Downloads
PUDLO CEMENT WATERPROOFING POWDER
A multi-component, single pack, waterproofing,
plasticising, permeability reducing, corrosion inhibiting
admixture. Outperforms any other admixture of its
kind.
hDB WATERSTOP
hDB WATERSTOP is a Hydrophilic Polyacrylate
Elastomeric (swellable rubber) type waterstop.
Designed for the integral sealing of construction joints
in cast-in place concrete. hDB WATERSTOP expands
upon contact with water to form a positive seal even in
saline conditions.
INSTAFLEX PU25 MASTIC
A high performance polyurethane single pack, multipurpose sealant. It is a one part, moisture curing, nonsag elastomeric sealant formulated to provide low skin
formation and fast cure.
INSTACEM Concrete Repair System
A specially formulated, pre-mixed cementitious
concrete powder. The material mixes readily with
water to produce a non-shrink, water-resistant repair
material that hardens to give a high strength product.
INSTACEM Primer Latex
A blend of acrylic polymer resins. The latex is applied to
previously prepared substrate concrete, blockwork,
brickwork, masonry or render before the application of
INSTACEM Special Concrete Products.
INSTASWELL Mastic
A one component, polyurethane based, solvent free,
hydro swelling mastic, supplied in cartridges and
aluminium cartridges, for the sealing of construction
joints.
INSTALASTIC
A liquid-applied, seamless, waterproof coating for
water retaining structures, submerged tunnels,
diaphragm walls, bridge deck waterproofing and a wide
variety of extreme service class concrete structures to
provide long service life, anti-carbonation, waterproof
construction.
PUDLO SC waterproofing admixture for selfcompacting concrete
PUDLO Self-Compacting Admixture (PUDLO SC) is an
extended Admixture specifically designed and
manufactured to produce exceptionally flowing
concretes, without segregation in Self-compacting
Concrete. Combining all the benefits of ultra-low
permeability and fine surface finish already achieved
using PUDLO CWP for over 100 years, PUDLO SC will
give consistent high workability and ease of use when
placing Self-compacting Concrete.
INSTAPRUF SELF SMOOTHING FLOOR-TOPPING
INSTAPRUF is a two pack, polymer modified,
cementitious based, water resistant, hard wearing,
self-smoothing seamless floor topping.
INSTACEM POLYMER WALL RENDER AND POINTING
INSTACEM Waterproof Render/ Mortar is a polymer
modified, cementitious mortar/plaster specifically
designed to produce a nonshrink, weather resistant,
high strength wall render/repair and pointing material.
INSTACEM Waterproof Render is factory made to BS
EN ISO 9001:2000 is user friendly (just add water) and
contains no toxic or harmful chemicals.
INSTACEM POLYMER FLOOR SCREED
A Polymer Floor Screed is a polymer modified, cement
based screed specifically designed to produce a nonshrink, weather resistant, micro fibre reinforced, high
strength flooring product. INSTACEM Polymer Floor
Screed is factory made to BS EN ISO 9001:2000 is user
friendly (just add water) and contains no toxic or
harmful chemicals.
DB 7 STAR HIGH FLOW GROUT
DB 7 Star High Flow Grout is a non shrink, very high
strength cementitious grout comprising of low alkali
high specific area Portland cements and other
cementitious binders and a system of compatible
admixtures to achieve high in service performance.
INSTACEM Mortar Underwater Powder
A blend of special cement powders, high quality graded
silica sand, and a unique combination of polymers and
admixtures. When mixed with water the powder
produces a mortar with a putty consistency which is
wash-out resistant and waterproof. The material
develops an early gain in strength and can be used
above or below the waterline.
INSTACEM P Protective coating
A high performance, acrylic based, hard wearing,
copolymer protective coating for concrete. INSTACEM
P is designed is to enhance the appearance of and
protect atmospherically exposed concrete structures
from aggressive elements, weathering and rain.
INSTACEM P is suitable for all types of concrete
structures including those exposed to harsh marine
environments. INSTACEM P is a component of the
David Ball Group’s INSTACEM system for concrete
repair and protection.