R_MOD_14-Basic_Network_Configuration_for_File

Basic Network Configuration for File
Upon completion of this module, you should be able to:
• Configure Data Mover network devices
• Implement DNS and Time Services
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
1
Basic Network Configuration for File
Lesson 1: Data Mover Network Devices
During this lesson the following topics are covered:
• Network device speed and duplex settings
• IP interface for client access
• Routing table
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
2
Modifying and Displaying Configuration
Settings > Network > Settings For File
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
3
Listing Network Devices
Settings > Network > Settings for File > Devices
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
4
Duplex & Transmission Speed
• Duplex setting
 Preferred setting is auto (Default)
 Best practice setting is auto for GigE connections
• Transmission Speed
 Defaults to auto
 Use maximum speed supported on the network between the VNX
and the client
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
5
Setting Speed/Duplex
Device Properties to set Speed/Duplex
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
6
IP Address Configuration
• Interfaces tab > Create
• Required Parameters
 IP Address
 Subnet mask
 Broadcast address
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
7
Displaying IP Configuration
Settings > Network > Settings For File > Interfaces
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
8
IPv6 Support
• VNX supports IPv6 IP addresses
• More addresses
• Better security
Roll security into the protocol
• IPv6 address example:
2620:0000:0170:0062:021B:D5FF:FE25:7082
Network
Copyright © 2014 EMC Corporation. All Rights Reserved.
Subnet
Interface ID
Basic Network Configuration for File
9
Unisphere: Control Station IPv6
System > Control Station Properties
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 10
Data Mover Routing
• Routing table of a Data Mover directs
outgoing network traffic via, both external
and internal gateways
 Routes to a host
 Routes to a network
• Data Mover routing table can contain 3
types of routes
 Directly connected
 Static
 Dynamic
• Packet Reflect
 Reply to network client requests
 Route and ARP tables are not examined
Multiple Interfaces
on a Network
When more than one IP
interface are on the same
network, the first interface
configured will be the
default path out of the Data
Mover.
Example: Interface “A”
iscreated on a Data Mover,
then interface “B”. All
resource queries (e.g. DNS)
will go out through interface
“A”.
 No need to determine the route to
send the reply packets
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 11
Viewing Data Mover Routing Information
Settings > Network > Settings For File > Routes
Default
Gateway:
0.0.0.0
Route to
Network:
192.168.64.0
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
12
Configure Default Gateway
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 13
Deleting Routes
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 14
Basic Network Configuration for File
Lesson 1: Summary
During this lesson the following topics were covered:
• Network device speed and duplex settings
• IP interface for client access
• Routing table
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
15
Basic Network Configuration for File
Lesson 2: Implement DNS and Time Services
During this lesson the following topics are covered:
• Data Mover DNS Configuration
• Time Services (NTP and SNTP)
• Implement Time Services for a Data Mover
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
16
Displaying DNS Settings
Settings > Network > Settings For File > DNS
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 17
Configuring a Data Mover for DNS
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 18
Time Services Overview
• Data Mover NTP client
 Synchronization of the system clock with an NTP or SNTP server
• NTP
 Sophisticated algorithms for time correction and maintenance to
allow time synchronization with an accuracy of about a millisecond
• SNTP
 Subset of NTP for use in environments with less stringent
synchronization and accuracy requirements
• To the client, NTP or SNTP are indistinguishable
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
19
Initializing Time Services on a Data Mover
System > Hardware > Data Movers
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File 20
Basic Network Configuration for File
Lesson 2: Summary
During this lesson the following topics were covered:
• Data Mover DNS Configuration
• Time Services (NTP and SNTP)
• Implement Time Services for a Data Mover
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
21
Module Summary
Key points covered in this module:
• Recommended Data Mover speed/duplex setting is 'auto'
• Use Data Mover time services to synchronize with Windows
and Unix/Linux environments
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
22