Project Name
Project Location
Samet Job #
TRADE PACKAGE SCOPE OF WORK
01740 FINAL BUILDING CLEANING SUBCONTRACT
Furnish all labor, materials, tools, taxes, insurances, equipment, hoisting, cranes, supervision and all other
incidentals necessary to accomplish all Final Building Cleaning Work in accordance with all Contract
Documents as defined within Section 1700 Trade Package General Scope Requirements and this Scope of
Work.
Project Specifications for the Final Building Cleaning Scope of Work are listed below. This Subcontractor or
Supplier shall carefully examine all specification sections and drawings within the Contract Documents and be
responsible for all work described within this Scope of Work and as required on the project, except where
excluded or specifically assigned by the Scopes of Work to the other Subcontractors or Suppliers. This
Subcontractor or Supplier should carefully examine ALL SCOPE OF WORK PACKAGES for a clear
understanding of the delineation of work among Subcontractors and/or Suppliers.
PROJECT SPECIFICATIONS
01710 ........................................................................................................................................ Cleaning
08710 ................................................................................................. (Cleaning Only) Finish Hardware
08800 ............................................................................................................... (Cleaning Only) Glazing
09310 ............................................................................................................ (Cleaning Only) Hard Tile
09660 ...................................................................................................... (Cleaning Only) Resilient Tile
09680 .................................................................................................. (Cleaning Only) Carpet Flooring
09950 ............................................................................................ (Cleaning Only) Vinyl Wallcovering
The Final Building Cleaning Subcontractor shall be responsible for complying with the requirements of each
Scope of Work Description / Clarification Section listed below, even if those requirements are not shown
within the Specification Sections listed above.
17.0
SCOPE OF WORK CLARIFICATIONS AND/OR OTHER REQUIREMENTS
17.0.1 The Final Building Cleaning Subcontractor is responsible for all Work described herein and
below unless specifically noted otherwise to be part of another Subcontractor’s Scope of
Work.
17.0.2 Final Cleaning – Unless noted otherwise herein, the Work required as part of this Subcontract
shall include a comprehensive project cleaning, including but shall not be limited to the
following:
A. Sweeping and damp mopping of the following floor surfaces:
1.
2.
3.
4.
5.
6.
10.14.07
Sealed Concrete
Stained and/or Painted Concrete
Wood Flooring (Stage)
Hard Tile (Ceramic and Quarry Tile)
Resilient Tile or Sheet Vinyl Flooring
Other Miscellaneous Project Flooring
Trade Package - 01740 Final Building Cleaning, Page 1 of 4
This is a Portion of the Complete Trade Package of 4 Pages
Project Name
Project Location
Samet Job #
B. <As scheduled by Samet Corporation and prior to Owner move-in, sweep, damp mop and
strip the factory finish on resilient tile surfaces and then apply the specified neutralizing
floor cleaner and two (2) coats of wax per the resilient tile and wax manufacturer’s
recommendations to protect the resilient tile floor surfaces during and after construction.>
C. Vacuuming carpet (shampoo carpet, where necessary, to remove stains, etc.):
D. Wiping down and cleaning of the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
10.14.07
Plumbing fixtures and accessories
Manufactured casework and cabinets (interior and exterior)
Mirrors
Interior and exterior door and window frames
Interior and exterior glass including all windows, curtain wall, storefront and hollow
metal framed glass
Wall partitions including base materials
Toilet partitions and accessories
Light fixture lenses
All railings
Polished surfaces (i.e. elevator equipment, etc.)
Lockers
Removing manufacturer decals from equipment, etc.
Remove labels which are not permanent
Wood doors, fiber reinforced polyester doors and hollow metal doors
Rubber floor base
Aluminum curtain wall framing, glass, mullions, sills, headers, etc.
Aluminum storefront doors, glass and framing
Aluminum and/or Steel Sash window framing and glass
Millwork, counter tops, shelving, display cases, display case glass, etc. (interior and
exterior)
TV brackets
HVAC ceiling diffusers
Water heaters and equipment within janitor closets
Kitchen and Dish room equipment
All exposed horizontal ledges or flat surfaces that may retain debris, dirt, dust, etc.
All polished metal/finish metal surfaces, including but not limited to, electrical
device cover plates, door hardware, stainless steel corner guards, walk –in
cooler/freezers, etc.
Roll up coiling doors and grilles
All polished metal/finish metal surfaces, including but not limited to, electrical
device cover plates, door hardware including hinges, stainless steel corner guards,
walk–in cooler/freezers, etc.
Fiberglass shower stalls
All hard tiled and/or glazed block wall surfaces
Visual display boards & trays (remove protective coverings, stickers & clean
surfaces)
Residential appliances (inside and out)
Elevators (all exposed finish surfaces)
Stairwell framing assemblies
Trade Package - 01740 Final Building Cleaning, Page 2 of 4
This is a Portion of the Complete Trade Package of 4 Pages
Project Name
Project Location
Samet Job #
34. Interior surfaces of can lights and bulbs
35. Clean exposed areas of exterior canopy.
36. Clean exposed exterior and interior hard-surfaced finishes to a dust-free condition, free of
stains, films, and similar foreign substances.
37. Restore reflective surfaces to their original reflective condition.
38. Wipe surfaces of plumbing, mechanical and electrical equipment. Remove excess lubrication
and other substances.
39. Vacuum carpet using commercial machine with face-beater element.
40. Exposed Mechanical Ductwork, piping, accessories and heaters are to be cleaned.
41. Pressure wash exterior sidewalks, concrete pavement, etc.
42. <Media Center furnishings>
E. <Pressure washing and cleaning of the exterior of the buildings. Extreme care shall be
taken when pressure washing the exterior of the buildings in order to prevent damage to
the existing building’s exterior.>
17.0.3 The Final Cleaning Subcontractor shall use only cleaning materials and equipment that are
compatible with the surface being cleaned, and as recommended by the manufacturer of the
material. Prior to the final building cleaning work commencing, the Final Building Cleaning
Subcontractor shall obtain the manufacturer’s recommended cleaning guidelines from the
applicable on-site Subcontractor or Samet Corporation to ensure cleaning materials used to
accomplish this Scope of Work will not harm or detrimentally affect the particular item or
surface being cleaned. The Final Building Cleaning Contractor will not claim lack of
knowledge of manufacturer product for any surfaces, if damaged from improper cleaning and
will reimburse Samet Corporation in full for any damaged surfaces. Final Cleaning
Contractor will not proceed with any cleaning until building component’s product data has
been read and acknowledged.
17.0.4 Employ experienced workers or professional cleaners for final cleaning. Clean each surface
or unit to the condition expected in a normal, commercial building cleaning and maintenance
program. Comply with all manufacturers’ instructions.
17.0.5 Final building cleaning Work will require multiple mobilizations as directed by Samet
Corporation. No additional charges will be accepted for multiple mobilizations.
17.0.6 Wash all glass on both faces in each area of Project not more than four (4) days prior to date
scheduled for inspections that establish date of Substantial Completion. Wash glass as
recommended by glass manufacturer. Glass sand Glazing is to be cleaned interior and
exterior on all levels and elevations of the project.
17.0.7 The Final Building Cleaning Subcontractor shall reference the Interior Finish Schedule
designated on the drawings in order to determine the floor and wall finishes which shall be
cleaned as part of this Scope of Work.
17.0.8 The Final Building Cleaning Subcontractor shall remove paint drippings, spots, stains, and
dirt from all finished surfaces scheduled to be cleaned as part of this Scope of Work.
17.0.9 Upon completing the final building cleaning work within a specific building area, the Final
Building Cleaning Subcontractor shall request Samet Corporation to inspect the particular
10.14.07
Trade Package - 01740 Final Building Cleaning, Page 3 of 4
This is a Portion of the Complete Trade Package of 4 Pages
Project Name
Project Location
Samet Job #
building area for approval. Following receipt of written approval from Samet Corporation,
the Final Building Cleaning Subcontractor shall not be obligated to re-clean the previously
cleaned and approved specific building area. <However, if requested to re-clean a particular
building area, then the Final Building Cleaning Subcontractor will be compensated using the
Quantitative and General Allowances to be included within the Final Building Cleaning
Subcontractor’s Base Bid amount as defined within Section 1210 – Allowances.>
17.0.10 The Final Building Cleaning Subcontractor shall make provisions within its Base Bid
proposal to include all necessary scaffolds, man lifts, etc. in order to reach areas within the
building(s) which will require final cleaning as part of this Subcontract. Where scaffolds,
man lifts, etc. are necessary, the Final Building Cleaning Subcontractor shall be responsible
for protecting the applicable floor and/or roof surface, etc. by providing an approved covering
(i.e. plywood, etc.) in order to prevent damage to the applicable floor and/or roof surface.
17.0.11 Prior to commencing with the installation of work scheduled to be applied on new
construction materials, the Final Cleaning Contractor shall field verify and provide Samet
Corporation with written confirmation that all substrate finishes are acceptable to receive the
specified Final Cleaning system provided as part of this Scope of Work. Failure to notify the
Samet Corporation in writing of such acceptance prior to commencing any work shall
constitute this Subcontractor’s acceptance of the applicable substrate finish.
17.0.12 Prior to commencing with the installation of work scheduled to be applied on existing
construction materials, the Final Cleaning Subcontractor shall field verify and provide all
necessary preparation work including pressure washing, sanding, scraping, cleaning, deglazing, etching, etc. as required to properly prepare the existing substrate finishes to receive
the specified Final Cleaning system provided as part of this Scope of Work.
17.0.13 The Final Cleaning Subcontractor shall be responsible for providing and maintaining
protective coverings, when required to protect the work of other trades. Should any Final
Cleaning damage or come into contact with work of other trades, then the Final Cleaning
Subcontractor shall be responsible for all costs necessary to restore the affected work back to
its original condition prior to the Final Cleaning being installed.
- SUMMARY INFORMATION A.
The Substantial Completion date for the Final Building Cleaning Subcontractor is as reflected
within the Construction Schedule. Special attention should be directed to the Construction
Schedule for project sequencing requirements which are a requirement of this Scope of Work.
END OF SECTION
TRADE PACKAGE SCOPE OF WORK:
01740 – FINAL BUILDING CLEANING SUBCONTRACT
10.14.07
Trade Package - 01740 Final Building Cleaning, Page 4 of 4
This is a Portion of the Complete Trade Package of 4 Pages