Scientific Journal of Impact Factor(SJIF): 3.134
e-ISSN(O): 2348-4470
p-ISSN(P): 2348-6406
International Journal of Advance Engineering and Research
Development
Volume 1,Issue 1, December -2013
Paper Title
Subtitle as needed (paper subtitle)
12pt, Times new roman
Font size: 14pt,
Times new roman,
Bold
First Author1, Second Author2, Third Author3
10pt times new
roman, Italic
1
Department name, College, Email id
Department name, College, Email id
3
Department name, College, Email id
2
10pt, Times new
roman
Abstract —This electronic document is a “live” template. The various components of your paper [title, text, heads, etc.]
are already defined on the style sheet, as illustrated by the portions given in this document. (Abstract) [line spacing 1.0]
10pt times
new
roman,
bold,italic
Keywords-component; formatting; style; styling; insert (key words) (minimum 5 keyword require) [10pt, Times new
roman,Italic, line spacing 1.0]
10pt,
Times
new
roman,
Italic
I.
INTRODUCTION
All manuscripts must be in English. These guidelines include complete descriptions of the fonts, spacing, and
related information for producing your proceedings manuscripts. Please follow them and if you have any questions,
direct them to the production editor in charge of your proceedings at the editor.ijaerd@gmail.com
10pt,
Times
II.
FORMATTING YOUR PAPER
10pt times
new

Paper
Size
:Prepare
your
paper
in
full-size
format,
on
A4
size.
new
roman,

Layout:
Portrait
roman,
1.0 Line

Line
spacing
:
1.0
Bold,
spacing

Margins
Top
=
18mm
(0.75”),
bottom
=
25mm
(1”),
side
=
18mm
(0.75”).
Uppercase
 Pagination. Number each page 17.5mm (0.5”) at the bottom center in 10 pt. font. (Applies to both Word and
PDF)
 Columns One columns, fully justified.
 Font Times New Roman.
 Style Primary, first-level headings are centered, numbered with Roman numerals (I., II., III., etc.) Secondary
Headings are flush left, numbered with cap letters (A., B., etc.)
 Figure and table captions should be 10-point boldface and Italic times new roman
or a similar sans-serif font). Callouts should be 9-point non-boldface Helvetica. Initially capitalize only the first word of
each figure caption and table title. Figures and tables must be numbered separately. For example: “Figure 1. Database
contexts” , “Table 1. Input data”. Figure captions are to be centered below the figures. Table titles are to be centered
above the tables.
III. FIRST-ORDER HEADINGS
For example, “I. INTRODUCTION”, should be Times 10-point boldface, initially capitalized, flush left, with
one blank line before, and one blank line after. Use a period (“.”) after the heading number, not a colon.
3.1. Second-order headings
As in this heading, they should be Times 10-point boldface, initially capitalized, flush left, with one blank line before,
and one after.
3.1.1. Third-order headings.
Third-order headings, as in this paragraph, are discouraged. However, if you must use them, use 10-point Times,
boldface, initially capitalized, flush left, preceded by one blank line, followed by a period and your text on the same line.
IV. FOOTNOTES
Use footnotes sparingly (or not at all) and place them at the bottom of the column on the page on which they are
referenced. Use Times 8-point type, single-spaced. To help your readers, avoid using footnotes altogether and include
necessary peripheral observations in the text (within parentheses, if you prefer, as in this sentence).
REFERENCES
The template will number citations consecutively within brackets [1]. The sentence punctuation follows the bracket [2].
Refer simply to the reference number, as in [3]—do not use “Ref. [3]” or “reference [3]” except at the beginning of a
sentence: “Reference [3] was the first . . .”
@IJAERD-2015, All rights Reserved
1
International Journal of Advance Engineering and Research Development (IJAERD)
Volume 1,Issue 1,December 2013, e-ISSN: 2348 - 4470 , print-ISSN:2348-6406
For papers published in translation journals, please give the English citation first, followed by the original foreignlanguage citation [6].
Format of Reference
[1] Author1, Author2, "Paper Title", Journal Name with Issue number, Page Number, Year
of
Publish
Example:
G. Eason, B. Noble, and I. N. Sneddon, “On certain integrals of Lipschitz-Hankel type involving products of Bessel
functions,” Phil. Trans. Roy. Soc. London, vol. A247, pp. 529–551, April 1955. (references)
[2] J. Clerk Maxwell, A Treatise on Electricity and Magnetism, 3rd ed., vol. 2. Oxford: Clarendon, 1892, pp.68–73.
[1]
@IJAERD-2014, All rights Reserved
2