Latching Relay

advertisement
Latching Relay
1/2
1 make contact
Data sheet
A1
~
14
A2
~
13
Item-No.
Description
Latching relay AC 230 V / 16 A, 1 make contact
789-570

Contact current 16 A
Technical Data

Bistable, pure mechanical storage.

Safe electrical isolation in acc. with EN 61140

Suitable for continuous operation (module assembly).

Low-noise switching
Input:
Input nominal voltage UN
Input voltage range
Current input at UN
(coil 20 °C)
Minimum switch-on time
Minimum break time
Coil control
Glow lamps parallel
to the push button
Type of load
Max.load
Incandescent lamp load
Fluorescent lamp test in
Duo-circuit
1500 W
Electronic ballasts*
20 x 58 W
series compensated
10 x 58 W
*
When using electronic ballast a make current
40-60 times higher might occur.
Output:
Contact material
Recommended min. load
Max. switching voltage
Max. switching current
Max. continuous current
Max. switching power
(resistive)
Operation at normal rating
Max. operating frequency
With load / without load
Dielectric strength
Contact/coil (AC, 1 min.)
Nominal voltage acc. to
EN 60664-1
Mechanical life
Protection
Note: Inductive loads have to be attenuated by
an appropriate protective circuit in order to
protect relay coils and contacts!
WAGO Kontakttechnik GmbH & Co. KG
Subject to design changes
21.05.2012 / d07890570_00000000_0en.doc
Postfach 2880 • D-32385 Minden
Hansastr. 27 • D-32423 Minden
Pack.-unit
pcs
Tel.:
Fax.:
1
AC 230 V / 50/60 Hz
UN -10% ...+10 %
80 mA
40 ms
180 ms
pulse operation
10 mA at AC 230 V
AgSnO2
10 mA / 10 V
AC 250 V
50 A (20 ms)
16 A
AC 4000 VA
100 % continuous duty
-1
6 min / 5 s
-1
4 kV eff.
250 V / 4 kV / 2
5
1 x 10 switching operations
circuit-breaker
Max. 16 A B-Characteristic
05 71 / 8 87-0
E-Mail:
05 71 / 8 87-169 Web:
info@wago.com
http://www.wago.com
Latching Relay
2/2
1 make contact
Data sheet
General Data:
Ambient operating temperature -25 °C...+40 °C
Storage temperature
-40 °C...+85 °C
Dimensions (WxHxD)
(17.5x55*x90) mm / (0.69x2.17*x3.54) in
* from upper edge of DIN 35 rail
Wire connection
CAGE CLAMP®
2
0,08-2,5 mm / AWG 28-14
Stripped length
5-6 mm / 0.22 in
Standards / prescriptions
EN 60664-1
Accessories:
Push-in type jumper bars,
789-112
IN 16 A
blank, 13-fold
Cut requiered length
Schematic
13 13
A1
A1
A2
13
14
A2
14 14
Connection example
L1
T1
T2
A1
14
A2
13
N
Assembly notes
!
When inserting push in type jumper bar mind
touchproof protection.
WAGO Kontakttechnik GmbH & Co. KG
Subject to design changes
21.05.2012 / d07890570_00000000_0en.doc
Postfach 2880 • D-32385 Minden
Hansastr. 27 • D-32423 Minden
Tel.:
Fax.:
05 71 / 8 87-0
E-Mail:
05 71 / 8 87-169 Web:
info@wago.com
http://www.wago.com
Download