Quick View Guide

J6

Copyright © 2015 QIGI

All Rights Reserved

No part of this manual may be reproduced or forwarded in any form or by any means without prior written consent of QIGI.

Statement

QIGI reserves the right to revise this document or withdraw it at any time without prior notice.

Safety Precautions

Please read these simple guidelines. Not following them may be dangerous or illegal. For further information, see the section of

“Warnings and Precautions”.

Do not switch the phone on when mobile phone use is prohibited or when it may cause interference or danger.

Do not place your phone and its accessories in containers with strong electromagnetic field.

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

Hospitals or health care facilities may be using equipment that could be sensitive to external radio frequency energy.

Follow any regulations or rules in force.

Do not use the phone at a refueling point. Do not use near fuel or chemicals.

Follow any restrictions. Wireless devices can cause interference in aircraft.

Keep the phone and all its parts, including accessories, out of the reach of small children.

Use only approved batteries and chargers. Disconnect the charger from the power source when it is not in use. Do not leave the battery connected to a charger for more than a week, since overcharging may shorten its lift.

Please remove the battery only after the phone is switched off normally, otherwise it could cause unpredictable damage for the phone.

Only qualified personnel should service the phone or install the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty applicable to the device.

Mobile phone appearance

Boot: press and hold the power button for 3 seconds.

Off: press and hold the power button for 3 seconds, pop-up mobile phone options dialog box, select the shutdown menu item.

No

1

2

3

4

5

Button Name

Menu Key

Home Key

Back key

Side key

SIM 1 card slots

Help

Press to pop-up menu

Click here to return to the idle screen

Click here to return to previous level interface

You can adjust the volume

Should be inserted into the standard

SIM card

1

7

8

9

6

10

Reset

ON / OFF button

T-FLASH card slot

SIM 2 card slots camera key

11 Headset interface

12

13

USB interface

Camera

Use, such as abnormal must (reset button and switch key) while pressing 5 seconds after the system reset, press the switch button to boot

Press the button on / off

例如,如果机器死机,可以 reset+power 5S ,进入 reset 状态,如

Insert the Micro SIM card

果按下的时间 >=6s ,则机器会重启。

Long press this button directly into the camera

You can insert Headset

The data line jack, charging port

Camera and camera lens

Screen icon

Icon Help

Battery capacity

Wifi hotspot alarm clock

Data transfer mode

WIFI synchronous download upload

Icon Help

Silent mode

Signal strength

Flight mode

Open Bluetooth

Bluetooth data transmission

Note: placing heavy objects on the mobile phone may damage the screen and mobile phone.

2

Battery Charging

This product is the built-in battery charging, please be sure to use the original charger and data lines.

When the electricity is low, there will be sound, and prompts the lack of electricity;

When the charge is further reduced when the product once again issued a prompt sound, and then shut down.

Start using this product

Install the SIM card

1. Find SIM 1 card slots installed, open the SIM 1 card slotshaving. As shown in figure 1:

Figure 1

Note: if you want to install or remove the SIM card, please must first turn off the phone and cut off all power supply connected with a mobile phone.

2. The SIM card inserted into the card slot corresponding tothe SIM

3

card slot, having closed. As shown in figure 2:

Figure 2

Install the SIM 2/T-FLASH card

1.

Find the SIM 2/T-FLASH card slot installed, open the card slot. As shown in figure 3:

Figure 3

2. SIM 2/T-FLASH card inserted into the card slot corresponding to the

4

slot, having closed. As shown in figure 4:

Figure 4

Note: This product has eight grade waterproof function.

After the installation of the SIM/T-FLASH card, please put all the card slot having closed; lest the waterproof function failure.

Dial

1.

Standby mode, click on the interface dial icon to enter the dial pad.

2.

Click the icon to hide the dial pad dial pad interface, view call logs in the contact's number, you can also click directly on the dial pad interface inputs need to dial the phone number.

3.

Click the icon to make a call to allocate the call.

5

Basic functions

Enter the phone number directly

1. Standby mode, click on the screen to enter the dial pad dial icon, click on the digital input phone number.

2. If you enter a wrong character, click on the delete icon to delete the dial pad.

3. To end the call or cancel the call, click the icon to hang up the phone hang up.

Lock Products

Lock the product, the interface will be shut down, and the product will enter sleep mode. This can avoid accidentally touching the interface, but can also save battery power. When not using the product, press the on / off button, the product locked. Such as setting the lock screen time, then the standby time to the rear of the product will automatically lock screen.

Unlocking the product

Press the power button wake up the product. Press and hold the middle of the screen with a finger slide to the right of the screen lock icon to Unlocked.

Sends a document to the product

You can use a variety of documents to take with you. You can also listen to music, or browse your most cherished photos and videos collection.

1.

Use the included USB cable to connect the product to the computer.

2.

Pull-down status bar appears when the USB is connected, click to open the USB storage device, and then click OK.

3.

Computer will argue that this product removable disks. Navigate to the removable disk, and then open the disk.

4.

Copy the document to the memory card. After copying the document, in accordance with the requirements of your computer's operating system, uninstall the product, and then in a safe exit.

6

5.

Interrupt the connection between the product and the computer.

Restore factory settings

You want to re-set this product? If you want the product to someone else, or just want to start from scratch, you can perform a factory reset of the product. You must be careful to face this step because Resetting the product will erase all data, including the previously downloaded and installed any application. Resetting the product will be restored to you first open the product's initial state.

Reset the product by setting

1.

In the main menu, tap Settings> Backup & reset> Restore factory settings.

2.

Points to restore factory settings> Point Reset phone> Point Clear

All contents> phone will automatically shut down and restart.

Safety Warnings and Precautions

Electronic Equipment

In the vicinity of electronic devices using high-precision control , turn off the phone , otherwise it may cause electronic equipment to malfunction. may be affected by the phone equipment: hearing aids, pacemakers, fire alarms, automatic doors and other automatic control equipment. The use of electronic medical device, users should confirm the effects of radio waves on their own equipment and services to the center of the instrument.

Pacemaker manufacturers recommend that the distance between the phone and a pacemaker to keep at least 15 cm in order to avoid potential interference with the pacemaker . When carrying the phone , it should not be placed in a breast pocket ; should use the ear opposite the pacemaker to the ear , in order to minimize the potential for interference.

Medical establishments

Do not bring cell phones to the operating room , intensive care unit (ICU) or coronary care unit (CCU).

Prohibit the use of mobile phones in medical establishments , follow the instructions and rules of the place running.

Please note that the tone, volume, vibration settings of the phone, so as

7

not to impact on heart disease patients.

Explosive areas

In explosive areas , shut down , do not remove , install the battery , charging the battery or use the phone in order to avoid an explosion or fire. Explosive areas are:

Stations ;

Fuel zones ( such as: the ship's deck under the cabin ) ;

Fuels or chemical products transportation and storage facilities ;

( Granules, dust, metallic powders such ) region ; chemicals or particles contained in the air

Explosion hazard marked areas ;

Have to "turn off two-way radio " sign area ;

Generally recommended that you turn off the area , such as automobile engine.

Traffic Safety

When driving , please observe the relevant provisions of the geographical location or country . Do not use a cell phone while driving a car , so as not to interfere with safe driving , causing an accident. Keep the phone while driving on the phone bracket , do not place the phone on the seat , or in the collision , where possible loose when the brakes when the vehicle is parked in a safe place after , before they can use the phone.

If the phone has a speakerphone function , or equipped with a headset, or a car with a car handsfree device, in case of emergency , use these features, the device or make emergency calls for help .

Do not place the phone on the car insurance after balloon can reach the top or airbag deployment zone , or otherwise ruptured when the air bag inflates , the phone would be a strong force , may cause serious harm to the owners .

When flying, the airline should comply with the relevant rules and regulations. In the vicinity of the aircraft or aircraft, please turn off the phone and remove the battery, prohibit the use of mobile phones in the airport area, turn off the phone, so the phone's wireless signal interference aircraft control signal.

Storage Environment

Keep the phone away from magnetic devices ( such as: magnetic cards and floppy disks ) , cell phone radiation may erase the information stored on the magnetic device.

Do not use the phone, battery and charger placed in an appliance with a

8

 strong electromagnetic field , such as the induction cooker and microwave , as this may lead to circuit failure , fire, or explosion.

Do not use high-temperature region , the temperature is too low area , place the phone , battery and charger , as this may cause the phone , battery and charger failure , fire, or explosion.

When charging the battery , the battery should be maintained at an ambient temperature between 0

and 45

. Battery Storage temperature maintained between -20 ℃ and 60 ℃ . If the battery in hot or cold areas , it may reduce the battery capacity and service life. When the temperature is below 0 ℃ , Battery performance is particularly limited.

Pins , etc. Do not place sharp metal objects near the handset, magnetic handset will suck these objects that could cause injury when using the phone .

Do not make the phone , battery and charger subjected to strong shock or vibration , so as not to lead to battery leakage , mobile phone failure , overheating, fire or explosion.

Do not place the phone in your pocket in the back of your trousers or skirt , to avoid damage to the phone when you sit down.

Children's Health

Keep the phone , battery and charger away from children 's reach , do not allow children under the unsupervised use of mobile phones , batteries and chargers.

Do not allow children to mouth with battery because the electrolyte may cause poisoning.

Do not allow children access to the phone's small parts, so children who otherwise might swallow parts caused by suffocation, blockage of the esophagus and other injuries .

Operating environment

Your phone, battery and charger are not water-resistant , when used , keep it dry. Do not let the phone , battery, charger and contact with water vapor ; or cell phone with wet hands , so as not to cause the device to short-circuit failure due to corrosion caused by electric shock.

Do not use the phone in dusty , wet, dirty , or near magnetic fields , so as not to cause the phone's internal circuitry failure.

When the phone contact with the ear , do not turn on or off , so as not to affect human health.

To comply with the provisions of RF leakage , when you wear a phone or using the phone data features , please keep a distance from the antenna and the body of at least one inch ( 2.5 cm ) .

9

If you are using a mobile game for a long time , and cause physical discomfort ( such as: epilepsy , vertigo ) , please seek help immediately to your doctor.

When you are using a hands-free phone function , do not phone to your ear , so as not to sound too much damage hearing.

If your phone has an infrared interface, you do not see the interface with an optical amplifier.

If your phone has a camera function , do not flash too close to you or someone else 's eyes.

If your phone is equipped with a stylus pen , touch pen is carefully drawn so as not to scratch the surface of the phone or screen.

When a thunderstorm , do not use the phone while charging ; or outdoor use mobile phones to avoid being struck by lightning or other injury .

Do not touch the antenna during a call , touch the antenna affects call quality and make use of the phone's power higher than normal power required , thus shortening talk time and standby time.

Phone signal interference may affect the adjacent TV, radio or computer.

Please comply with RF exposure requirements of international norms , the use of the designated cell phone accessories.

When using the phone , please comply with the relevant laws and regulations, and respect others' privacy and legal rights.

Cleaning and maintenance

Before cleaning and maintenance , turn it off , if this Shihai connected to the charger , you will need to unplug the charger from the wall outlet , and disconnect the charger from the phone , to avoid electric shock , short-circuit the battery or charger .

Do not use chemicals ( such as: alcohol, benzene , etc. ) or chemical lotion or scrub cleaners , wipe the phone or charger may damage the unit or cause a fire. Available damp , soft, anti-static cloth.

Do not scratch or altered cell phone case , otherwise the paint off may cause human allergies , if an allergic reaction occurs , you need to immediately stop using the phone and seek help your doctor.

Clean the dust on the power plug , the plug and kept dry to avoid fire.

If the phone, its parts and accessories is not working properly , please contact your nearest authorized service agencies, personnel service center will help.

Do not disassemble the phone and accessories , only authorized institutions are allowed to repair the phone.

10

Environmental Protection

Please comply with the phone packaging materials, exhausted batteries and old phone local laws deal with , and try to support the recall . Do not dispose of trash in the phone or the battery or ignition sources in order to avoid an explosion.

This device complies with Directive 2002/95/EC on the restriction of use of certain hazardous substances in electrical and electronic equipment requirements.

Emergency calls

 In case of emergency, if the phone is switched on and in a service area , you can use the phone for emergency calls. However , because they can not guarantee that all of the network can join, so in case of emergency, the phone can not be used as the sole contact.

Use battery

Use only approved batteries phone manufacturer , do not use the wrong type of battery , it may cause an explosion.

Do not throw batteries into the fire, otherwise it will cause the battery to ignite or burst.

Do not place metal objects , keys, jewelry and other conductors and poles of the battery and docking, or contact with the battery 's end , so as not to cause the battery to short circuit, overheating and physical damage caused by the battery ( such as burns ) .

Do not disassemble the battery or directly solder the battery poles , in order to avoid battery leakage , overheating , fire or burst.

If the battery leaks , smoke or odor should immediately stop using it and keep it away from open flame and the human body, in order to avoid fire or burst wounding. In ensuring the safety of the situation by a qualified maintenance treatment .

Battery is not fully charged after delivery , please charge for at least 2 hours before using .

If the battery fluid gets on skin or clothing , immediately rinse with water, so as not to damage the skin .

If the battery fluid splashing into the eyes , do not rub your eyes , otherwise it would visually impaired shall immediately rinse with clean water , and to the hospital for medical treatment .

If the charging or battery storage process and found that the deformation , discoloration, abnormal heat , etc. , remove the battery immediately , no longer continue to use, otherwise it will cause the battery to leak, overheat , burst or fire.

11

When the battery is not correctly loaded in the phone , do not squeeze the battery to avoid battery leakage or rupture.

Do not remove the battery in the boot state .

If not using the battery, the battery charging stand at room temperature.

Use charger

Use only manufacturer-approved mobile phone charger , do not use the wrong type of charger , or it may cause a malfunction or explosion.

Do not short-circuit the charger in order to avoid equipment failures, smoke or fire.

If the power cord is damaged ( eg : exposed wires , broken ) , or the connection plug is loose , do not continue to be used , to avoid electric shock , short circuit or fire charger .

Do not place the container with water or other liquids beside charger , the liquid may cause leakage or other malfunction after entering the charger.

Do not charge in a dusty , humid environment , and the power cord is not close to the heating vessel .

Before charging , make sure the charger plug is properly inserted into the power outlet. If the charger plug is inserted incorrectly, you may cause electric shock, fire or explosion phone or battery . The need to cut off the power when charging is finished , unplug the power cord Erwu Chela .

Charger specifications require the use of an AC voltage, if the use of other voltage may cause fire or malfunction .

Charger ban put heavy objects on the power cord , do not damage , alteration, pull on the power cord , as this may cause electric shock or fire.

Do not touch with wet hands is charging power plug , power cord , charger, or it may cause an electric shock .

If liquid such as water gets into the charger , the charger immediately unplug the power cord from the outlet to prevent overheating , fire or other failure .

Using a USB data cable

When using the USB data cable to connect the phone and a personal computer , connect the mobile terminal , and then connect the PC side .

In the communication process cell phones and personal computer, plug the USB cable is strictly prohibited .

Please operate in strict accordance with the above requirements , it may cause damage to the phone or computer equipment .

12

J6

13