“ Where
is everything, but
is first ”
Introduction
The
DBS-6000, is a
mechanical seal that offers
the versatility to connect the
power cable of the pump
from the downhole to the
surface, quickly and safely,
minimizing rig time and total
operation cost.
Produced by:
Norma API 11S3
11S3 NORM
The
is fabricated
under the Recommended
Practice for Electrical
Submersible Pump
Installations
Produced by:
API 11S3 Norm
Recommendations
Service
Disconnected
and Motor
Control Panel
Transformer
Bank
VENTED
JUNCTION BOX
(OPTIONAL)
SEE 4.3.4 & 4.3.5
ELECTRICAL SEAL
FITTING AND VENT
Electric
Assembly
Wellhead
Ground
Rod
Prodcution String
GROUND
CONDUCTOR
Casing
Splice
Bands
Produced by:
American
Petroleum
Institute
Surface
Power
Cable
Downhole
Pump
Cable
Pumping
Assembly
SECURITY
ALL
PENETRATORS HAVE AN INTERN
GROUND WIRE THAT CONNECTS THE
WELLHEAD AND ALL ITS COMPONENTS.
ALL
PENETRATORS HAVE CERTIFY
SEALS OF SECURITY AND VENTILATION AS A
STANDAR PARAMETER OF MANUFACTURING.
Produced by:
THE
SURFACE CONNECTION
SYSTEM MAKES THE VENTING BOX IS
OPTIONAL.
Manufacturing Standars
The Seal Penetrator System
is fabricated under the following standars:
Explosion Proof NEMA 7 & 9
Class I, Divisions I & II Group D
Produced by:
Complete Assembly
Junction Box
Hanger
Double Body Seal
Penetrator System
6000
Produced by:
Versatility
The
DBS-6000 replaces other models of the market without
requiring any modification in the hanger.
The figure shows
a completation
with a “BIW”
Penetrator, this
can be replaced
by the SPS DBS6000 using a
Reducer Bushing
(Dummy
Mandrel)
SPS
JB-20
BIW
Penetrator
Reducer Bushing
(Dummy Mandrel)
SPS DBS-6000
Produced by:
Versatility
The design makes it unique in its style, because the
sealed system can be installed outside the hole.
SPS DBS-6000
Outside the well
Produced by:
Advantages
The threaded coupling system, is designed
so that once adjusted the upper with the
lower mandrel, the piston ensures sealing
elements on its seat, which gives a stamp
of quality to each driver individually.
Significantly minimizes the use of tools and
equipment installation.
Increases safety and reliability with the
implementation of the Guide Pre-seal,
used for cable alignment and primary seal.
Complete Installation of equipment is
between 30 to 40 minutes.
Produced by:
DBS-6000 on the Hanger
DBS-6000
(Open View)
DBS-6000
Installed with
Dummy
Mandrel
Produced by:
DBS-6000 Parts
O’ring (Viton)
Upper Mandrel
O 'ring (Viton)
Bearing
Main Seals
Piston
Lower Mandrel
Pre-Seal Guide
Produced by:
Neck Transition
Wellhead Completation
Caja de Empalme
Cables de Potencia
Colgador
Penetrador DBS 6000
Produced by:
Installation of Connections
SPS Surface
Conduit J-Box
(Open View)
Conductor
Ground Wire
Produced by:
Installation of Connections
SPS Surface
Conduit J-Box
(Open View)
Splice Connector
Produced by:
Installation of Connections
SPS Surface
Conduit J-Box
(Open View)
Produced by:
Splice Boots
Surface Connection
Drain and
Vent
Produced by:
Commercial Information
Other Products:
Manufacturer
Wellheads and Christmas Trees
Contact information
Manufacturer & Sales
Hector G. Ahow
President
Cra. 31 # 16-258 – Medellín
Tel.: 57 (4) 583 8764
(57) 315 871 9278
Fax: 57 (4) 583 87 64
E-mail:
hector@ahow.com.ve
Web Page:
www.ahow.com.ve