HP Pavilion dv5 Entertainment PC
Maintenance and Service Guide
© Copyright 2008 Hewlett-Packard
Development Company, L.P.
Athlon and Turion are trademarks of
Advanced Micro Devices, Inc. Bluetooth is a
trademark owned by its proprietor and used
by Hewlett-Packard Company under license.
Intel and Core are trademarks of
Intel Corporation in the U.S. and
other countries. Microsoft, Windows, and
Windows Vista are U.S. registered
trademarks of Microsoft Corporation.
SD Logo is a trademark of its proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: August 2008
Document Part Number: 469060-001
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ................................................................................................................................... 7
Display and top components ............................................................................................... 7
Buttons, fingerprint reader, and speakers ............................................................................ 9
Keys ................................................................................................................................... 11
TouchPad .......................................................................................................................... 12
Front components .............................................................................................................................. 13
Rear components ............................................................................................................................... 14
Right-side components ....................................................................................................................... 14
Left-side components ......................................................................................................................... 15
Bottom components ........................................................................................................................... 16
3 Illustrated parts catalog
Service tag ......................................................................................................................................... 17
Computer major components ............................................................................................................. 18
Display assembly components ........................................................................................................... 27
AntiGlare display assembly spare parts ............................................................................ 27
BrightView display assembly spare parts .......................................................................... 28
Plastics Kit .......................................................................................................................................... 30
Cable Kit ............................................................................................................................................. 31
Mass storage devices ......................................................................................................................... 32
Miscellaneous parts ............................................................................................................................ 34
Sequential part number listing ............................................................................................................ 35
4 Removal and replacement procedures
Preliminary replacement requirements ............................................................................................... 44
Tools required .................................................................................................................... 44
Service considerations ....................................................................................................... 44
Plastic parts ....................................................................................................... 44
Cables and connectors ..................................................................................... 45
Drive handling ................................................................................................... 45
v
Grounding guidelines ......................................................................................................... 46
Electrostatic discharge damage ........................................................................ 46
Packaging and transporting guidelines ............................................. 47
Workstation guidelines ..................................................................... 47
Equipment guidelines ....................................................................... 48
Unknown user password ................................................................................................... 49
Component replacement procedures ................................................................................................. 50
Service tag ......................................................................................................................... 50
Computer feet .................................................................................................................... 51
Battery ............................................................................................................................... 52
Webcam/microphone module ............................................................................................ 53
Optical drive ....................................................................................................................... 55
TV tuner module ................................................................................................................ 57
RTC battery ....................................................................................................................... 59
Memory module ................................................................................................................. 60
Hard drive .......................................................................................................................... 62
WLAN module .................................................................................................................... 65
Switch cover and keyboard ................................................................................................ 69
Power button board ........................................................................................................... 73
Speaker assembly ............................................................................................................. 74
Bluetooth module ............................................................................................................... 75
Display assembly ............................................................................................................... 76
Top cover ........................................................................................................................... 84
Modem module .................................................................................................................. 87
Audio/infrared board .......................................................................................................... 89
USB board ......................................................................................................................... 90
System board ..................................................................................................................... 92
TV tuner module cable ....................................................................................................... 94
Modem module cable ........................................................................................................ 95
Power connector cable ...................................................................................................... 96
Fan/heat sink assembly ..................................................................................................... 98
Processor ......................................................................................................................... 102
5 Setup Utility
Starting the Setup Utility ................................................................................................................... 104
Using the Setup Utility ...................................................................................................................... 105
Changing the language of the Setup Utility ..................................................................... 105
Display system information .............................................................................................. 105
Restoring default settings in the Setup Utility .................................................................. 106
Exiting the Setup Utility .................................................................................................... 106
Setup Utility menus .......................................................................................................................... 107
Main menu ....................................................................................................................... 107
Security menu .................................................................................................................. 107
vi
System Configuration menu ............................................................................................ 107
Diagnostics menu ............................................................................................................ 108
6 Specifications
Computer specifications ................................................................................................................... 109
15.4-inch, SXGA+ display specifications .......................................................................................... 110
15.4-inch WXGA display specifications ............................................................................................ 111
Hard drive specifications .................................................................................................................. 112
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer ............................................... 113
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications ............................... 114
System DMA specifications, AMD .................................................................................................... 115
System DMA specifications, Intel ..................................................................................................... 115
System interrupt specifications, AMD discrete graphics .................................................................. 116
System interrupt specifications, AMD UMA graphics ....................................................................... 117
System interrupt specifications, Intel ................................................................................................ 118
System I/O address specifications, AMD ......................................................................................... 119
System I/O address specifications, Intel .......................................................................................... 121
System memory map specifications, AMD discrete graphics ........................................................... 123
System memory map specifications, AMD UMA graphics ............................................................... 124
System memory map specifications, Intel ........................................................................................ 125
7 Screw listing
Phillips PM2.5×7.0 screw ................................................................................................................. 127
Phillips PM2.5×6.0 captive screw ..................................................................................................... 131
Phillips PM2.0×4.0 screw ................................................................................................................. 132
Phillips PM2.0×4.0 screw ................................................................................................................. 135
Phillips PM2.5×4.0 screw ................................................................................................................. 136
Phillips PM3.0×4.0 screw ................................................................................................................. 138
Phillips PM2.5×6.0 screw ................................................................................................................. 139
Phillips PM2.0×10.0 captive screw ................................................................................................... 140
8 Backup and Recovery
Recovering system information ........................................................................................................ 142
Creating recovery discs ................................................................................................... 143
Backing up your information ............................................................................................................. 144
When to back up .............................................................................................................. 144
Backup suggestions ......................................................................................................... 144
Using system restore points ............................................................................................ 144
When to create restore points ......................................................................... 145
Create a system restore point ......................................................................... 145
Restore to a previous date and time ............................................................... 145
Performing a recovery ...................................................................................................................... 146
Recovering from the recovery discs ................................................................................ 146
vii
Recovering from the dedicated recovery partition (select models only) .......................... 146
9 Connector pin assignments
1394 ................................................................................................................................................. 147
Audio-in (microphone) ...................................................................................................................... 147
Audio-out (headphone) ..................................................................................................................... 148
External monitor ............................................................................................................................... 148
HDMI ................................................................................................................................................ 149
RJ-11 (modem) ................................................................................................................................ 150
RJ-45 (network) ................................................................................................................................ 150
Universal Serial Bus ......................................................................................................................... 151
10 Power cord set requirements
Requirements for all countries or regions ......................................................................................... 152
Requirements for specific countries or regions ................................................................................ 153
11 Recycling
Battery .............................................................................................................................................. 154
Display .............................................................................................................................................. 154
Index ................................................................................................................................................................. 160
viii
1
Product description
Category
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
Product Name
HP Pavilion dv5 Entertainment PC
√
√
√
Processors
AMD processors:
AMD Turion™ Ultra Dual-Core 35W
ZM-86 2.40-GHz with 2-MB L2 cache
√
√
AMD Turion Ultra Dual-Core 35W ZM-82
2.20-GHz, with 2-MB L2 cache
√
√
AMD Turion Ultra Dual-Core 35W ZM-80
2.10-GHz, with 2-MB L2 cache
√
√
AMD Turion Dual-Core 35W RM-70
2.00-GHz with 1-MB L2 cache
√
√
AMD Athlon™ X2 Dual-Core 35W QL-60
1.90-GHz with 1-MB L2 cache
√
√
Intel® processors:
Chipset
Intel Core™2 Duo T9600 2.80-GHz with
6-MB L2 cache and 1066-MHz front side
bus (FSB)
√
Intel Core2 Duo T9400 2.53-GHz with 6MB L2 cache and 1066-MHz FSB
√
Intel Core Duo T8600 2.40-GHz with 3MB L2 cache and 1066-MHz FSB
√
Intel Core Duo T8400 2.26-GHz with 3MB L2 cache and 1066-MHz FSB
√
Northbridge: AMD M770 chipset, ATI
Radeon HD 3450 graphics
√
Northbridge: AMD M780G chipset, ATI
Radeon HD 3200 graphics
Southbridge: AMD SB700
√
√
√
Northbridge: Intel PM45
√
Southbridge: Intel ICH9M
√
1
Category
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Graphics
ATi Mobility Radeon HD 3450 with 256
MB of discrete graphics subsystem
memory (32 MB × 16 DDR2 × 4 PCs)
√
Unified memory architecture (UMA) with
shared video memory:
●
Up to 358 MB of graphics
subsystem memory on computer
models equipped with 2048 MB or
more of main system memory
●
Up to 251 MB of graphics
subsystem memory on computer
models equipped with 1024 MB
●
Memory size is dynamic change
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
√
Discrete graphics subsystem memory
Panels
Memory
2
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
√
●
GeForce 9650M GT, Nvidia NB9PGS with 512 MB (32 MB × 16 DDR2
×8 PCs)
●
GeForce 9300M GS, Nvidia NB9MGEB with 256 MB
(32 MB × 16 DDR2 × 4 PCs)
●
15.4-inch, WSXGA+ (1680 × 1050) √
AntiGlare
√
√
●
15.4-inch, WSXGA+ (1680 × 1050) √
BrightView
√
√
●
15.4-inch, WXGA+ (1440 × 900)
AntiGlare
√
√
√
●
15.4-inch, WXGA+ (1440 × 900)
BrightView
√
√
√
●
AntiGlare glass panel cover
support
√
√
√
●
Support for lighted logo on
display enclosure
√
√
√
●
Typical brightness 200 nits
√
√
√
2 SODIMM slots
√
√
√
Customer-accessible/upgradable
√
√
√
PC2-6400, 800-MHz, DDR2
√
√
√
Dual-channel support
√
√
√
Chapter 1 Product description
Category
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
√
√
Supports all Serial ATA (SATA) 9.5-mm, √
2.5-inch hard drives
√
√
Supports up to 2 hard drives
√
√
√
Support for Accelerometer hard
drive protection
√
√
√
Support for solid-state drive (SSD) on
dual hard drive configurations, with SSD
set as the primary drive
√
√
√
Dual hard drive configurations:
√
√
√
√
√
√
12.7-mm tray load
√
√
√
Parallel ATA
√
√
√
Supports up to 4096 MB system memory √
Hard drives
●
4096-MB total system memory
(2048 MB × 2, dual-channel)
●
3072-MB total system memory
(2048 MB × 1 + 1024 × 1)
●
2048-MB total system memory
(1024 MB × 2, dual-channel)
●
2048-MB total system memory
(2048 MB × 1)
●
1024-MB total system memory
(512 MB × 2, dual-channel)
●
1024-MB total system memory
(1024 MB × 1)
●
640-GB (320-GB, 5400-rpm × 2)
●
500-GB (250-GB, 5400-rpm × 2)
●
320-GB (160-GB, 7200-rpm × 2)
●
320-GB (160-GB, 5400-rpm × 2)
●
64-GB SSD + 320-GB, 5400-rpm
Single hard drive configurations:
Optical drives
●
320-GB, 5400-rpm
●
250-GB, 5400-rpm
●
160-GB, 7200-rpm
●
160-GB, 5400-rpm
●
120-GB, 5400-rpm
3
Category
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
Fixed (1 screw for removal)
√
√
√
Support for the following optical drives:
√
√
√
Low-light VGA camera
√
√
√
Fixed (no tilt)
√
√
√
Activity LED
√
√
√
640 × 480 by 24 frames per second
√
√
√
Microphone
2 omnidirectional microphones, dual
array with appropriate software
(supports beam forming, echo
cancellation, and noise suppression)
√
√
√
Audio
HD Audio (IDT)
√
√
√
Integrated subwoofer
√
√
√
Supports Microsoft Premium
Requirements
√
√
√
Pavilion-branded Altec Lansing
speakers
√
√
√
56K V.92 data/fax modem
√
√
√
Supports all world-wide certification
requirements
√
√
√
Integrated Realtek 10/100/1000 network
interface card (NIC)
√
Webcam
Modem
Ethernet
●
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive with
LightScribe
●
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive
●
Blu-ray Disc ROM Drive with
SuperMulti DVD±R/RW DoubleLayer
Integrated Realtek 10/100 NIC
Wireless
√
Integrated wireless local area network (WLAN) options by way of wireless module:
Atheros AR9280 802.11a/b/g/n
√
√
Broadcom 4321 802.11a/b/g/n
√
√
Atheros AR2425 802.11b/g
√
√
Intel Wi-Fi Link 5100 802.11a/b/g/n
WLAN module
4
√
Chapter 1 Product description
√
Category
Wireless
External media
card
Ports
Docking
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
Intel Wi-Fi Link 5100 802.11a/b/g
WLAN module
√
Broadcom 4322 802.11a/b/g/n
WLAN module
√
Broadcom BCM4312 802.11b/g
WLAN module
√
Integrated ATSC/NTSC/QAM hybrid
TV tuner module
√
√
√
Integrated world-wide analog DVB-T
TV tuner module
√
√
√
Support for TV tuner antennae for both
DVB-T and ATSC/NTSC
√
√
√
One ExpressCard 54 slot
√
√
Digital Media Slot, supports SD, MMC,
SD I/O, MS, MSP, xD
√
√
√
Audio-in (mono microphone)
√
√
√
Audio-out (stereo headphone)
√
√
√
Audio-out (stereo headphone with S/
PDIF)
√
√
√
Consumer infrared
√
√
√
eSATA
√
√
√
High-Definition Multimedia Interface
(HDMI) v1.3 supporting 1080p with
HDCP key
√
√
√
IEEE 1394a
√
RJ-11 (modem; select models only)
√
√
√
RJ-45 (Ethernet, includes link and
activity lights)
√
√
√
TV tuner antenna (select models only)
√
USB (4 on computer models not
equipped with an eSATA port; 3 on
computer models equipped with an
eSATA port)
√
√
√
VGA (Dsub 15-pin)
√
√
√
2-pin AC power for 90-W AC adapter
√
√
√
Expansion port 3 supports the HP
xb3000 Notebook Expansion Base and
HP Notebook QuickDock
√
√
√
√
√
5
Category
Description
Computer
models equipped
with AMD
processors and
graphics
subsystems with
discrete memory
Computer
models equipped
with AMD
processors and
graphics
subsystems with
UMA memory
Computer models
equipped with
Intel processors
and graphics
subsystems with
discrete memory
Keyboard/
pointing devices
17-inch full-size keyboard with
numeric keypad
√
√
√
Touchpad supports 2-way scrolling
√
√
√
Taps enabled as default
√
√
√
8-cell 2.55-Ah Li-ion battery
√
Power
requirements
6-cell 2.20-Ah Li-ion battery
90-W AC adapter with localized cable
plug support (2-wire plug with ground
pin, supports 2-pin DC connector)
√
√
65-W AC adapter with localized cable
plug support (2-wire plug with ground
pin, supports 2-pin DC connector)
Security
Operating
system
√
√
√
Security cable slot
√
√
√
Fingerprint reader (select models only)
√
√
√
FreeDOS
√
√
√
Linux Red Flag
√
√
√
Windows Vista® Business (32 bit)
√
√
√
Preinstalled:
Windows Vista Home Basic (32 bit) vvv
Serviceability
6
√
Windows Vista Premium (32 bit)
√
√
√
Windows Vista Ultimate (64 bit)
√
√
√
AC adapter
√
√
√
Battery (system)
√
√
√
Hard drives (2)
√
√
√
Memory module
√
√
√
Optical drive
√
√
√
TV tuner module
√
√
√
WLAN module
√
√
√
Chapter 1 Product description
2
External component identification
Top components
Display and top components
Item
Component
Description
(1)
Internal display switch
Turns off the display and initiates Sleep if the display is
closed while the power is on.
(2)
Wireless antennae (select models only)
Send and receive signals from one or more wireless
devices. These antennae are not visible from the
outside of the computer.
NOTE: For optimal transmission, keep the areas
immediately around the antennae free from
obstructions.
NOTE: To see wireless regulatory notices, refer to the
section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These
notices are located in Help and Support.
Top components
7
8
Item
Component
Description
(3)
Internal microphones (2)
Record sound.
(4)
Integrated webcam light
On: The integrated webcam is in use.
(5)
Integrated webcam
Records video and captures still photographs.
Chapter 2 External component identification
Buttons, fingerprint reader, and speakers
Item
Component
Description
(1)
Speakers (2)
Produce sound.
(2)
Power button*
●
When the computer is off, press the button to turn
on the computer.
●
When the computer is on, press the button briefly
to initiate Sleep.
●
When the computer is in the Sleep state, press the
button briefly to exit Sleep.
●
When the computer is in Hibernation, press the
button briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold
the power button for at least 5 seconds to turn off the
computer.
To learn more about your power settings, select Start >
Control Panel > System and Maintenance > Power
Options.
(3)
Media button
●
Launches the QuickPlay program (for models with
QuickPlay preinstalled).
NOTE: If the computer has been set up to require a
logon password, you may be asked to log on to
Windows. QuickPlay launches after you log on. Refer to
the QuickPlay software Help for more information.
(4)
Volume mute button
Mutes and restores speaker sound.
Top components
9
Item
Component
Description
(5)
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to
decrease volume and to the right to increase volume.
You can also tap the minus sign on the scroll zone to
decrease volume, or tap the plus sign on the scroll zone
to increase volume.
(6)
Previous/rewind button
●
Plays the previous track or chapter when the
button is pressed once.
●
Rewinds media when the button is pressed
simultaneously with the fn key.
(7)
Play/pause button
Plays or pauses the disc.
(8)
Next/fast forward button
●
Plays the next track or chapter when the button is
pressed once.
●
Fast forwards media when pressed
simultaneously with the fn key.
(9)
Stop button
Stops playback.
(10)
Wireless button
Turns the wireless feature on or off, but does not create
a wireless connection.
NOTE: A wireless network must be set up in order to
establish a wireless connection.
(11)
Fingerprint reader
Allows a fingerprint logon to Windows, instead of a
password logon.
*This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help
and Support.
10
Chapter 2 External component identification
Keys
Item
Component
Function
(1)
esc key
Displays system information about your computer when
pressed in combination with the fn key.
(2)
fn key
Executes frequently used system functions when
pressed in combination with a function key or the esc
key.
(3)
Windows logo key
Displays the Windows® Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Embedded numeric keypad keys
Can be used like the keys on an external numeric
keypad.
(6)
Function keys
Execute frequently used system functions when
pressed in combination with the fn key.
Top components
11
TouchPad
Item
Component
Function
(1)
TouchPad light
●
White: TouchPad is enabled.
●
Amber: TouchPad is disabled.
(2)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(3)
TouchPad left button*
Functions like the left button on an external mouse.
(4)
TouchPad on/off button
Enables/disables the TouchPad.
(5)
TouchPad scroll zone
Scrolls up or down.
(6)
TouchPad right button*
Functions like the right button on an external mouse.
*This table describes factory settings. View or change pointing device preferences by selecting Start > Control Panel >
Hardware and Sound > Mouse.
12
Chapter 2 External component identification
Front components
Item
Component
Function
(1)
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power
source has reached a low battery level. When the
battery reaches a critical battery level, the battery
light begins blinking rapidly.
●
Off: If the computer is plugged into an external
power source, the light is turned off when all
batteries in the computer are fully charged. If the
computer is not plugged into an external power
source, the light stays off until the battery reaches
a low battery level.
(2)
Battery light
(3)
Drive light
Blinking: The hard drive or optical drive is being
accessed.
(4)
Consumer infrared lens
Receives a signal from the HP Remote Control.
(5)
Audio-in (microphone) jack
Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
(6)
Audio-out (headphone) jacks (2)
Produce sound when connected to optional powered
stereo speakers, headphones, ear buds, a headset, or
television audio.
NOTE: This table describes factory settings. For information about changing factory settings, refer to the user guides located
in Help and Support.
Front components
13
Rear components
Component
Function
Vents (2)
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
It is normal for the internal fan to cycle on and off during routine operation.
Right-side components
Item
Component
Function
(1)
Optical drive light
Blinking: The optical drive is being accessed.
(2)
Optical drive
Reads optical discs and, on select models, also writes
to optical discs.
(3)
USB ports (2)
Connect optional USB devices.
(4)
TV antenna jack (select models only)
Connects a TV antenna, a digital cable device, or a
satellite device that receives standard or high-definition
TV broadcasts.
(5)
RJ-11 (modem) jack (select models only)
Connects a modem cable.
(6)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from
being mishandled or stolen.
(7)
14
Power connector
Chapter 2 External component identification
Connects an AC adapter.
Left-side components
Item
Component
Function
(1)
External monitor port
Connects an external VGA monitor or projector.
(2)
Expansion port 3
Connects the computer to an optional docking device or an
optional expansion product.
NOTE: The computer has only one expansion port. The
term expansion port 3 describes the type of expansion port.
(3)
RJ-45 (network) jack
Connects a network cable.
(4)
HDMI port
Connects an optional video or audio device, such as a highdefinition television, or any compatible digital or audio
component.
(5)
eSATA/USB port
Connects an optional high-performance eSATA
component, such as an eSATA external hard drive, or an
optional USB device.
(6)
USB port
Connects an optional USB device.
(7)
1394 port (select models only)
Connects an optional IEEE 1394 or 1394a device, such as
a camcorder.
(8)
Digital Media Slot light
On: A digital card is being accessed.
(9)
Digital Media Slot
Supports the following optional digital card formats: Secure
Digital (SD) Memory Card, MultiMediaCard (MMC),
Memory Stick (MS), Memory Stick Pro (MSP), xD-Picture
Card (XD), xD-Picture Card (XD) Type H, xD-Picture Card
(XD) Type M.
(10)
ExpressCard slot
Supports optional ExpressCard/54 cards.
Left-side components
15
Bottom components
Item
Component
Function
(1)
Vents (8)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to
cool internal components and prevent overheating. It is
normal for the internal fan to cycle on and off during
routine operation.
(2)
Battery bay
Holds the battery.
(3)
Battery release latch
Releases the battery from the battery bay.
(4)
Memory module compartment
Contains the memory module slots.
(5)
Mini Card module compartment
Holds the TV tuner card and, for select models only, the
Intel Turbo Memory card.
(6)
Hard drive bay and WLAN module
Holds the hard drive and the WLAN module.
CAUTION: To prevent an unresponsive system,
replace the wireless module only with a wireless module
authorized for use in the computer by the governmental
agency that regulates wireless devices in your country
or region. If you replace the module and then receive a
warning message, remove the module to restore
computer functionality, and then contact technical
support through Help and Support.
16
Chapter 2 External component identification
3
Illustrated parts catalog
Service tag
The service tag, affixed to the bottom of the computer, provides information that may be needed when
troubleshooting system problems. The service tag provides the following information:
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the number needed to locate documents, drivers, and support for the
computer.
(5) Warranty period: Describes the duration of the warranty period for the computer.
Service tag
17
Computer major components
18
Item
Description
(1)
15.4-inch display assemblies (include wireless antenna transceivers and cables)
Spare part number
WSXGA+ AntiGlare display assembly with webcam and 2 microphones
484372-001
WSXGA+ BrightView display assembly with webcam and 2 microphones
484368-001
WXGA AntiGlare display assembly with webcam and 2 microphones
484371-001
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
WXGA Brightview display assembly with webcam and 2 microphones
484367-001
NOTE: See Display assembly components on page 27 for more information on display assembly spare part
numbers.
(2)
Switch cover (includes LED board and cable)
488316-001
(3)
Power button board (includes cable)
486796-001
(4)
Keyboards (include keyboard cable)
Belgium
488590-A41
Brazil
488590-201
Canada
488590-121
The Czech Republic
488590-221
Denmark, Norway, and Sweden
488590-DH1
France
488590-051
Germany
488590-041
Greece
488590-151
Hungary
488590-211
Israel
488590-BB1
Italy
488590-061
Japan
488590-291
Latin America
488590-161
The Netherlands and Europe
488590-B31
Portugal
488590-131
Russia
488590-251
Saudi Arabia
488590-171
South Korea
488590-AD1
Spain
488590-071
Switzerland
488590-111
Taiwan
488590-AB1
Thailand
488590-281
Turkey
488590-141
The United Kingdom
488590-031
The United States
488590-001
(5)
Speaker assembly
486801-001
(6)
Bluetooth® modules (do not include a Bluetooth module cable)
For use only with computer models equipped with AMD processors
412766-002
For use only with computer models equipped with Intel processors
483113-001
Computer major components
19
Item
Description
Spare part number
(7)
Bluetooth module cable
489822-001
Cable Kit, includes:
501891-001
NOTE:
See Cable Kit on page 31 for more Cable Kit spare part information.
(8a)
Power connector cable
(8b)
Modem module cable
(8c)
TV tuner module antenna cable
Plastics Kit, includes:
NOTE:
See Plastics Kit on page 30 for more Cable Kit spare part information.
(9a)
ExpressCard slot bezel
(9b)
Mini Card module compartment cover
(9c)
Memory module compartment cover
(9d)
Hard drive bay cover
(10)
Top covers (include TouchPad and TouchPad buttons):
(11)
486793-001
For use only with computer models equipped with a fingerprint reader
486527-001
For use only with computer models not equipped with a fingerprint reader
486526-001
Modem modules:
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is
included in the Cable Kit, spare part number 501891-001.
(12)
For use in all countries and regions except Australia and New Zealand
461749-001
For use only in Australia and New Zealand
461749-011
System boards (include replacement thermal material):
For use only with computer models equipped with AMD processors:
●
With RX781 Northbridge and ATI-M82-S discrete graphics subsystem memory
482324-001
●
With RS780 Northbridge and ATI-M UMA graphics subsystem memory
482325-001
For use only with computer models equipped with Intel processors:
●
With PM45 Northbridge and nVidia NB9P-GS discrete graphics subsystem
memory and 512-GB of graphics subsystem memory
482870-001
●
With PM45 Northbridge and nVidia NB9M-GE discrete graphics subsystem
memory and 256-GB of graphics subsystem memory
482867-001
●
With GM45 Northbridge and UMA graphics subsystem memory
482869-001
●
With ICH9M Northbridge and UMA graphics subsystem memory
482868-001
(13)
Audio/infrared board (includes cable)
486797-001
(14)
USB board (includes cable)
486798-001
(15)
Processors (include replacement thermal material):
AMD processors:
20
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
●
Turion Ultra Dual-Core 35W ZM-86 2.40-GHz processor with 2-MB L2 cache
484260-001
●
Turion Ultra Dual-Core 35W ZM-82 2.20-GHz, processor with 2-MB L2 cache
484261-001
●
Turion Ultra Dual-Core 35W ZM-80 2.10-GHz, processor with 2-MB L2 cache
484262-001
●
Turion Dual-Core 35W RM-70 2.00-GHz with 1-MB L2 cache
484263-001
●
Athlon X2 Dual-Core 35W QL-60 1.90-GHz with 1-MB L2 cache
484264-001
Intel processors:
(16)
(17)
●
Intel Core2 Duo T9600 2.80-GHz processor with 6-MB L2 cache and 1066-MHz
FSB
483859-001
●
Intel Core2 Duo T9400 2.53-GHz processor with 6-MB L2 cache and 1066-MHz
FSB
483860-001
●
Intel Core Duo T8600 2.40-GHz processor with 3-MB L2 cache and 1066-MHz
FSB
483861-001
●
Intel Core Duo T8400 2.26-GHz processor with 3-MB L2 cache and 1066-MHz
FSB
486523-001
Fan/heat sink assemblies (include replacement thermal material):
For use only with computer models equipped with AMD processors and graphics
subsystems with discrete memory
493001-001
For use only with computer models equipped with AMD processors and graphics
subsystems with UMA memory
491572-001
For use only with computer models equipped with Intel processors and graphics
subsystems with discrete memory
486799-001
For use only with computer models equipped with Intel processors and graphics
subsystems with UMA memory
492314-001
Base enclosures (include rubber feet)
For use only with computer models equipped with a 1394 port, modem module, and
TV tuner module
486783-001
For use only with computer models equipped with a 1394 port and modem module, but
not a TV tuner module
486784-001
For use only with computer models equipped with a 1394 port and TV tuner module,
but not a modem module
486785-001
For use only with computer models equipped with a 1394 port, but not a modem module 486786-001
or a TV tuner module
For use only with computer models equipped with a modem module and a TV tuner
module, but not a 1394 port
486787-001
For use only with computer models equipped with a TV tuner module, but not a 1394
port or modem module
486788-001
For use only with computer models equipped with a modem module, but not a 1394
port or TV tuner module
486789-001
For use only with computer models not equipped with a 1394 port, modem module, or 486790-001
TV tuner module
Rubber Feet Kit (not illustrated, includes 4 base enclosure rubber feet)
486794-001
Computer major components
21
Item
Description
(18)
Batteries:
(19)
Spare part number
12-cell, 95-Wh, 2.55-Ah Li-ion battery for use with all computer models
484172-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery for use with all computer models
484171-001
6-cell, 47-Wh, 2.55-Ah Li-ion battery for use only with computer models equipped with
AMD processors
484170-002
6-cell, 47-Wh, 2.55-Ah Li-ion battery for use only with computer models equipped with
Intel processors
484170-001
Optical drives (include bezel and bracket):
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and
bronze bezel
486525-002
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and
silver bezel
486525-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
bronze bezel for use only with computer models equipped with AMD processors
483864-003
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
bronze bezel for use only with computer models equipped with Intel processors
483864-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
silver bezel
483864-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with bronze bezel
483863-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with silver bezel
483863-001
(20)
RTC battery
491571-001
(21)
TV tuner modules:
NOTE: The TV tuner module spare part kits do not include a TV tuner module cable. The TV tuner module cable
is included in the Cable Kit, spare part number 501891-001.
DVB-T TV tuner module
482899-003
DVB-T/ANG TV tuner module
482899-002
NTSC/ATSC/ANG TV tuner module
482899-001
TV tuner external antenna cables (not illustrated):
(22)
22
With F-PAL jack
482900-001
With PAL jack
482900-002
Memory modules (667-MHz, PC2-5300, 1-DIMM):
2048-MB memory module for use only with computer models equipped with AMD
processors
484268-002
1024-MB memory module for use only with computer models equipped with AMD
processors
484267-002
2048-MB memory module for use only with computer models equipped with Intel
processors
484268-001
1024-MB memory module for use only with computer models equipped with Intel
processors
484267-001
Chapter 3 Illustrated parts catalog
Item
(23)
Description
Spare part number
512-MB memory module for use only with computer models equipped with Intel
processors
484266-001
WLAN modules:
WLAN modules for use only with computer models equipped with AMD processors:
●
Atheros AR9280 802.11a/b/g/n WLAN module for use in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
482260-001
●
Atheros AR9280 802.11a/b/g/n WLAN module for use in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
482260-002
●
Broadcom 4321 802.11a/b/g/n WLAN module for use in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
453730-001
●
Broadcom 4321 802.11a/b/g/n WLAN module for use in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
453730-002
Computer major components
23
Item
Description
Spare part number
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
●
Atheros AR2425 802.11b/g for use in Antigua and Barbuda, Barbados, Belize,
Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
459339-001
●
Atheros AR2425 802.11b/g for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria,
Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia,
the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga,
Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459339-002
WLAN modules for use only with computer models equipped with Intel processors:
24
●
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use in all countries and
regions
482957-001
●
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and
regions
480985-001
●
Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
487330-001
●
Broadcom 4322 802.11a/b/g/n WLAN module for use in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
487330-002
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
(24)
●
Broadcom BCM4312 802.11b/g WLAN module for use in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459263-001
●
Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
459263-002
Hard drives (include left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators):
Computer major components
25
Item
Description
Spare part number
Hard drives for use only with computer models equipped with AMD processors:
●
320-GB, 5400-rpm
462355-002
●
250-GB, 5400-rpm
489819-002
●
160-GB, 5400-rpm
489818-002
●
120-GB, 5400-rpm
489817-002
Hard drives for use only with computer models equipped with Intel processors:
●
320-GB, 5400-rpm
462355-001 and
489821-001
●
250-GB, 5400-rpm
489819-001
●
160-GB, 7200-rpm
489820-001
●
160-GB, 5400-rpm
489818-001
●
120-GB, 5400-rpm
489817-001
Hard Drive Hardware Kit (not illustrated, includes left and right bracket rails, connector
cable, Mylar cover with tab, and 4 rubber isolators)
26
Chapter 3 Illustrated parts catalog
483862-001
Display assembly components
The HP Pavilion dv5 Entertainment PC offers 2 types of display assemblies. Component spare parts
are listed in this section for AntiGlare display assemblies and BrightView display assemblies.
AntiGlare display assembly spare parts
Item
Description
Spare part number
(1)
Display enclosure (includes wireless antenna transceivers and cables):
485339-001
(2)
Display inverter cover
486792-001
(3)
Display inverter
488317-001
(4)
Webcam/microphone module
485345-001
(5)
Display Hinge Kit (includes left and right hinges)
485340-001
Display Rubber Kit (not illustrated, includes display bezel rubber screw covers)
486537-001
Display Screw Kit (not illustrated)
485343-001
Display assembly components
27
BrightView display assembly spare parts
28
Item
Description
Spare part number
(1)
Display bezel (includes logo and display lid switch actuator magnet)
480444-001
(2)
Webcam/microphone module
480446-001
(3)
BrightView display panels (include display panel cable):
For use only with computer models equipped with WSXGA+ display panels
480441-001
For use only with computer models equipped with WXGA display panels
480440-001
(4)
Display Hinge Kit (includes left and right hinges)
486534-001
(5)
Display Cable Kits (include display panel cable, not illustrated, and microphone receiver and cable)
For use only with computer models equipped with WSXGA+ display panels
486536-001
For use only with computer models equipped with WXGA display panels
493020-001
Chapter 3 Illustrated parts catalog
Item
Description
(6)
Wireless antenna transceivers and cables:
Spare part number
For use with computer models equipped with 802.11a/b/g/n WLAN modules (includes
3 wireless antenna transceivers and cables)
489804-001
For use with computer models equipped with 802.11a/b/g and 802.11b/g WLAN
modules (includes 2 wireless antenna transceivers and cables)
487748-001
(7)
Display inverter
488317-001
(8)
Display enclosures (include wireless antenna transceivers and cables and logo LED board and cable):
For use with computer models equipped with 802.11a/b/g/n WLAN modules (includes
3 wireless antenna transceivers and cables)
480445-001
For use with computer models equipped with 802.11a/b/g and 802.11b/g WLAN
modules (includes 2 wireless antenna transceivers and cables)
488884-001
Display Rubber Kit (not illustrated, includes display bezel rubber screw covers)
480442-001
Display Screw Kit (not illustrated)
480443-001
Display assembly components
29
Plastics Kit
Item
30
Description
Spare part number
Plastics Kit
486793-001
(1)
ExpressCard slot bezel
(2)
Mini Card module compartment cover (includes 1 captive screw, secured by a C-clip)
(3)
Memory module compartment cover (includes 1 captive screw, secured by a C-clip)
(4)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
Chapter 3 Illustrated parts catalog
Cable Kit
Item
Description
Spare part number
Cable Kit
501891-001
(1)
Bluetooth module cable
(2)
Power connector cable
(3)
Modem module cable (includes RJ-11 jack)
(4)
TV tuner module cable
Cable Kit
31
Mass storage devices
Item
Description
Spare part number
(1)
Hard drives (include left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators):
For use only with computer models equipped with AMD processors:
●
320-GB, 5400-rpm
462355-002
●
250-GB, 5400-rpm
489819-002
●
160-GB, 5400-rpm
489818-002
●
120-GB, 5400-rpm
489817-002
For use only with computer models equipped with Intel processors:
●
320-GB, 5400-rpm
462355-001 and
489821-001
●
250-GB, 5400-rpm
489819-001
●
160-GB, 7200-rpm
489820-001
●
160-GB, 5400-rpm
489818-001
●
120-GB, 5400-rpm
489817-001
Hard Drive Hardware Kit (not illustrated, includes left and right bracket rails,
connector cable, Mylar cover with tab, and 4 rubber isolators)
(2)
Optical drives (include bezel and bracket)
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and
bronze bezel
32
483862-001
Chapter 3 Illustrated parts catalog
486525-002
Item
Description
Spare part number
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and
silver bezel
486525-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
bronze bezel for use only with computer models equipped with AMD processors
483864-003
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
bronze bezel for use only with computer models equipped with Intel processors
483864-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and
silver bezel
483864-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with bronze bezel
483863-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with silver bezel
483863-001
Mass storage devices
33
Miscellaneous parts
Description
Spare part number
AC adapters
90-W AC adapter
391173-001 and
463955-001
65-W AC adapter
463958-001
Carrying cases
HP carrying case
418162-001
HP slim bag
418163-001
CAT5E cable
454619-001
Wired headset with volume control
371693-003
Optical mouse
436238-001
Wireless laser mouse (includes infrared transceiver)
430958-001
Power cords:
Argentina
490371-D01
Australia and New Zealand
490371-011
Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain,
and Sweden
490371-021
Brazil
490371-201
Canada, French Canada, Latin America, Thailand, and the United States
490371-001
Denmark
490371-081
India
490371-D61
Israel
490371-BB1
Italy
490371-061
Japan
490371-291
The People's Republic of China
490371-AA1
South Africa
490371-AR1
South Korea
490371-AD1
Switzerland
490371-111
Taiwan
490371-AB1
The United Kingdom and Hong Kong
490371-031
Remote controls
34
Full-function remote control
465540-001
Full-function remote control with teletext
464793-001
Chapter 3 Illustrated parts catalog
Description
Spare part number
Thin profile remote control (fits into ExpressCard slot)
465541-001
Screw Kit
486795-001 and
493002-001
●
Phillips PM3.0×4.0 screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×6.0 screw
●
Phillips PM2.5×6.0 captive screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.0×10.0 captive screw
●
Phillips PM2.0×4.0 screw
Sequential part number listing
Spare part
number
Description
371693-003
Wired headset with volume control
391173-001
90-W AC adapter
412766-002
Bluetooth module for use only with computer models equipped with AMD processors (does not include a
Bluetooth module cable)
NOTE:
The Bluetooth module cable is available using spare part number 489822-001.
418162-001
HP carrying case
418163-001
HP slim bag carrying case
430958-001
Wireless laser mouse (includes infrared transceiver)
436238-001
Optical mouse
453730-001
Broadcom 4321 802.11a/b/g/n WLAN module for use only with computer models equipped with AMD
processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
453730-002
Broadcom 4321 802.11a/b/g/n WLAN module for use only with computer models equipped with AMD
processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia,
Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Sequential part number listing
35
Spare part
number
Description
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
36
454619-001
CAT5E cable
459263-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computer models equipped with Intel
processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459263-002
Broadcom BCM4312 802.11b/g WLAN module for use only with computer models equipped with Intel
processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia,
Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459339-001
Atheros AR2425 802.11b/g for use only with computer models equipped with AMD processors in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459339-002
Atheros AR2425 802.11b/g for use only with computer models equipped with AMD processors in
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize,
Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands,
Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Chapter 3 Illustrated parts catalog
Spare part
number
Description
461749-001
Modem module for use in all countries and regions except Australia and New Zealand
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 501891-001.
461749-011
Modem module for use only in Australia and New Zealand
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 501891-001.
462355-001
320-GB, 5400-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
462355-002
320-GB, 5400-rpm hard drive for use only with computer models equipped with AMD processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
463955-001
90-W AC adapter
463958-001
65-W AC adapter
464793-001
Full-function remote control with teletext
465540-001
Full-function remote control
465541-001
Thin profile remote control (fits into ExpressCard slot)
480985-001
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use only with computer models equipped with Intel
processors in all countries and regions
482260-001
Atheros AR9280 802.11a/b/g/n WLAN module for use only with computer models equipped with AMD
processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
482260-002
Atheros AR9280 802.11a/b/g/n WLAN module for use only with computer models equipped with AMD
processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia,
Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
482324-001
System board with RX781 Northbridge and ATI-M82-S discrete graphics subsystem memory for use only
with computer models equipped with AMD processors (includes replacement thermal material)
482325-001
System board with RS780 Northbridge and ATI-M UMA graphics subsystem memory for use only with
computer models equipped with AMD processors (includes replacement thermal material)
Sequential part number listing
37
Spare part
number
Description
482867-001
System board with PM45 Northbridge and nVidia NB9M-GE discrete graphics subsystem memory for use
only with computer models equipped with Intel processors (includes replacement thermal material)
482868-001
System board with ICH9M Northbridge and UMA graphics subsystem memory for use only with computer
models equipped with Intel processors (includes replacement thermal material)
482869-001
System board with GM45 Northbridge and UMA graphics subsystem memory for use only with computer
models equipped with Intel processors (includes replacement thermal material)
482870-001
System board with PM45 Northbridge and nVidia NB9P-GS discrete graphics subsystem memory for use
only with computer models equipped with Intel processors (includes replacement thermal material)
482899-001
NTSC/ATSC/ANG TV tuner module
NOTE: The TV tuner module spare part kits do not include a TV tuner module cable. The TV tuner
module cable is included in the Cable Kit, spare part number 501891-001.
482899-002
DVB-T/ANG TV tuner module
NOTE: The TV tuner module spare part kits do not include a TV tuner module cable. The TV tuner
module cable is included in the Cable Kit, spare part number 501891-001.
482899-003
DVB-T TV tuner module
NOTE: The TV tuner module spare part kits do not include a TV tuner module cable. The TV tuner
module cable is included in the Cable Kit, spare part number 501891-001.
482900-001
TV tuner external antenna cable with F-PAL jack
482900-002
TV tuner external antenna cable with PAL jack
482957-001
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use only with computer models equipped with Intel
processors in all countries and regions
483113-001
Bluetooth module for use only with computer models equipped with Intel processors (does not include a
Bluetooth module cable)
NOTE: The Bluetooth module cable is available using spare part number 489822-001.
38
483859-001
Intel Core2 Duo T9600 2.80-GHz processor with 6-MB L2 cache and 1066-MHz FSB (includes
replacement thermal material)
483860-001
Intel Core2 Duo T9400 2.53-GHz processor with 6-MB L2 cache and 1066-MHz FSB (includes
replacement thermal material)
483861-001
Intel Core Duo T8600 2.40-GHz processor with 3-MB L2 cache and 1066-MHz FSB (includes replacement
thermal material)
483862-001
Hard Drive Hardware Kit (includes left and right bracket rails, connector cable, Mylar cover with tab, and
4 rubber isolators)
483863-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with bronze bezel (includes bezel and
bracket)
483863-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with bronze bezel (includes bezel and
bracket)
483864-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and silver bezel (includes
bezel and bracket)
483864-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and bronze bezel for use
only with computer models equipped with Intel processors (includes bezel and bracket)
483864-003
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe and bronze bezel for use
only with computer models equipped with AMD processors (includes bezel and bracket)
Chapter 3 Illustrated parts catalog
Spare part
number
Description
484170-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery for use with all computer models
484170-002
6-cell, 47-Wh, 2.55-Ah Li-ion battery for use only with computer models equipped with AMD processors
484171-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery for use with all computer models
484172-001
12-cell, 95-Wh, 2.55-Ah Li-ion battery for use with all computer models
484260-001
AMD Turion Ultra Dual-Core 35W ZM-86 2.40-GHz processor with 2-MB L2 cache (includes replacement
thermal material)
484261-001
AMD Turion Ultra Dual-Core 35W ZM-82 2.20-GHz, processor with 2-MB L2 cache (includes replacement
thermal material)
484262-001
AMD Turion Ultra Dual-Core 35W ZM-80 2.10-GHz, processor with 2-MB L2 cache (includes replacement
thermal material)
484263-001
AMD Turion Dual-Core 35W RM-70 2.00-GHz with 1-MB L2 cache processor (includes replacement
thermal material)
484264-001
AMD Athlon X2 Dual-Core 35W QL-60 1.90-GHz with 1-MB L2 cache processor (includes replacement
thermal material)
484266-001
512-MB memory module for use only with computer models equipped with Intel processors (667-MHz,
PC2-5300, 1-DIMM)
484267-001
1024-MB memory module for use only with computer models equipped with Intel processors (667-MHz,
PC2-5300, 1-DIMM)
484267-002
1024-MB memory module for use only with computer models equipped with AMD processors (667-MHz,
PC2-5300, 1-DIMM)
484268-001
2048-MB memory module for use only with computer models equipped with Intel processors (667-MHz,
PC2-5300, 1-DIMM)
484268-002
2048-MB memory module for use only with computer models equipped with AMD processors (667-MHz,
PC2-5300, 1-DIMM)
484363-001
15.4-inch WXGA BrightView display panel (includes display panel cable)
484364-001
15.4-inch WSXGA+ BrightView display panel (includes display panel cable)
484367-001
15.4-inch WXGA Brightview display assembly with webcam and 2 microphones
484368-001
15.4-inch WSXGA+ BrightView display assembly with webcam and 2 microphones
484371-001
15.4-inch WXGA AntiGlare display assembly with webcam and 2 microphones
484372-001
15.4-inch WSXGA+ AntiGlare display assembly with webcam and 2 microphones
485339-001
Display enclosure for use only with computer models equipped with AntiGlare display assemblies
(includes wireless antenna transceivers and cables)
485340-001
Display Hinge Kit for use only with computer models equipped with AntiGlare display assemblies (includes
left and right hinges)
485343-001
Display Screw Kit
485344-001
Display Hinge Screw Kit
485345-001
Webcam/microphone module for use only with computer models equipped with AntiGlare display
assemblies (includes double-sided tape)
486523-001
Intel Core Duo T8400 2.26-GHz processor with 3-MB L2 cache and 1066-MHz FSB (includes replacement
thermal material)
Sequential part number listing
39
Spare part
number
Description
486525-001
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and bronze bezel
(includes bezel and bracket)
486525-002
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer, LightScribe, and bronze bezel
(includes bezel and bracket)
486526-001
Top cover for use only with computer models not equipped with a fingerprint reader (includes TouchPad
and TouchPad buttons)
486527-001
Top cover for use only with computer models equipped with a fingerprint reader (includes TouchPad and
TouchPad buttons)
486532-001
Display bezel
486533-001
Display enclosure (includes logo)
486534-001
Display Hinge Kit for use only with computer models equipped with BrightView display assemblies
(includes left and right display hinges)
486536-001
Display panel cable for use with WSXGA+ BrightView display panels
486537-001
Display Rubber Kit (includes display bezel rubber screw covers)
486783-001
Base enclosure for use only with computer models equipped with a 1394 port, modem module, and TV
tuner module (includes rubber feet)
486784-001
Base enclosure for use only with computer models equipped with a 1394 port and modem module, but
not a TV tuner module (includes rubber feet)
486785-001
Base enclosure for use only with computer models equipped with a 1394 port and TV tuner module, but
not a modem module (includes rubber feet)
486786-001
Base enclosure for use only with computer models equipped with a 1394 port, but not a modem module
or a TV tuner module (includes rubber feet)
486787-001
Base enclosure for use only with computer models equipped with a modem module and a TV tuner module,
but not a 1394 port (includes rubber feet)
486788-001
Base enclosure for use only with computer models equipped with a TV tuner module, but not a 1394 port
or modem module (includes rubber feet)
486789-001
Base enclosure for use only with computer models equipped with a modem module, but not a 1394 port
or TV tuner module (includes rubber feet)
486790-001
Base enclosure for use only with computer models not equipped with a 1394 port, modem module, or TV
tuner module (includes rubber feet)
486791-001
Webcam/microphone module for use only with computer models equipped with BrightView display
assemblies (includes double-sided tape)
486792-001
Display inverter cover (for use only with computer models equipped with BrightView display
assemblies)
486793-001
Plastics Kit
NOTE: See Plastics Kit on page 30 for more Cable Kit spare part information.
40
486794-001
Rubber Feet Kit (includes 4 base enclosure rubber feet)
486795-001
Screw Kit
486796-001
Power button board (includes cable)
486797-001
Audio/infrared board (includes cable)
Chapter 3 Illustrated parts catalog
Spare part
number
Description
486798-001
USB board (includes cable)
486799-001
Fan/heat sink assembly for use only with computer models equipped with Intel processors and graphics
subsystems with discrete memory (includes replacement thermal material)
486801-001
Speaker assembly
487330-001
Broadcom 4322 802.11a/b/g/n WLAN module for use only with computer models equipped with Intel
processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
487330-002
Broadcom 4322 802.11a/b/g/n WLAN module for use only with computer models equipped with Intel
processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia,
Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
488316-001
Switch cover (includes LED board and cable)
488317-001
Display inverter
488590-001
Keyboard for use in the United States
488590-031
Keyboard for use in the United Kingdom
488590-041
Keyboard for use in Germany
488590-051
Keyboard for use in France
488590-061
Keyboard for use in Italy
488590-071
Keyboard for use in Spain
488590-111
Keyboard for use in Switzerland
488590-121
Keyboard for use in French Canada
488590-131
Keyboard for use in Portugal
488590-141
Keyboard for use in Turkey
488590-151
Keyboard for use in Greece
488590-161
Keyboard for use in Latin America
488590-171
Keyboard for use in Saudi Arabia
Sequential part number listing
41
42
Spare part
number
Description
488590-201
Keyboard for use in Brazil
488590-211
Keyboard for use in Hungary
488590-221
Keyboard for use in the Czech Republic
488590-251
Keyboard for use in Russia
488590-281
Keyboard for use in Thailand
488590-291
Keyboard for use in Japan
488590-A41
Keyboard for use in Belgium
488590-AB1
Keyboard for use in Taiwan
488590-AD1
Keyboard for use in South Korea
488590-B31
Keyboard for use in the Netherlands
488590-BB1
Keyboard for use in Israel
488590-DH1
Keyboard for use in Denmark, Norway, and Sweden
489817-001
120-GB, 5400-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489817-002
120-GB, 5400-rpm hard drive for use only with computer models equipped with AMD processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489818-001
160-GB, 5400-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489818-002
160-GB, 5400-rpm hard drive for use only with computer models equipped with AMD processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489819-001
250-GB, 5400-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489819-002
250-GB, 5400-rpm hard drive for use only with computer models equipped with AMD processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489820-001
160-GB, 7200-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489821-001
320-GB, 5400-rpm hard drive for use only with computer models equipped with Intel processors (includes
left and right bracket rails, connector cable, Mylar cover with tab, and 4 rubber isolators)
489822-001
Bluetooth module cable
490371-001
Power cord for use in Canada, French Canada, Latin America, Thailand, and the United States
490371-011
Power cord for use in Australia and New Zealand
490371-021
Power cord for use in Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway,
Portugal, Spain, and Sweden
490371-031
Power cord for use in the United Kingdom and Hong Kong
490371-061
Power cord for use in Italy
490371-081
Power cord for use in Denmark
490371-111
Power cord for use in Switzerland
490371-201
Power cord for use in Brazil
Chapter 3 Illustrated parts catalog
Spare part
number
Description
490371-291
Power cord for use in Japan
490371-AA1
Power cord for use in the People's Republic of China
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in South Korea
490371-AR1
Power cord for use in South Africa
490371-BB1
Power cord for use in Israel
490371-D01
Power cord for use in Argentina
490371-D61
Power cord for use in India
491571-001
RTC battery
491572-001
Fan/heat sink assembly for use only with computer models equipped with AMD processors and graphics
subsystems with UMA memory (includes replacement thermal material)
492314-001
Fan/heat sink assembly for use only with computer models equipped with Intel processors and graphics
subsystems with UMA memory (includes replacement thermal material)
493001-001
Fan/heat sink assembly for use only with computer models equipped with AMD processors and graphics
subsystems with discrete memory (includes replacement thermal material)
493002-001
Screw Kit
493020-001
Display Cable Kit for use with WXGA BrightView display panels
501891-001
Cable Kit
NOTE:
See Cable Kit on page 31 for more Cable Kit spare part information.
Sequential part number listing
43
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
●
Flat-bladed screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use
care when handling the plastic parts. Apply pressure only at the points designated in the maintenance
instructions.
44
Chapter 4 Removal and replacement procedures
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Preliminary replacement requirements
45
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
46
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Chapter 4 Removal and replacement procedures
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are
selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Preliminary replacement requirements
47
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
48
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Chapter 4 Removal and replacement procedures
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password.
NOTE:
These steps also clear CMOS.
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the RTC battery (see RTC battery on page 59).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
Preliminary replacement requirements
49
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 91 screws, in 8 different sizes, that must be removed, replaced, or loosened when
servicing the computer. Make special note of each screw size and location during removal and
replacement.
Service tag
The service tag, affixed to the bottom of the computer, provides information that may be needed when
troubleshooting system problems. The service tag provides the following information:
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the number needed to locate documents, drivers, and support for the
computer.
(5) Warranty period: Describes the duration of the warranty period for the computer.
50
Chapter 4 Removal and replacement procedures
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare
part number 486794-001. There are 4 rubber feet that attach to the base enclosure in the locations
illustrated below.
Component replacement procedures
51
Battery
Description
Spare part number
12-cell, 95-Wh, 2.55-Ah Li-ion battery for use with all computer models
484172-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery for use with all computer models
484171-001
6-cell, 47-Wh, 2.55-Ah Li-ion battery for use only with computer models equipped with AMD
processors
484170-002
6-cell, 47-Wh, 2.55-Ah Li-ion battery for use only with computer models equipped with Intel
processors
484170-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
3.
Pivot the battery (2) upward and remove it (3) from the computer.
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge of
the battery downward until it is seated. The battery release latch automatically locks the battery into
place.
52
Chapter 4 Removal and replacement procedures
Webcam/microphone module
NOTE: This section applies only to computer models equipped with BrightView display assemblies.
See Display assembly on page 76 for webcam/microphone module removal instructions for computer
models equipped with AntiGlare display assemblies.
NOTE: If it has been determined that the webcam/microphone module is the component that must be
replaced to complete the computer repair, the display assembly does not have to be removed. Follow
the procedures in this section to replace the webcam/microphone module. For information on replacing
the display assembly and other display assembly internal components, see Display assembly
on page 76.
Description
Spare part number
Webcam/microphone module for use only with computer models equipped with BrightView display
assemblies (includes double-sided tape)
486791-001
Before removing the webcam/microphone module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the webcam/microphone module:
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as possible.
3.
Flex the inside edges of the top edge (1) and the left and right upper corners (2) of the display bezel
until the bezel disengages from the display enclosure.
Component replacement procedures
53
4.
Release the display bezel top edge (3) from the display enclosure.
5.
Release the webcam/microphone module (1) from the display enclosure as far as the webcam/
microphone module cable allows.
6.
Disconnect the webcam/microphone module cable (2) from the webcam/microphone module.
7.
Remove the webcam/microphone module.
Reverse this procedure to install the webcam/microphone module.
54
Chapter 4 Removal and replacement procedures
Optical drive
NOTE:
All optical drive spare part kits include an optical drive bezel and bracket.
Description
Spare part number
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer with LightScribe and bronze
bezel
486525-002
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer with LightScribe and silver
bezel
486525-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with bronze bezel
483863-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe with bronze bezel
for use only with computer models equipped with AMD processors
483864-003
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe with bronze bezel
for use only with computer models equipped with Intel processors
483864-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe with silver bezel
483864-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with silver bezel
483863-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the optical drive:
1.
Position the computer with front toward you.
2.
Remove the Phillips PM2.5×7.0 screw (1) that secures the optical drive to the computer.
3.
Insert a thin tool, such as a paper clip (2), into the disc tray release access hole. (The optical drive
disc tray is partially ejected from the optical drive.)
Component replacement procedures
55
4.
Use the disc tray frame to slide the optical drive (3) out of the computer.
5.
Remove the optical drive.
6.
If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
7.
Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical
drive.
8.
Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install the optical drive.
56
Chapter 4 Removal and replacement procedures
TV tuner module
NOTE: The TV tuner module spare part kits do not include a TV tuner module cable. The TV tuner
module cable is included in the Cable Kit, spare part number 501891-001.
NOTE: The TV tuner external antenna cables are available using spare part numbers 482900-001
(with F-PAL jack) and 482900-002 (with PAL jack).
Description
Spare part number
DVB-T TV tuner module
482899-003
DVB-T/ANG TV tuner module
482899-002
NTSC/ATSC/ANG TV tuner module
482899-001
Before removing the TV tuner module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the TV tuner module:
1.
Position the computer with the front toward you
2.
Loosen the Phillips PM2.5×6.0 captive screw (1) that secures the Mini Card module compartment
cover to the computer.
3.
Lift the right side of the Mini Card module compartment cover (2), swing it to left, and remove the
cover (3). The Mini Card module compartment cover is included in the Plastics Kit, spare part
number 486793-001.
4.
Disconnect the TV tuner module antenna cable (1) from the terminal on the TV tuner module.
Component replacement procedures
57
5.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the TV tuner module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
6.
Remove the TV tuner module (3) by pulling the module away from the slot at an angle.
NOTE: The TV tuner module is designed with a notch (4) to prevent incorrect insertion into the
TV tuner module slot.
Reverse this procedure to install the TV tuner module.
58
Chapter 4 Removal and replacement procedures
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery
491571-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the Mini Card module compartment cover (see TV tuner module on page 57).
Remove the RTC battery:
Remove the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery. Be sure that the RTC battery is installed with the “+”
sign facing up.
Component replacement procedures
59
Memory module
Description
Spare part number
For use only with computer models equipped with AMD processors (667-MHz, PC2-5300, 1-DIMM):
2048-MB
484268-002
1024-MB
484267-002
For use only with computer models equipped with Intel processors (667-MHz, PC2-5300, 1-DIMM):
2048-MB
484268-001
1024-MB
484267-001
512-MB
484266-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the memory module:
60
1.
Position the computer with the front toward you.
2.
Loosen the Phillips PM2.5×6.0 captive screw (1) that secures the memory module compartment
cover to the computer.
3.
Lift the left edge of the cover (2), swing it up and to the right, and remove the cover (3). The memory
module compartment cover is included in the Plastics Kit, spare part number 486793-001.
4.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
Chapter 4 Removal and replacement procedures
5.
Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install a memory module.
Component replacement procedures
61
Hard drive
NOTE: All hard drive spare part kits include left and right bracket rails, a connector cable, Mylar cover
with tab, and 4 rubber isolators.
Description
Spare part number
Hard drives for use only with computer models equipped with AMD processors:
320-GB, 5400-rpm
462355-002
250-GB, 5400-rpm
489819-002
160-GB, 5400-rpm
489818-002
120-GB, 5400-rpm
489817-002
Hard drives for use only with computer models equipped with Intel processors:
320-GB, 5400-rpm
462355-001 and
489821-001
250-GB, 5400-rpm
489819-001
160-GB, 7200-rpm
489820-001
160-GB, 5400-rpm
489818-001
120-GB, 5400-rpm
489817-001
Hard Drive Hardware Kit (includes left and right bracket rails, connector cable, Mylar cover with
tab, and 4 rubber isolators)
483862-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the hard drive:
62
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.5×6.0 captive screws (1) that secure the hard drive bay cover to the
computer.
Chapter 4 Removal and replacement procedures
3.
Lift the right side of the hard drive bay cover (2), swing it up and to the left, and remove the
cover (3). The hard drive bay cover is included in the Plastics Kit, spare part number
486793-001.
4.
Use the Mylar tab (1) to slide the hard drive to the left (2), and then lift it to release it from the hard
drive bay.
5.
Disconnect the hard drive cable (3) from the system board.
6.
Remove the hard drive from the hard drive bay.
Component replacement procedures
63
7.
If it is necessary to replace the hard drive bracket or any of the hard drive bracket components,
remove the following:
(1) Four Phillips PM3.0×3.0 screws that secure the hard drive bracket rails and Mylar cover to the
hard drive
(2) Left and right hard drive bracket rails
(3) Mylar cover with tab
(4) Four rubber isolators
(5) Hard drive connector cable
Reverse this procedure to reassemble and install the hard drive.
64
Chapter 4 Removal and replacement procedures
WLAN module
Description
Spare part number
For use only with computer models equipped with AMD processors:
Atheros AR9280 802.11a/b/g/n WLAN module for use only with computer models equipped with
AMD processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
482260-001
Atheros AR9280 802.11a/b/g/n WLAN module for use only with computer models equipped with
AMD processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,
Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
482260-002
Broadcom 4321 802.11a/b/g/n WLAN module for use only with computer models equipped with
AMD processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
453730-001
Broadcom 4321 802.11a/b/g/n WLAN module for use only with computer models equipped with
AMD processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,
Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
453730-002
Component replacement procedures
65
Description
Spare part number
Atheros AR2425 802.11b/g for use only with computer models equipped with AMD processors in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459339-001
Atheros AR2425 802.11b/g for use only with computer models equipped with AMD processors in
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba,
Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia,
the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459339-002
For use only with computer models equipped with Intel processors:
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use only with computer models equipped
with Intel processors in all countries and regions
480985-001
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use only with computer models equipped with
Intel processors in all countries and regions
482957-001
Broadcom 4322 802.11a/b/g/n WLAN module for use only with computer models equipped with 487330-001
Intel processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
Broadcom 4322 802.11a/b/g/n WLAN module for use only with computer models equipped with 487330-002
Intel processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,
Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
66
Chapter 4 Removal and replacement procedures
Description
Spare part number
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom BCM4312 802.11b/g WLAN module for use only with computer models equipped with
Intel processors in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459263-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computer models equipped with
Intel processors in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,
Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459263-002
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the hard drive (see Hard drive on page 62).
Remove the WLAN module:
Component replacement procedures
67
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless devices
in your country or region. If you replace the module and then receive a warning message, remove the
module to restore computer functionality, and then contact technical support through Help and Support.
1.
Disconnect the WLAN antenna cables (1) from the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
2.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
3.
Remove the WLAN module (3) by pulling it away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion into the WLAN
module slot.
Reverse this procedure to install a WLAN module.
68
Chapter 4 Removal and replacement procedures
Switch cover and keyboard
Description
Spare part number
Switch cover (includes LED board and cable)
488316-001
Keyboards
For use in country or region
Spare part number
For use in country or region
Spare part number
Belgium
488590-A41
The Netherlands
488590-
Brazil
488590-201
Portugal
488590-
Canada
488590-121
Russia
488590-
The Czech Republic
488590-221
Saudi Arabia
488590-
Denmark, Norway, and
Sweden
488590-DH1
South Korea
488590-
France
488590-051
Spain
488590-
Germany
488590-041
Switzerland
488590-
Greece
488590-151
Taiwan
488590-
Hungary
488590-211
Thailand
488590-
Israel
488590-BB1
Turkey
488590-
Italy
488590-061
The United Kingdom
488590-
Japan
488590-291
The United States
488590-
Latin America
488590-161
Before removing the switch cover and keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
Remove the switch cover and keyboard:
1.
Position the computer with the front toward you.
Component replacement procedures
69
2.
Remove the following screws:
(1) Two Phillips PM2.5×7.0 screws that secure the keyboard to the computer
(2) Two Phillips PM2.5×7.0 screws that secure the switch cover to the computer
(3) Three Phillips PM2.0×4.0 screws that secure the switch cover to the computer
70
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Lift the rear edge of the switch cover (1) until it detaches from the computer.
6.
Slide the switch cover (2) back until it rests on the display.
Chapter 4 Removal and replacement procedures
7.
Remove the four Phillips PM2.0×4.0 screws that secure the keyboard to the computer.
8.
Lift the rear edge of the keyboard (1) until it rests at an angle.
9.
Slide the keyboard (2) back until the keyboard connector on the system board is accessible.
Component replacement procedures
71
10. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is connected and
disconnect the cable (2) from the system board.
11. Remove the keyboard.
12. Disconnect the power button board cable (1) from the low insertion force (LIF) connector on the
system board.
13. Disconnect the LED board cable (2) from the LIF connector on the system board.
14. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
72
Chapter 4 Removal and replacement procedures
Power button board
Description
Spare part number
Power button board (includes cable)
486796-001
Before removing the power button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 69).
Remove the power button board:
1.
Turn the switch cover upside down with the front toward you.
2.
Remove the Phillips PM2.0×4.0 screw (1) that secures the power button board to the switch cover.
3.
Remove the power button board (2) and cable.
Reverse this procedure to install the power button board.
Component replacement procedures
73
Speaker assembly
Description
Spare part number
Speaker assembly
486801-001
Before removing the speaker assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 69).
Remove the speaker assembly:
1.
Disconnect the speaker assembly cable (1) from the system board.
2.
Remove the speaker assembly cable from the clips (2) in the top cover.
3.
Remove the speaker assembly (3).
Reverse this procedure to install the speaker assembly.
74
Chapter 4 Removal and replacement procedures
Bluetooth module
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth
module cable is available using spare part number 489822-001.
Description
Spare part number
For use only with computer models equipped with AMD processors
412766-002
For use only with computer models equipped with Intel processors
483113-001
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 69).
6.
Remove the speaker assembly (see Speaker assembly on page 74).
Remove the Bluetooth module:
1.
Remove the Phillips PM2.0×4.0 screw (1) that secures the Bluetooth module to the top cover.
2.
Release the Bluetooth module (2) as far from the top cover as the Bluetooth module cable allows.
3.
Disconnect the Bluetooth module cable (3) from the Bluetooth module.
4.
Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures
75
Display assembly
NOTE: All display assemblies include a webcam, 2 microphones, and 2 wireless antenna transceivers
and cables.
Description
Spare part number
15.4-inch WSXGA+ AntiGlare display assembly
484372-001
15.4-inch WSXGA+ BrightView display assembly
484368-001
15.4-inch WXGA AntiGlare display assembly
484371-001
15.4-inch WXGA Brightview display assembly
484367-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 65).
6.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 69).
7.
Remove the speaker assembly (see Speaker assembly on page 74).
Remove the display assembly:
1.
76
Disconnect the display panel cable (1) and the webcam/microphone cable (2) from the system
board.
Chapter 4 Removal and replacement procedures
2.
Remove the WLAN antenna cables from the clips (3) built into the top cover.
CAUTION: Support the display assembly when removing the following screws. Failure to support
the display assembly can result in damage to the display assembly and other computer
components.
3.
Remove the four Phillips PM2.5×7.0 screws (1) that secure the display assembly to the computer.
4.
Remove the display assembly (2).
NOTE: Steps 5 through 22 provide display assembly internal component removal information for
computer models equipped with AntiGlare display assemblies. See steps 23 through 32 for display
assembly internal component removal information for computer models equipped with BrightView
display assemblies.
NOTE: See Webcam/microphone module on page 53 for webcam/microphone module
replacement instructions for computer models equipped with BrightView display assemblies.
Component replacement procedures
77
5.
If it is necessary to replace the display enclosure or any of the display assembly internal
components, remove the following screw covers and screws:
(1) Two rubber screw covers on the display bezel bottom edge. The display rubber screw covers
are included in the Display Rubber Kit, spare part number 486537-001.
(2) Two Phillips PM2.5×7.0 screws.
6.
Turn the display assembly upside down, with the bottom toward you.
7.
Release the display enclosure (1) by sliding the enclosure toward the top of the display assembly.
8.
Lift the display enclosure (2) as far as the display logo cable allows.
9.
Disconnect the display logo cable (3) from the display panel cable.
10. Remove the display enclosure. The display enclosure is available using spare part number
485345-001, and includes the display logo LED board and the wireless antenna transceivers and
cables.
11. If it is necessary to replace the webcam/microphone module, remove the Phillips PM2.0×4.0
screw (1) that secures the module to the display bezel.
78
Chapter 4 Removal and replacement procedures
12. Release the webcam/microphone module (2) as far as the webcam/microphone module cable
allows.
13. Disconnect the webcam/microphone module cable (3) from the webcam/microphone module.
14. Remove the webcam/microphone module. The webcam/microphone module is available using
spare part number 485345-001.
15. If it is necessary to replace the display inverter, remove the four Phillips PM2.5×4.0 screws (1) that
secure the display inverter cover to the display bezel.
16. Remove the display inverter cover (2) by lifting it straight up. The display inverter cover is available
using spare part number 486792-001.
17. Release the display inverter (1) as far from the display bezel as far as the display panel cable and
backlight cable allow.
Component replacement procedures
79
18. Disconnect the display panel cable (2) and backlight cable (3) from the display inverter.
19. Remove the display inverter. The display inverter is available using spare part number
488317-001.
20. If it is necessary to replace the display hinges, remove the four Phillips PM2.5×4.0 screws (1) that
secure the display hinges to the display panel.
21. Remove the display hinge (2) by lifting it straight up. The display hinge is available using spare part
number 485340-001.
NOTE: Steps 23 through 32 provide display assembly internal component removal information
for computer models equipped with BrightView display assemblies. See steps 5 through 22 for
display assembly internal component removal information for computer models equipped with
AntiGlare display assemblies.
NOTE: See Webcam/microphone module on page 53 for webcam/microphone module
replacement instructions for computer models equipped with BrightView display assemblies.
80
Chapter 4 Removal and replacement procedures
22. If it is necessary to replace the display bezel or any of the display assembly internal components,
remove the following screw covers and screws:
(1) Two rubber screw covers on the display bezel bottom edge. The display rubber screw covers
are included in the Display Rubber Kit, spare part number 480442-001.
(2) Two Phillips PM2.5×7.0 screws.
23. Flex the inside edges of the top edge (1), the left and right sides (2), and the bottom edge of the
display bezel (3) until the bezel disengages from the display enclosure.
24. Remove the display bezel (4). The display bezel is available using the spare part number
486532-001.
25. If it is necessary to replace the display inverter, release the display inverter (1) as far from the
display enclosure as far as the display panel cable and backlight cable allow.
Component replacement procedures
81
26. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
27. Remove the display inverter. The display inverter is available using spare part number
488317-001.
28. If it is necessary to replace the display panel, remove the six Phillips PM2.5×4.0 screws (1) that
secure the display panel to the display enclosure.
29. Remove the display panel (2). Display panels are available using spare part numbers 484363-001
(WSXGA+ BrightView display panel) and 484364-001 (WXGA BrightView display panel).
30. If it is necessary to replace the display hinges, remove the six Phillips PM2.0×4.0 screws (1) that
secure each display hinge to the display panel.
82
Chapter 4 Removal and replacement procedures
31. Remove the display hinges (2). The display hinges are available in the Display Hinge Kit, spare
part 486534-001. The display hinge screws are available in the Display Hinge Kit Screw Kit, spare
part number 485344-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
83
Top cover
Description
Spare part number
For use only with computer models equipped with a fingerprint reader
486527-001
For use only with computer models not equipped with a fingerprint reader
486526-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62)
b.
Optical drive (see Optical drive on page 55)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69)
d.
Speaker assembly (see Speaker assembly on page 74)
e.
Display assembly (see Display assembly on page 76)
Remove the top cover:
84
1.
Turn the computer upside down, with the front toward you.
2.
Remove the 12 Phillips PM2.5×7.0 screws that secure the top cover to the computer.
Chapter 4 Removal and replacement procedures
3.
Remove the three Phillips PM2.5×4.0 screws secure the top cover to the computer.
4.
Turn the computer right-side up, with the front toward you.
5.
Disconnect the following cables from the system board:
(1) Bluetooth module cable
(2) TouchPad cable
NOTE: On computer models equipped with a standard display assembly, this cable connects to
a ZIF connector on the system board. On computer models equipped with a Flush Glass display
assembly, this cable connects to a LIF connector on the system board.
(3) Fingerprint reader board cable
6.
NOTE:
This cable connects to a LIF connector on the system board.
NOTE:
Step 6 applies only to computer models equipped with standard display assemblies.
Remove the two Phillips PM2.5×7.0 screws (1) that secure the top cover to the computer.
Component replacement procedures
85
7.
Remove the two Phillips PM2.5×6.0 screws (2) that secure the top cover to the computer.
8.
Lift the rear edge of the top cover (1) until it rests at an angle.
9.
Remove the top cover (2) by lifting it straight up.
Reverse this procedure to install the top cover.
86
Chapter 4 Removal and replacement procedures
Modem module
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 501891-001. See Cable Kit on page 31 for more
Cable Kit spare part number information.
Description
Spare part number
Modem module for use in all countries and regions except Australia and New Zealand
461749-001
For use only in Australia and New Zealand
461749-011
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
Remove the modem module:
1.
Disconnect the modem module cable (1) from the modem module.
2.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the modem module to the system board.
Component replacement procedures
87
3.
Lift the modem module (3) straight up to disconnect it from the system board.
Reverse this procedure to install the modem module.
88
Chapter 4 Removal and replacement procedures
Audio/infrared board
Description
Spare part number
Audio/infrared board (includes cable)
486797-001
Before removing the audio/infrared board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
Remove the audio/infrared board:
1.
Disconnect the audio/infrared board cable (1) from the LIF connector on the system board.
2.
Release the clip (2) built into the base enclosure that secures the audio/infrared board.
3.
Lift the audio/infrared board (3) straight up to remove it from the base enclosure.
Component replacement procedures
89
Reverse this procedure to install the audio/infrared board.
USB board
Description
Spare part number
USB board (includes cable)
486798-001
Before removing the USB board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
Remove the USB board:
90
1.
Disconnect the USB board cable (1) from the LIF connector on the system board.
2.
Remove the Phillips PM2.5×7.0 screw (2) that secures the USB board to the base enclosure.
Chapter 4 Removal and replacement procedures
3.
Remove the USB board (3) from the base enclosure.
Reverse this procedure to install the USB board.
Component replacement procedures
91
System board
NOTE:
All system board spare kits include replacement thermal material.
Description
Spare part number
For use only with computer models equipped with AMD processors:
With RX781 Northbridge and ATI-M82-S discrete graphics subsystem memory
482324-001
With RS780 Northbridge and ATI-M UMA graphics subsystem memory
482325-001
For use only with computer models equipped with Intel processors:
With PM45 Northbridge and nVidia NB9P-GS discrete graphics subsystem memory
482870-001
With PM45 Northbridge and nVidia NB9M-GE discrete graphics subsystem memory
482867-001
With GM45 Northbridge and UMA graphics subsystem memory
482869-001
With ICH9M Northbridge and UMA graphics subsystem memory
482868-001
Before removing the system board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62)
b.
Optical drive (see Optical drive on page 55)
c.
Switch cover (see Switch cover and keyboard on page 69)
d.
Speaker assembly (see Speaker assembly on page 74)
e.
Display assembly (see Display assembly on page 76)
f.
Top cover (see Top cover on page 84)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
92
●
TV tuner module (see TV tuner module on page 57)
●
RTC battery (see RTC battery on page 59)
●
Memory modules (see Memory module on page 60)
●
WLAN module (see Bluetooth module on page 75)
●
Modem module (see Modem module on page 87)
Chapter 4 Removal and replacement procedures
●
Fan/heat sink assembly (see System board on page 92)
●
Processor (see System board on page 92)
Remove the system board:
1.
Disconnect the modem module cable (1) from the modem module.
2.
Disconnect the following cables from the system board:
(2) Audio/infrared board cable
NOTE:
The audio/infrared board cable connects to a LIF connector on the system board.
(3) USB board cable
NOTE:
The USB board cable connects to a LIF connector on the system board.
(4) Power connector cable
3.
Remove the Phillips PM2.5×7.0 screw (1) that secures the system board to the base enclosure.
4.
Use the optical drive connector (2) to lift the right side of the system board (3) until it rests at an
angle.
5.
Remove the system board (4) by sliding it up and to the right at an angle.
Component replacement procedures
93
Reverse the preceding procedure to install the system board.
TV tuner module cable
NOTE:
The TV tuner module cable is available in the Cable Kit, spare part number 501891-001.
Before removing the TV tuner module cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
g.
USB board (see USB board on page 90).
h.
System board (see System board on page 92).
Remove the TV tuner module cable:
94
1.
Release the clips (1) built into the base enclosure that secure the TV tuner antenna connector.
2.
Remove the TV tuner antenna connector (2) from the clip built into the base enclosure.
Chapter 4 Removal and replacement procedures
3.
Remove the TV tuner module cable (3) from the clips and routing channel built into the base
enclosure.
Reverse this procedure to install the TV tuner module cable.
Modem module cable
NOTE: The modem module cable is available in the Cable Kit, spare part number 501891-001. The
modem module cable includes the RJ-11 jack.
Before removing the modem module cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
g.
USB board (see USB board on page 90).
h.
System board (see System board on page 92).
Component replacement procedures
95
Remove the modem module cable:
1.
Release the clips (1) built into the base enclosure that secure the RJ-11 jack.
2.
Remove the RJ-11 jack (2) from the clip built into the base enclosure.
3.
Remove the modem module cable (3) from the clips and routing channel built into the base
enclosure.
Reverse this procedure to install the modem module cable.
Power connector cable
NOTE:
The power connector cable is available in the Cable Kit, spare part number 501891-001.
Before removing the power connector cable, follow these steps:
96
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
Chapter 4 Removal and replacement procedures
g.
USB board (see USB board on page 90).
h.
System board (see System board on page 92).
Remove the power connector cable:
1.
Remove the power connector cable (1) from the clips and routing channel built into the base
enclosure.
2.
Remove the Phillips PM2.5×7.0 screw (2) that secures the power connector and bracket to the
base enclosure.
3.
Remove the power connector bracket (3).
4.
Remove the power connector cable (4).
Reverse this procedure to install the power connector cable.
Component replacement procedures
97
Fan/heat sink assembly
NOTE:
All fan/heat sink assembly spare kits include replacement thermal material.
Description
Spare part number
For use only with computer models equipped with AMD processors and graphics subsystems with
discrete memory
493001-001
For use only with computer models equipped with AMD processors and graphics subsystems with
UMA memory
491572-001
For use only with computer models equipped with Intel processors and graphics subsystems with
discrete memory
486799-001
For use only with computer models equipped with Intel processors and graphics subsystems with
UMA memory
492314-001
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side
and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled
by a temperature sensor and is designed to turn on automatically when high temperature conditions
exist. These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software applications.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
98
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
g.
USB board (see USB board on page 90).
h.
System board (see System board on page 92).
Chapter 4 Removal and replacement procedures
Remove the fan/heat assembly:
1.
Turn the system board upside down, with the expansion port 3 and external monitor port toward
you.
NOTE: Steps 2 through 4 apply only to computer models equipped with graphics subsystems
with discrete memory.
2.
Disconnect the fan cable (1) from the system board.
3.
Loosen the three Phillips PM2.0×10.0 captive screws (2) that secure the fan/heat sink assembly
to the system board.
4.
Remove the fan/heat sink assembly (3).
NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
NOTE: Steps 5 through 7 apply only to computer models equipped with graphics subsystems
with UMA memory.
5.
Disconnect the fan cable (1) from the system board.
6.
Loosen the three Phillips PM2.0×10.0 captive screws (2) that secure the fan/heat sink assembly
to the system board.
Component replacement procedures
99
7.
Remove the fan/heat sink assembly (3).
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach
the assembly.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly and the system board each time the fan/heat sink assembly is removed. Thermal paste is
used on the processor (1) and the heat sink section (2) that services it. Thermal pads are used on the
Northbridge chip (3), the graphics subsystem chip (4), and the sections of the heat sink (5) that service
them. Replacement thermal material is included with all fan/heat sink assembly, system board, and
processor spare part kits.
The following illustration shows the replacement thermal material locations for computer models
equipped with graphics subsystems with discrete memory.
100 Chapter 4 Removal and replacement procedures
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly and the system board each time the fan/heat sink assembly is removed. Thermal paste is
used on the processor (1) and the heat sink section (2) that services it. Thermal pads are used on the
Northbridge chip (3) and the section of the heat sink (4) that services it. Replacement thermal material
is included with all fan/heat sink assembly, system board, and processor spare part kits.
The following illustration shows the replacement thermal material locations for computer models
equipped with graphics subsystems with UMA memory.
Reverse this procedure to install the fan/heat sink assembly.
Component replacement procedures 101
Processor
NOTE:
All processor spare part kits include thermal material.
Description
Spare part number
AMD Turion Ultra Dual-Core 35W ZM-86 2.40-GHz processor with 2-MB L2 cache
484260-001
AMD Turion Ultra Dual-Core 35W ZM-82 2.20-GHz, processor with 2-MB L2 cache
484261-001
AMD Turion Ultra Dual-Core 35W ZM-80 2.10-GHz, processor with 2-MB L2 cache
484262-001
AMD Turion Dual-Core 35W RM-70 2.00-GHz with 1-MB L2 cache processor
484263-001
AMD Athlon X2 Dual-Core 35W QL-60 1.90-GHz with 1-MB L2 cache processor
484264-001
Intel Core2 Duo T9600 2.80-GHz processor with 6-MB L2 cache and 1066-MHz FSB
483859-001
Intel Core2 Duo T9400 2.53-GHz processor with 6-MB L2 cache and 1066-MHz FSB
483860-001
Intel Core Duo T8600 2.40-GHz processor with 3-MB L2 cache and 1066-MHz FSB
483861-001
Intel Core Duo T8400 2.26-GHz processor with 3-MB L2 cache and 1066-MHz FSB
486523-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 52).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 62).
b.
Optical drive (see Optical drive on page 55).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 69).
d.
Speaker assembly (see Speaker assembly on page 74).
e.
Display assembly (see Display assembly on page 76).
f.
Top cover (see Top cover on page 84).
g.
USB board (see USB board on page 90).
h.
System board (see System board on page 92).
i.
Fan/heat sink assembly (see Fan/heat sink assembly on page 98).
Remove the processor:
102 Chapter 4 Removal and replacement procedures
NOTE: Steps 1 and 2 apply only to computer models equipped with AMD processors. See steps 3
and 4 for processor removal information for computer models equipped with Intel processors.
1.
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
2.
Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
NOTE: Steps 3 and 4 apply only to computer models equipped with Intel processors. See steps
1 and 2 for processor removal information for computer models equipped with AMD processors.
3.
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
4.
Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
Component replacement procedures 103
5
Setup Utility
WARNING! Only authorized technicians trained by HP must repair this equipment. All troubleshooting
and repair procedures are detailed to allow repair at only the subassembly or module level. Because of
the complexity of the individual boards and subassemblies, do not attempt to make repairs at the
component level or modify any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modification may void any warranty or
exchange allowances.
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working.
NOTE:
The fingerprint reader (select models only) cannot be used to access the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and
other preferences.
To start the Setup Utility:
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc.
2.
When the Startup Menu is displayed, press f10.
104 Chapter 5 Setup Utility
Using the Setup Utility
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Use the arrow keys to select a language, and then press enter.
4.
When a confirmation prompt with your language selected is displayed, press enter.
5.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.
Display system information
The following procedure explains how to display system information in the Setup Utility. If the Setup
Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3.
To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.
Using the Setup Utility 105
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter.
4.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
The Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Exiting the Setup Utility
You can exit the Setup Utility with or without saving changes.
●
To exit the Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
●
To exit the Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Discarding Changes, and then press enter.
After either choice, the computer restarts in Windows.
106 Chapter 5 Setup Utility
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by
your computer.
Main menu
Select
To do this
System information
●
View and change the system time and date.
●
View identification information about the computer.
●
View specification information about the processor, memory size, system BIOS,
and keyboard controller version (select models only).
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On Password
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Change the Setup Utility language.
Button Sound (select models only)
Enable/disable the capacitive button tapping sound.
Virtualization Technology
Enable/disable the processor Virtualization Technology.
Processor C4 State (select
models only)
Enable/disable the processor C4 sleep state.
LAN Power Saving (select
models only)
Enable/disable LAN Power Saving. When enabled, saves power when the computer
is in DC mode.
Card Reader/1394 Power Saving (select
models only)
Enable/disable Card Reader/1394 Power Saving. When enabled, saves power when
the computer is in DC mode.
Fan Always On
Enabled/disable Fan Always On. When enabled, the computer fan will always be on.
Boot Options
Set the following boot options:
●
f9 and f10 Delay (sec.)―Set the delay for the f9 and f10 functions of the Setup
Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
●
CD-ROM boot―Enable/disable boot from CD-ROM.
●
Floppy boot―Enable/disable boot from diskette.
Setup Utility menus 107
Select
To do this
●
Internal Network Adapter boot―Enable/disable boot from Internal
Network Adapter.
●
Boot Order―Set the boot order for:
◦
USB Floppy
◦
Internal CD/DVD ROM Drive
◦
Hard drive
◦
USB Diskette on Key
◦
USB Hard drive
◦
Network adapter
Diagnostics menu
Select
To do this
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
NOTE: On models with two hard drives, this menu option is called the Primary Hard
Disk Self Test.
Secondary Hard Disk Self Test (select
models only)
Run a comprehensive self-test on a secondary hard drive.
Memory Test
Run a diagnostic test on the system memory.
108 Chapter 5 Setup Utility
6
Specifications
Computer specifications
Metric
U.S.
Width
35.70 cm
14.06 in
Depth
25.94 cm
10.21 in
Height (front to back)
3.49 to 4.19 cm
1.37 to 1.65 in
Weight (with optical drive, hard drive,
and battery)
2.82 kg
6.82 lbs
Second hard drive adds:
0.13 kg
0.28 lbs
Camera adds:
0.009 kg
0.02 lbs
Dimensions
Input power
Operating voltage
18.5 V dc @ 3.5 A - 65 W
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Computer specifications 109
Metric
U.S.
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Nonoperating
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
15.4-inch, SXGA+ display specifications
Metric
U.S.
Height
20.7 cm
8.15 in
Width
33.1 cm
13.03 in
Diagonal
39.1 cm
15.39 in
Number of colors
Up to 16.8 million
Contrast ratio
200:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.197 × 0.197 mm
Format
1680 × 1050
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4W
Viewing angle
+/-65° horizontal, +/-50° vertical (typical)
110 Chapter 6 Specifications
15.4-inch WXGA display specifications
Metric
U.S.
Height
20.7 cm
8.15 in
Width
33.1 cm
13.03 in
Diagonal
39.1 cm
15.39 in
Number of colors
Up to 16.8 million
Contrast ratio
200:1
Brightness
150 nits typical
Dimensions
Pitch resolution
Pitch
0.259 × 0.259 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4W
Viewing angle
+/-65° horizontal, +/–50° vertical typical
15.4-inch WXGA display specifications 111
Hard drive specifications
320-GB*
250-GB*
160-GB*
120-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
101 g
Interface type
ATA-7
ATA-7
ATA-7
ATA-7
Synchronous (maximum)
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
Dimensions
Transfer rate
Seek times (typical read, including setting)
Single track
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
Logical blocks
625,141,400
488,397,168
312,581,808
234,441,648
Disc rotational speed
5400-rpm
5400-rpm
7200-rpm and
5400-rpm
5400-rpm
Operating temperature
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
112 Chapter 6 Specifications
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW
Double-Layer
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CDTEXT,
CD-ROM, CD-ROM XA,
MIXED MODE CD, CD-I, CD-I Bridge
(Photo-CD, Video CD), Multisession CD
(Photo-CD, CD-EXTRA, Portfolio, CDR, CD-RW), CD-R, CD-RW,
DVDROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-RAM, HDROM (Single Layer), HD-ROM (Dual
Layer), HD DVD-R, HD DVD-R for
Dual Layer, HD DVD-RW
CD-R and CD-RW DVD+R, DVD+R(9),
DVD+RW, DVD-R, DVD-R(9),DVD-RW,
DVD-RAM
Access time
CD
DVD
HD
Random
170 ms
170 ms
230 ms
Cache buffer
8 MB
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
1X BD-ROM
4,500 KB/sec
1X BD-R read
4,500 KB/sec
1X BD-RE read
4,500 KB/sec
Transfer mode
Multiword DMA Mode
Blu-ray Disc ROM Drive with SuperMulti DVD±R/RW Double-Layer 113
DVD±RW and CD-RW Super Multi Double-Layer Combo
Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CDCD-R and CD-RW
TEXT, CD-ROM, CD-ROM XA, MIXED
MODE CD, CD-I, CD-I Bridge (Photo- DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
CD, Video CD), Multisession CD
(Photo-CD, CD-EXTRA, Portfolio, CDR, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-RAM
Center hole diameter
1.5 cm (0.59 in)
Disc diameter
Standard disc
12 cm (4.72 in)
Mini disc
8 cm (3.15 in)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Full stroke
< 285 ms
< 335 ms
Audio output level
Audio-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
Startup time
< 15 seconds
Stop time
< 6 seconds
114 Chapter 6 Specifications
System DMA specifications, AMD
Hardware DMA
System function
DMA4
Direct memory access controller
System DMA specifications, Intel
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for PC Card
DMA6
Not assigned
DMA7
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
System DMA specifications, AMD 115
System interrupt specifications, AMD discrete graphics
Hardware
IRQ System function
IRQ0
High precision event timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural PS/2 Keyboard
IRQ5
RICOH OHCI Compliant IEEE 1394 Host Controller
IRQ7
Ricoh Memory Stick Controller
Ricoh SD/MMC Host Controller
Ricoh XD-Picture Card Controller
SDA Standard Compliant SD Host Controller
IRQ8
High precision event timer
IRQ10
nVidia nForce PCI System Management
IRQ11
nVidia nForce System Management Controller
IRQ12
Synaptics PS/2 Port TouchPad
IRQ13
Numeric data processor
IRQ14
ATA Channel 0
IRQ15
ATA Channel 1
IRQ16
Broadcom WLAN adapter
IRQ17
Standard Enhanced PCI to USB Host Controller
IRQ18
Standard OpenHCD USB Host Controller
IRQ19
nVidia GeForce8400M GS
IRQ20
nVidia nForce Networking Controller
IRQ21
HDA Controller
IRQ23
Standard Dual Channel PCI IDE Controller
116 Chapter 6 Specifications
System interrupt specifications, AMD UMA graphics
Hardware
IRQ System function
IRQ0
High precision event timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural PS/2 Keyboard
IRQ5
RICOH OHCI Compliant IEEE 1394 Host Controller
IRQ7
Ricoh Memory Stick Controller
Ricoh SD/MMC Host Controller
Ricoh XD-Picture Card Controller
SDA Standard Compliant SD Host Controller
IRQ8
High precision event timer
IRQ10
nVidia nForce PCI System Management
IRQ11
nVidia nForce System Management Controller
IRQ12
Synaptics PS/2 Port TouchPad
IRQ13
Numeric data processor
IRQ14
ATA Channel 0
IRQ15
ATA Channel 1
IRQ16
nVidia MCP67M
IRQ18
Standard OpenHCD USB Host Controller
Standard OpenHCD USB Host Controller
IRQ19
Broadcom WLAN adapter
IRQ21
HDA Controller
IRQ22
Standard Enhanced PCI to USB Host Controller
Standard Enhanced PCI to USB Host Controller
IRQ23
Standard Dual Channel PCI IDE Controller
System interrupt specifications, AMD UMA graphics 117
System interrupt specifications, Intel
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port
may assert IRQ3 or IRQ4.
118 Chapter 6 Specifications
System I/O address specifications, AMD
I/O address (hex)
System function (shipping configuration)
0000 - 0008
DMA controller
000A - 000F
DMA controller
0020 - 0021
Programmable interrupt controller
0040 - 0043
System timer
0060 - 0060
Standard 101-/102-Key or Microsoft® Natural PS/2 Keyboard
0061 - 0061
System speaker
0062 - 0062
Microsoft ACPI-Compliant Embedded Controller
0064 - 0064
Standard 101-/102-Key or Microsoft® Natural PS/2 Keyboard
0066 - 0066
Microsoft ACPI-Compliant Embedded Controller
0070 - 0071
System CMOS/real time clock
0081 - 0083
DMA controller
0087 - 0087
DMA controller
0089 - 008B
DMA controller
008F - 008F (UMA only)
DMA controller
00A0 - 00A1
Programmable interrupt controller
00C0 - 00D1
DMA controller
00D4 - 00DF
DMA controller
00F0 - 00F1
Numeric data processor
0170 - 0177
ATA Channel 1
01F0 - 01F7
ATA Channel 0
0376 - 0376
ATA Channel 1
03B0 - 03BB
nVidia GeForce8400M GS (discrete)
nVidia MCP67M (UMA)
03B0 - 03BB (discrete only)
PCI standard PCI-to-PCI bridge
03C0 - 03DF
nVidia GeForce8400M GS (discrete)
nVidia MCP67M (UMA)
03C0 - 03DF (discrete only)
PCI standard PCI-to-PCI bridge
03F6 - 03F6
ATA Channel 0
3000 - 303F
nVidia nForce PCI System Management
3040 - 307F
nVidia nForce PCI System Management
3080 - 30BF
nVidia nForce PCI System Management
30C0 - 30CF
Standard Dual Channel PCI IDE Controller
30D0 - 30DF
Standard Dual Channel PCI IDE Controller
System I/O address specifications, AMD 119
I/O address (hex)
System function (shipping configuration)
30E0 - 30E3 (UMA only)
Standard Dual Channel PCI IDE Controller
30E8 - 30EB
Standard Dual Channel PCI IDE Controller
30EC - 30EF
Standard Dual Channel PCI IDE Controller
30F0 - 30F7
Standard Dual Channel PCI IDE Controller
30F8 - 30FF (discrete only)
Standard Dual Channel PCI IDE Controller
4000 - 407F (discrete only)
nVidia GeForce8400M GS
4000 - 4FFF
PCI standard PCI-to-PCI bridge
5000 - 5FFF (discrete only)
PCI standard PCI-to-PCI bridge
120 Chapter 6 Specifications
System I/O address specifications, Intel
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System Function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
System I/O address specifications, Intel 121
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
PC Card controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
122 Chapter 6 Specifications
System memory map specifications, AMD discrete
graphics
Size
Memory address
System function
128 KB
000A0000-000BFFFF
nVidia GeForce8400M GS
16 KB
B0000000-B0003FFF
HDA Controller
8 KB
B0004000-B0005FFF
Standard Dual Channel PCI IDE
Controller
4 KB
B0006000-B0006FFF
Standard OpenHCD USB Host Controller
256 B
B0007000-B00070FF
Standard Enhanced PCI to USB Host
Controller
4 KB
B0008000-B0008FFF
nVidia nForce Networking Controller
512 KB
B0080000-B00FFFFF
nVidia nForce System Management
Controller
2 KB
B0100000-B01007FF
RICOH OHCI Compliant IEEE 1394 Host
Controller
256 B
B0100800-B01008FF
SDA Standard Compliant SD Host
Controller
256 B
B0100C00-B0100CFF
Ricoh SD/MMC Host Controller
256 B
B0101000-B01010FF
Ricoh Memory Stick Controller
256 B
B0101400-B01014FF
Ricoh XD-Picture Card Controller
16 KB
B0200000-B0203FFF
Broadcom WLAN adapter
16 MB
B1000000-B1FFFFFF
nVidia GeForce8400M GS
32 MB
B2000000-B3FFFFFF
nVidia GeForce8400M GS
1 MB
B6000000-B60FFFFF
Broadcom WLAN adapter
256 MB
C0000000-CFFFFFFF
nVidia GeForce8400M GS
1 KB
FED00000-FED003FF
High precision event timer
System memory map specifications, AMD discrete graphics 123
System memory map specifications, AMD UMA graphics
Size
Memory address
System function
128 KB
000A0000-000BFFFF
nVidia MCP67M
16 KB
B0000000-B0003FFF
HDA Controller
8 KB
B0004000-B0005FFF
Standard Dual Channel PCI IDE
Controller
4 KB
B0006000-B0006FFF
Standard OpenHCD USB Host Controller
256 B
B0007000-B00070FF
Standard Enhanced PCI to USB Host
Controller
256 B
B0007400-B00074FF
Standard Enhanced PCI to USB Host
Controller
16 B
B0007800-B000780F
nVidia nForce Networking Controller
256 B
B0007C00-B0007CFF
nVidia nForce Networking Controller
4 KB
B0008000-B0008FFF
Standard OpenHCD USB Host Controller
4 KB
B0009000-B0009FFF
nVidia nForce Networking Controller
512 KB
B0080000-B00FFFFF
nVidia nForce System Management
Controller
16 MB
B1000000-B1FFFFFF
nVidia MCP67M
16 MB
B2000000-B2FFFFFF
nVidia MCP67M
2 KB
B3000000-B30007FF
RICOH OHCI Compliant IEEE 1394 Host
Controller
256 B
B3000800-B30008FF
SDA Standard Compliant SD Host
Controller
256 B
B3000C00-B3000CFF
Ricoh SD/MMC Host Controller
256 B
B3001000-B30010FF
Ricoh Memory Stick Controller
256 B
B3001400-B30014FF
Ricoh XD-Picture Card Controller
16 KB
B6000000-B6003FFF
Broadcom WLAN adapter
256 KB
C0000000-CFFFFFFF
nVidia MCP67M
1 KB
FED00000-FED003FF
High precision event timer
124 Chapter 6 Specifications
System memory map specifications, Intel
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications, Intel 125
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in
the computer. All screws and screw locks listed in this section are available in the Screw Kit, spare part
numbers 486795-001 and 493002-001, and the Display Screw Kit, spare part number 485343-001.
126 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
30
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Two screws that secure the keyboard to the computer
(3) Two screws that secure the switch cover to the computer
Phillips PM2.5×7.0 screw 127
Where used: 4 screws that secure the display assembly to the computer
Where used: 2 screws that secure the display bezel to the display enclosure on computer models
equipped with BrightView display assemblies
Where used: 2 screws that secure the display bezel to the display enclosure on computer models
equipped with AntiGlare display assemblies
128 Chapter 7 Screw listing
Where used: 12 screws that secure the top cover to the base enclosure
Where used: 2 screws that secure the top cover to the base enclosure (only on computer models
equipped with a standard display assembly)
Where used: One screw that secures the USB board to the base enclosure
Phillips PM2.5×7.0 screw 129
Where used: One screw that secures the system board to the base enclosure
Where used: One screw that secures the power connector and bracket to the base enclosure
130 Chapter 7 Screw listing
Phillips PM2.5×6.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
6.0 mm
2.5 mm
5.0 mm
Where used:
(1) One captive screw that secures the Mini Card module compartment cover to the computer (screw
is secured by a C-clip)
(2) One captive screw that secures the memory module compartment cover to the computer (screw is
secured by a C-clip)
(3) Two captive screws that secure the hard drive bay compartment cover to the computer (screws are
secured by C-clips)
Phillips PM2.5×6.0 captive screw 131
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
18
4.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Where used:
(1) Two screws that secure the TV tuner module to the system board
(2) Two screws that secure the WLAN module to the system board
132 Chapter 7 Screw listing
Where used: 3 screws that secure the switch cover to the computer
Where used: 4 screws that secure the keyboard to the computer
Where used: One screw that secures the power button board to the switch cover
Phillips PM2.0×4.0 screw 133
Where used: One screw that secures the Bluetooth module to the top cover
Where used: One screw that secures the webcam/microphone module to the display bezel on computer
models equipped with AntiGlare display assemblies
Where used: 2 screws that secure the modem module to the system board
134 Chapter 7 Screw listing
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
6
4.0 mm
2.0 mm
4.5 mm
Where used: 6 screws that secure the display hinges to the display panel on computer models equipped
with BrightView display assemblies
Phillips PM2.0×4.0 screw 135
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
19
4.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the display inverter cover to the display bezel on computer models
equipped with AntiGlare display assemblies
Where used: 4 screws that secure the display hinges to the display panel on computer models equipped
with AntiGlare display assemblies
136 Chapter 7 Screw listing
Where used: 6 screws that secure the display panel to the display enclosure on computer models
equipped with BrightView display assemblies
Where used: 2 screws that secure the wireless antenna transceivers to the display enclosure on
computer models equipped with BrightView display assemblies
Where used: 3 screws that secure the top cover to the base enclosure
Phillips PM2.5×4.0 screw 137
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
138 Chapter 7 Screw listing
Phillips PM2.5×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
4
6.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the top cover to the base enclosure
Phillips PM2.5×6.0 screw 139
Phillips PM2.0×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
6
10.0 mm
2.0 mm
5.0 mm
Where used: 3 captive screws that secure the fan/heat sink assembly to the system board on computer
models equipped with graphics subsystems with discrete memory
140 Chapter 7 Screw listing
Where used: 3 captive screws that secure the fan/heat sink assembly to the system board on computer
models equipped with graphics subsystems with UMA memory
Phillips PM2.0×10.0 captive screw 141
8
Backup and Recovery
Recovering system information
Recovery after a system failure is as complete as your most current backup. HP recommends that you
create recovery discs immediately after software setup. As you add new software and data files, you
should continue to back up your system on a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●
Making a set of recovery discs (Recovery Manager software feature). Recovery discs are used to
start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●
Backing up your information regularly to protect your important system files.
●
Creating system restore points (operating system feature). System restore points allow you to
reverse undesirable changes to your computer by restoring the computer to an earlier state.
●
Recovering a program or driver (Recovery Manager software feature). This feature helps you
reinstall a program or driver without performing a full system recovery.
●
Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition (select models only) on the hard drive or from
recovery discs you create.
NOTE: If your computer includes a solid-state drive (SSD), you may not have a recovery partition.
Recovery discs have been included for computers that do not have a partition. Use these discs to recover
your operating system and software. To check for the presence of a recovery partition, select Start >
Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk Drives section of
the window.
142 Chapter 8 Backup and Recovery
Creating recovery discs
NOTE: HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE: Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●
You will need high quality CD-R, DVD-R, double-layer DVD-R, DVD+R, double-layer DVD+R, or
BD-R (writable Blu-ray) discs. All these discs are purchased separately.
NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE
(rewritable Blu-ray) discs, are not compatible with the Recovery Manager software.
●
The computer must be connected to AC power during this process.
●
Only one set of recovery discs can be created per computer.
●
Number each disc before inserting it into the computer optical drive.
●
If necessary, you can exit the program before you have finished creating the recovery discs. The
next time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
NOTE: If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
3.
Click Recovery disc creation, and then click Next.
4.
Follow the on-screen instructions.
Recovering system information 143
Backing up your information
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using Recovery Manager.
●
Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document, follow these steps:
1.
Display the screen.
2.
Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3.
Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
144 Chapter 8 Backup and Recovery
When to create restore points
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE:
If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Under Automatic restore points, select the disk for which you want to create a restore point.
5.
Click Create.
The System Protection window opens.
6.
Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Click the System Restore button, and then click Next.
The System Restore window opens.
5.
Follow the on-screen instructions.
Backing up your information 145
Performing a recovery
NOTE: You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state drive
(SSD), you may not have a recovery partition. If that is the case, recovery discs have been included
with your computer. Use these discs to recover your operating system and software.
NOTE: Windows has its own built-in repair features, such as System Restore and driver roll-back
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE: Recovery Manager recovers only software that was preinstalled at the factory. Software not
provided with this computer must be downloaded from the manufacturer's Web site or reinstalled from
the disc provided by the manufacturer.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Recovering from the dedicated recovery partition (select models only)
NOTE: If your computer includes a solid-state drive (SSD), you may not have a recovery partition. You
will not be able to recover using this procedure. Recovery discs have been included for computers that
do not have a partition. Use these discs to recover your operating system and software.
On some models, you can perform a recovery from the partition on the hard drive from either the Start
button or f11.
To restore the system from the partition, follow these steps:
1.
Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
–or–
●
Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed
on the screen. Then select Recovery Manager.
2.
Click Advanced Options.
3.
Click System recovery, and then click Next.
4.
Follow the on-screen instructions.
146 Chapter 8 Backup and Recovery
9
Connector pin assignments
1394
Pin
Signal
1
Power
2
Ground
3
TPB-
4
TPB+
5
TPA-
6
TPA+
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
1394 147
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
148 Chapter 9 Connector pin assignments
HDMI
Pin
Signal
1
TMDS data 2+
2
TMDS data 2 shield
3
TMDS data 2–
4
TMDS data 1+
5
TMDS data 1 shield
6
TMDS data 1–
7
TMDS data 0+
8
TMDS data 0 shield
9
TMDS data 0–
10
TMDS clock+
11
TMDS clock shield
12
TMDS clock-
13
CEC
14
No connect
15
DDC clock
16
DDC data
17
Ground
18
+5V power
19
Hot plug detect
20
Shell
HDMI 149
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
150 Chapter 9 Connector pin assignments
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
Universal Serial Bus 151
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by each country or region’s power system.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
152 Chapter 10 Power cord set requirements
Requirements for specific countries or regions
Country or region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
South Korea
EK
4
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
Requirements for specific countries or regions 153
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or
see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from
one computer model to another.
154 Chapter 11 Recycling
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
Display 155
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
156 Chapter 11 Recycling
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
Display 157
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
18. Remove the backlight from the backlight frame.
158 Chapter 11 Recycling
19. Disconnect the display cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
Display 159
Index
Symbols/Numerics
1394 port
location 15
pin assignments 147
1394 Power Saving 107
A
AC adapter, spare part
numbers 34, 35, 37
administrator password 107
antenna
illustrated 29
locations 7
spare part numbers 29
applications key, Windows 11
audio, product description 4
audio-in jack
location 13
pin assignments 147
audio-out jack
location 13
pin assignments 148
audio/infrared board
removal 89
spare part number 20, 40,
89
B
backing up
customized window, toolbar,
and menu bar settings 144
personal files 144
templates 144
backup 142
backup suggestions 144
base enclosure, spare part
numbers 21, 40
160 Index
battery
removal 52
spare part numbers 22, 39,
52
battery bay 16
battery light 13
battery release latch 16
Blu-ray Disc ROM Drive
precautions 45
removal 55
spare part numbers 22, 32,
40, 55
specifications 113
Bluetooth module
removal 75
spare part numbers 19, 35,
38, 75
Bluetooth module cable
illustrated 31
spare part number 20, 42
boot options 107
boot order 107
bottom components 16
button components 9
button sound 107
buttons
media 9
next/fast forward 10
play/pause 10
power 9
previous/rewind 10
stop 10
volume mute 9
wireless 10
C
Cable Kit
contents 31
spare part number 20, 31,
43
cables, service considerations 45
Card Reader Power Saving 107
carrying case, spare part
numbers 34, 35
CAT5E cable, spare part
number 34, 36
changing the Setup Utility
language 105
chipset, product description 1
CMOS clearing 49
components
bottom 16
buttons 9
display 7
fingerprint reader 9
front 13
keyboard 11
left-side 15
rear 14
right-side 14
speakers 9
top 7
TouchPad 12
computer feet
locations 51
spare part number 51
computer specifications 109
connectors, service
considerations 45
D
Digital Media Slot 15
Digital Media Slot Light 15
diskette drive, precautions 45
display assembly
removal 76
spare part numbers 18, 39,
76
display bezel
illustrated 28
release 53
spare part number 28, 40,
81
Display Cable Kit, spare part
numbers 28, 43
display components
illustrated 27, 28
recycling 154
display enclosure
illustrated 27, 29
removal 78
spare part numbers 27, 29,
39, 40, 78
display hinge
illustrated 27, 28, 39
removal 80, 82
spare part numbers 27, 28,
39, 40, 80, 83
Display Hinge Kit, spare part
numbers 27, 28, 39, 40, 80,
83
Display Hinge Screw Kit, spare part
number 39
display inverter
illustrated 27, 29
removal 79, 81
spare part number 27, 29,
41, 80, 82
display inverter cover
illustrated 27, 40
removal 79
spare part number 27, 40,
79
display panel
illustrated 28
product description 2
removal 82
spare part numbers 28, 39,
82
display panel cable, spare part
numbers 40
Display Rubber Kit, spare part
number 27, 29, 40
Display Screw Kit, spare part
number 27, 29, 39
display specifications 110, 111
display switch 7
displaying system
information 105
docking support, product
description 5
drive light 13
drives
boot order 107
preventing damage 45
DVD±RW and CD-RW Combo
Drive
precautions 45
removal 55
spare part numbers 22, 33,
38, 55
specifications 114
E
electrostatic discharge 46
eSATA/USB port 15
esc key 11
Ethernet, product description 4
exiting the Setup Utility 106
expansion port 3 15
ExpressCard slot 15
ExpressCard slot bezel,
illustrated 30
external media cards, product
description 5
external monitor port
location 15
pin assignments 148
F
f11 146
fan always on 107
fan/heat sink assembly
removal 98
spare part numbers 21, 41,
43, 98
feet
locations 51
spare part number 51
fingerprint reader 10, 104
fingerprint reader components 9
fn key 11
front components 13
full system recovery 142
function keys 11
G
graphics, product description
grounding equipment and
methods 48
2
H
hard drive
precautions 45
product description 3
removal 62
spare part numbers 25, 32,
37, 42, 62
specifications 112
hard drive bay 16
hard drive bay cover
illustrated 30
removal 63
Hard Drive Hardware Kit, spare part
number 26, 32, 38, 62
hard drive self test 108
HDMI port
location 15
pin assignments 149
headphone jack
location 13
pin assignments 148
headset, spare part number 34,
35
hinge
illustrated 27, 28, 39
removal 80, 82
spare part numbers 27, 28,
39, 40, 80, 83
I
I/O address specifications 119,
121
infrared lens 13
interrupt specifications 116,
117, 118
J
jacks
audio-in 13
audio-out 13
headphone 13
microphone 13
modem 14
network 15
RJ-11 14
RJ-45 15
TV tuner antenna 14
K
keyboard
components 11
Index 161
product description 6
removal 69
spare part numbers 19, 41,
69
keypad keys 11
keys
embedded numeric
keypad 11
esc 11
fn 11
function 11
Windows applications 11
Windows logo 11
L
LAN Power Saving 107
language support 107
left-side components 15
lights
battery 13
Digital Media Slot 15
drive 13
optical drive 14
power 13
M
mass storage devices, spare part
numbers 32
media button 9
memory map specifications 123,
124, 125
memory module
product description 2
removal 60
spare part numbers 22, 39,
60
memory module compartment 16
memory module compartment
cover
illustrated 30
removal 60
memory test 108
microphone
locations 8
product description 4
microphone jack
location 13
pin assignments 147
Mini Card module
compartment 16
162 Index
Mini Card module compartment
cover
ilustrated 30
removal 57
model name 1
modem jack
location 14
pin assignments 150
modem module
removal 87
spare part numbers 20, 37,
87
modem module cable
illustrated 31
removal 95
modem, product description 4
monitor port
location 15
pin assignments 148
mouse, spare part numbers 34,
35
N
network jack
location 15
pin assignments 150
next/fast forward button 10
O
operating system, product
description 6
optical drive
location 14
precautions 45
product description 3
removal 55
spare part numbers 22, 32,
55
specifications 113, 114
optical drive light 14
P
packing guidelines 47
password clearing 49
passwords 107
performing a system
recovery 146
pin assignments
1394 147
audio-in 147
audio-out 148
external monitor 148
HDMI 149
headphone 148
microphone 147
modem 150
monitor 148
network 150
RJ-11 150
RJ-45 150
Universal Serial Bus
(USB) 151
plastic parts 44
Plastics Kit
contents 30
spare part number 20, 30,
40
play/pause button 10
pointing device
components 12
product description 6
ports
1394 15
eSATA/USB 15
expansion port 3 15
external monitor 15
HDMI 15
monitor 15
product description 5
USB 14, 15
power button 9
power button board
removal 73
spare part number 19, 40,
73
power connector 14
power connector cable
illustrated 31
removal 96
power cord
set requirements 152
spare part numbers 34, 42
power light 13
power requirements, product
description 6
power-on password 107
previous/rewind button 10
processor
product description 1
removal 102
spare part numbers 20, 38,
39, 102
Processor C4 State 107
product description
audio 4
chipset 1
display panel 2
docking support 5
Ethernet 4
external media cards 5
graphics 2
hard drives 3
keyboard 6
memory module 2
microphone 4
modem 4
operating system 6
optical drives 3
pointing device 6
ports 5
power requirements 6
processors 1
product name 1
security 6
serviceability 6
TV tuner 5
webcam 4
wireless 4
product name 1
R
rear components 14
recovering a program or
driver 142
recovering from the dedicated
recovery partition 146
recovering from the recovery
discs 146
recovery 146
recovery discs 146
Recovery Manager 142
recovery partition 146
recovery, system 142
remote control, spare part
numbers 34, 37
removal/replacement
preliminaries 44
procedures 50
restore points 144
right-side components 14
RJ-11 jack
location 14
pin assignments 150
RJ-45 jack
location 15
pin assignments 150
RTC battery
removal 59
spare part number 22, 43,
59
Rubber Feet Kit, spare part
number 21, 40, 51
S
safeguarding information 142
Screw Kit
contents 126
spare part numbers 35, 40,
43
screw listing 126
secondary hard drive self
test 108
security cable slot 14
security, product description 6
service considerations 44
service tag 17, 50
serviceability, product
description 6
Setup Utility
changing the language 105
Diagnostics menu 108
display system
information 105
exiting 106
Main menu 107
menus 107
restoring default settings 106
Security menu 107
starting 104
System Configuration
memu 107
using 105
solid-state drive (SSD) 142
speaker assembly
removal 74
spare part number 19, 41,
74
speaker components 9
speakers, locations 9
specifications
Blu-ray Disc ROM Drive 113
computer 109
display 110, 111
DVD±RW and CD-RW Combo
Drive 114
hard drive 112
I/O addresses 119, 121
interrupts 116, 117, 118
memory map 123, 124, 125
optical drive 113, 114
system DMA 115
static-shielding materials 48
stop button 10
supported discs 143
switch cover
removal 69
spare part number 19, 41,
69
system board
removal 92
spare part numbers 20, 37,
92
system DMA 115
system failure or instability 142
system information 107
system memory map 123, 124,
125
system recovery 142
T
thermal material,
replacement 100, 101
tools required 44
top components 7
top cover
removal 84
spare part numbers 20, 40,
84
TouchPad components
left button 12
light 12
on/off button 12
right button 12
scroll zone 12
TouchPad 12
transporting guidelines 47
TV antenna jack 14
TV tuner external antenna cable,
spare part numbers 22, 38, 57
Index 163
TV tuner module
removal 57
spare part numbers 22, 38,
57
TV tuner module cable
illustrated 31
removal 94
TV tuner, product description 5
U
Universal Serial Bus (USB) port
location 14, 15
pin assignments 151
unknown password 49
USB board
removal 90
spare part number 20, 41,
90
using system restore points 144
V
vents 14, 16
Virtualization Technology 107
volume mute button 9
volume scroll zone 10
W
webcam
location 8
product description 4
webcam light 8
webcam/microphone module
illustrated 27, 28
removal 53, 54, 78
spare part numbers 27, 28,
39, 40, 53, 79
Windows applications key 11
Windows logo key 11
wireless antenna
illustrated 29
locations 7
spare part numbers 29
wireless button 10
wireless, product description 4
WLAN module
location 16
removal 65
spare part numbers 23, 35,
36, 37, 38, 41, 65
workstation guidelines 47
164 Index