EPF 752 verpanel
strike box L patch, complete as per drawing shown Complete
6 WALL PANELLING
sq.m 80
Providing and fixing 1.0 mm thk approved Laminate for
panelling on wall & column including skirting with joints and
grooves including 8mm thk. ply backing on 2" X 1" Aluminium
Sections at 1'6"-2'0" centres and teak wood moulding of size
38X45 mm as shown in detailed drawing and as directed. The
rate shall be inclusive of multi-coloured laminate including
patta, borders etc complete.
7 PILLAR AND WALL PANELLING
sq.m 20
Providing and fixing 18mm Plywood of approved make wood
through facia made to shapes at the walls / sides of column as
per site condition and instructions with necessary rawl plugs /
guttis and Hardwares. All visible surface to be laminated with
1.0mm thick laminates of approved make and shade. Finish as
per instructions including all fixing member, rawl plugs
adhesives etc. complete.
9 SOFT BOARD ( in partition)
sq.m 4
Providing & Fixing Soft Board panelling over framework of 25
mm x 18 mm T.W. Frame at 600 mm c/c with 6mm commercial
ply skining on top & 12mm thk. soft board with fabric finishing
over ply. Complete as per drawings & directions of the
Competent Authority, 25 mm x 12 mm T. W.Moulding on edges
(Basic Price of fabric Rs.250/- meter).
10 BOX FOR ROLLING SHUTTER.
sq.m 25
Providing and erecting boxing to cover the rolling shutter to be
made out of 19mm thk. ply for casing and openable shutters to
be finished with 3.0MM thk ACP laminate including hardware
such as hinges, locks etc.The box to be provided with 16
guage aluminium sheet fixed on 19mm thk ply. Complete as
per instructions.
11 MAIN DOOR : ( WITH FRONT PARTITION)
sq.m 30
Providing top and bottom ENOX EAPS 32( interlocking glazing
profile) member along with 12mm glass ( toughened). The
item shal include door of 12mm toughned glass along with Top
patch EPF 601 AND EPF 602 Bottom patch, EPF 603, over panel
Pivot patch, along with s.s finish handles 300 mm D type, along
with EPF 735 Glass door lock with handles, EPF 752 verpanel
strike box L patch, complete as per drawing shown Complete
12 LOW and FULL HT STORAGES
sq.m 20
Providing and fixing Full / Low height Storage as PER
SPECIFICATIONS.
Skeleton - made out of 19 mm. Thk ply at end verticals, top
and bottom and verticals 450mm to 600mm Centres as shown
in drawing and 6 mm thk back ply.
SHELVES - 19mm Thk. Plywood top and edges finished in
1.0mm thk. Laminate to accommodate file height removable
and supported on pins.
SHUTTERS-made out of 19mm thk. ply externally finished in
1.0mm thk. Laminate and Internally finished in 0.8 mm thk.
Laminate as shown or directed by Architect.
HINGES - Each shutter shall have 100mm long black oxidised
brass butt hinges. Mimimum 4 nos. hinges for Full height
Storage and 2 Nos. hinges for Low Height Storage to be
provided.
BOLTS - Flush tower bolts from inside at top and bottom to the
required shutters only - other shutters will have magnetic catch
fixed top and bottom.
LOCKS - of approved make 4 -lever brass body dead lock with
S.S. Key - master key for groups as required.
HANDLES - 100mm wide handles of brushed steel or c.p. brass
handle as approved by the Architect.
SKIRTING -100 mm x 9 mm thk plywood for skirting finished in
Laminate.
FACIA - 4" thk. wide Band finished in 1.0mm thk. Laminate.
BACK - Back side of storage to have 6mm thk. commercial ply
with polish finish.
Finishing :- All external surface finish with 1.0 mm thk
Laminate. In side invisible surface complete with putty and
painting 3 coats. All internal wood-work including back to have
coat of anti termite of approved make before polishing /
lamination.
13 CREDENZAS.
sq.m 2.1
Providing and erecting in position Credenza for the tables of
450mm deep or as indicated on the drawing to be made out
of 19mm thk. commercial ply & having 25 x 25mm t.w.
moulding with drawers and openable shutters below The
openable shutters to be made out of 19mm thk. ply with all
internal surfaces to be finished with putty and 3 coats of
paiting including using SS good quality fittings such as
hinges, ball catches, handles, locks etc. complete as per the
instruction of the bank. All credenzas will have 18mm thick
granite top finished to neat finish and the edges rounded off.
13a COUNTER CREDENZAS.
sq.m 2.1
Providing and erecting in position Credenza for the tables of
380mm deep or as indicated on the drawing to be made out
of 19mm thk. commercial ply & having 25 x 25mm t.w.
moulding with drawers and openable shutters below The
openable shutters to be made out of 19mm thk. ply with all
internal surfaces to be finished with putty and 3 coats of
paniting including using SS good quality fittings such as
hinges, ball catches, handles, locks etc. complete as per the
instruction of the bank. All credenzas will have 18mm thick
granite top finished to neat finish and the edges rounded off.
14 Table
Providing and supplying table for officers, r etc to be made
out of 19mm thk. ply with 1.0 mm thk. approved laminate
finish to the table externally and a coat of putty and three
coats of paitning to all the internal surfaces. The top of the
table to have t.w. moulding all around as per the directions
and instructions. The table to have heavy duty keyboard tray
on sliding channels, heavy duty CPU trolley. The necessary
hardware such as heavy duty automatic locking system
operable with single key for all the three drawers, ball
catches, foot rest, locks, handles, necessary hardware etc
complete. Necessary opening for electrical/computer wiring
to be provided as per the drawing and instructions of the
bank. Elevation of the table shall be as directed by bank on
site. All tables will have 18mm thick granite( basic rate `
280/sft) top finished to neat finish and the edges rounded
off.
The rate shall include the drawer unit with 3 nos of drawers
and 1 no of tray to be mounted on castors to be made out of
commercial ply and finished with 1.0mm thk laminate
externally &french polish internally including the necessary
hardware etc complete. The rate shall also include nylon
buffers between the ply & finished floor.
a Table :-1800x 750mm (table top size)
B Table :-1500x 750mm (table top size)
C RECEPTION TABLE in Curved profile with S.S studs and
curved glass
15 VOUCHER WRITING TABLE.
Providing and fixing voucher writing table consist of two box
type pedastal of each size 200mmx200mm and height
750mm made out of 18mm ply and 1 mm laminat with
provision of slit for garbage /waste paper bin. Conceled type
of door also to be included. on top of these two pedestal,
horizontal glass frame made out of 12mm in to piegeon hole
pattern to house various types of vouchers. length of the
glass frame to be about 900 mm. three nos of voucher
pegions to be made. Glass to be propertly jointed and
secured with ply wood work.
16 Notice Board
no
no
no
1
2
1
no
1
sq.m 2
Providing and fixing notice board 900 MM X 600 MM/size as
mentioned to be made out of 19mm thk. ply with 3" deep with
front glass shutter, 10mm thk. ply back covered with soft
board and felt cloth including polishing locks etc. finished as
per instruction of the Architect.
17 Gypsum Board False Ceiling:
Providing and Fixing Main Frame Suspended ceiling consisting
of fixing company made gypsteel channels of 27mm X 0.5 mm
thick having one flange of 20mm and another flange of 30mm
along with perimeter of the ceiling. Frame should be properly
anchored to the MS frame ( item no 8 ) . The suspending
Gypsteel intermediate channels of size 45mm x 0.55 mm thick
with two flanges of each from the soffit @1200 mm centers
with Gypsteel hangers of 25mm x 0.5mm thick fixed to soffit
with Gypsteel cleat and steel expansion Anchor fasteners and
to intermediate channel with Gypsteel nut and bolt. Ceiling
section of 0.5mm thickness having knurled wedge of 51.5 mm
and flanges of 26mm each with clips of 10.5mm fixed to the
int. channels with help of connecting clips in perpendicular
direction to the intermediate channels at 450mm center,
12.5mm thick tapered Edge Gypsum plaster board is to be
fixed with 25mm screws maintaining proper distance . Surface
to be finished with tape and plaster. Cost to include the cutout
provision for AC Grill, Light Fittings and any other gazetts as
Gypsteel support systems
sq.m 40
12.5mm India gypsum sheet with paint
sq.m 40
18 False Ceiling ( Armstrong )
Providing and erecting false ceiling of Mineral Fiber ceiling
Board Armstrong with clip on type panels with framework,
runners, suspenders from the existing ceiling as per the
manufacturers details and specification including fine fissured
tiles complete including making cut-outs for electrical fixtures,
AC diffusers, access etc complete as per the instructions of the
bank. Rate quoted should also holds good to carryout the
composite type of false ceilings with gypsum materials by
lowering the boards for housing of AC ducts. . tile size as
a Grid :- Microlook Suprafine XL 15mm grid Silhouette, with 'w' sq.m 120
edge angle.
b Tiles :- ANF RH 90 Armstrong
sq.m 120
20 PAINTING TO WALLS
sq.m 300
Painting with acrylic emulsion of best brand and best grade of
approved manufactureors like Asian,Berger etc with base coat
of putty, upper coat of ordinary enamel paint and top two coats
of acrylic emulsion
22 TEXTURE PAINT
sq.m 50
Spectrum texture paint spray bubble type with proper surface
preperation.All as per the instructions of the design in charge.
23 VERTICAL BLINDS
sq.m 20
Vertical Blinds of 75mm wide fabric as per specification and
brand. All as per the instructions of the design in charge. MAC
make
24 SERVER ROOM TABLE.
sq.m 2.5
Table top 2'0" wide . All made in 19mm plywood and 1mm
laminate for all vertical and inside areas and 1.0 mm thick
Laminate for the table top . Modesty panel should be at least
12mm thick. One Key board tray and One pedestal 16" wide
containing 2 draws and one flap door to be provided at every
4'6". All made in 19mm plywood and 1mm thick laminate even
for the internal areas of the plywood. all draws and key board
tray should be on telescopic channel and other hardware items
as specified. All the edges of the plywood to be covered with
12mm thick steam beech beading duly melamine polished. All
as per design and instructions of the design in charge.
25 COMPOSITE ALUMINUM CLADDING
sq.m
( FOR EXTERNAL CLADDING)
Providing and fixing in position COMPOSITE ALUMINUM SHEET
CLADDING ( thickness 3.0mm) EXTERIOR r grade of approved
shade.The composite panel sheet is to fixed to aluminum
sections as per structural support requirement/ manufacturer
reccomendation . The groove between two sheets shall be 2
mm which is to be sealed with silicone sealent as per
manufacturer specification. The rate shall include bending,
curving of the composite panel sheet to match the profile
shown on drawing. At edges composite panel is to be bend by
making V shaped groove on back side so that no joint is visible
in the front at bend juction. All inclusive Complete.
26 Posters/Wall papers
Providing supplying and designing on site posters on
LG/HANWA/BIRL3M flex, to be digitally printed on above
flex by solvent printing machine using original inks and
other consumables.
TOTAL
INTERIOR DECORATION WORKS.
sq.m 20
15
Download