1 REVISION HISTORY ............................................................................................................................ 4 2 ABBREVIATIONS ................................................................................................................................. 5 3 OVERVIEW ........................................................................................................................................... 6 4 5 6 7 3.1 INTRODUCTION .............................................................................................................................................................. 6 3.2 THEORY OF OPERATION................................................................................................................................................ 6 3.3 SPECIFICATION ............................................................................................................................................................... 6 3.4 FEATURES AND BENEFITS .............................................................................................................................................. 7 DETECTION CHARACTERISTICS ........................................................................................................ 8 4.1 DETECTION REQUIREMENTS ......................................................................................................................................... 8 4.2 TYPICAL DETECTION PATTERNS ................................................................................................................................... 9 4.2.1 Microwave .............................................................................................................................................................. 9 4.2.2 Deadzone ................................................................................................................................................................ 9 SYSTEM COMPONENTS ................................................................................................................... 11 5.1 HARDWARE COMPONENTS ........................................................................................................................................11 5.2 SOFTWARE COMPONENTS ..........................................................................................................................................11 SYSTEM DESIGN ................................................................................................................................ 13 6.1 SITE PLANNING ............................................................................................................................................................13 6.2 FOLIAGE MANAGEMENT .............................................................................................................................................13 6.3 UNEVEN TERRAIN ........................................................................................................................................................13 6.4 RAIN, STANDING WATER AND FROST .......................................................................................................................13 INSTALLATION PROCEDURE ........................................................................................................... 14 7.1 POLE MOUNTING ........................................................................................................................................................14 7.2 ALIGNMENT ..................................................................................................................................................................14 7.3 HALO WIRING ............................................................................................................................................................15 7.4 HALO CONFIGURATION ............................................................................................................................................18 7.4.1 Installing the HALO Configuration Utility ................................................................................................18 7.4.2 Adding users to the OSDP Hub.....................................................................................................................18 7.4.3 Starting the HALO Configuration Utility ...................................................................................................19 7.4.4 Installing a HALO Device ................................................................................................................................20 7.4.5 Configuring a HALO Device ...........................................................................................................................23 7.4.6 HALO Configuration Utility Tabs .................................................................................................................28 7.4.7 Restore Factory Defaults .................................................................................................................................30 Revision History 8 VERIFICATION AND TEST ................................................................................................................ 31 9 MAINTENANCE ................................................................................................................................. 33 10 CERTIFICATE OF CONFORMITY .................................................................................................. 34 Installation Manual 3 HALO Revision History 1 Revision History Date Version Signed Comments 29/04/2014 1 Maria Heneghan Document Created 20/11/2014 1.1 Maria Heneghan Minor Updates 01/12/2014 1.4 Maria Heneghan Branding Change / Updated configuration Utility sections and images 06/01/2015 1.5 Maria Heneghan Minor updates / alarm classification section updated with error alarm information 02/03/2015 2.1 Maria Heneghan Updated 5.1 Hardware Components to reflect the hardware changes. 19/05/2015 2.2 Maria Heneghan Added Certificate of Conformity. Minor changes to Section 7.3 Halo Wiring 22/10/2015 2.3 Maria Heneghan 3.3 Changed temperature specification 7.4.4 Added Model Name information, changed Figure 18. 7.4.5 Added Figure 19 and Figure 20. Added Range and Algorithm information. Added Deadzone sensitivity settings. Text updated regarding configuration. Table 1: Revision History Installation Manual 4 HALO Abbreviations 2 Abbreviations CP Control Panel DSP Digital Signal Processing FSK Frequency Shift Keying OSDP Installation Manual Open Supervised Device Protocol PDs Peripheral Devices PIDS Perimeter Intrusion Detection System POE Power Of Ethernet RSSI Received Signal Strength Indicator RX Receiver SCS Secure Channel Session TX Transmitter 5 HALO Overview 3 Overview 3.1 Introduction HALO is a bistatic radar, Perimeter Intrusion Detection System (PIDS). The system is comprised of HALO Transmitter (TX) and HALO Receiver (RX) pairs. The HALO is a platform based system which operates at distances ranging from 3 – 100M. The HALO has both RS485 and Ethernet connectivity for configuration and integration. Each HALO is software configurable as a TX or RX unit. HALO brackets (part code HALO-BRK) are available for mounting a set of units to a pole of >40mm ø. Due to the unique design of the HALO, cross-hatching installation is not required. This reduces pole numbers 3.2 Theory of Operation The HALO system consists of pairs of TX’s and RX’s. The system detects the presence of objects moving through the detection zone created by each TX / RX pair. On detection of an object an alarm is generated which can activate any of the following: 3.3 1. Relay Closure / Open – user configurable 2. Alarm notification via RS485 3. Alarm notification via Ethernet Specification Parameter Value Frequency 5.785-5.815 GHz. Modulation Full-duplex bidirectional FSK Channels 30 + Range 3 – 100 m Probability of Detection 99% Temperature -40°C to 65°C. Humidity 0 – 95% Non – Condensing Power Requirements 12-48V / POE Current Consumption 450mA Housing IP65 rated Installation Manual 6 HALO Overview 3.4 Features and Benefits Two software configurable relays Four Analog Inputs Installation and Integration via RS485 or Ethernet Self-calibrating, adaptable DSP using 3 distinct signal paths Software Adjustable Sensitivity Dead Zone Elimination On-board secure IC enables Secure Authentication of TX/RX Pairs SD card backup 12 – 48V or POE powered Six distinct software activated alarm types: Environmental, Error, Tamper, Intruder, Power and Auxiliary Dead Zone Elimination sensitivity configuration Installation Manual 7 HALO Detection Characteristics 4 4.1 Detection Characteristics Detection Requirements The HALO will detect any object with a mass > 35Kg moving through the detection zone created by each TX/RX pair. Figure 1 depicts a side view of the detection zone of the HALO. Figure 1: HALO Detection Zone side view The HALO has eight software configurable sensitivity settings which make the HALO suitable for installations in multiple environments and locations. The height and width of the detection zone varies due to software configurable sensitivity level assigned to the RX. The sensitivity level effect on the beam width is depicted in Figure 21. 1 Figure 2 is not to scale. The beamwidths for each sensitivity level are exaggerated in order to demonstrate the effect. The data is based on a 100M link. Installation Manual 8 HALO Detection Characteristics Figure 2: Sensitivity Effect on Beam Width - Ariel View 4.2 4.2.1 Typical Detection Patterns Microwave Microwave bistatic radar links have a detection zone which is ellipsoid in shape, i.e. the detection zone is widest at the middle of the link and narrowest at either side of the link. The width of the detection zone of the HALO is no greater than 5m. 4.2.2 Deadzone Traditional Microwave systems have a ‘dead zone’ within which intruder movement may remain undetected by the system, as the forward scattered multipath signals generated by the movement of the intruder may be at a level lower than that which may be discerned from noise at the receiver. The dead zone is located (i) on the ground directly below and in front of their transmit/receive antennas, (ii) above the transmit/receive antennas, as shown in Figure 3. Figure 3 Bistatic radar detection zone side view – dead zone dimensions Installation Manual 9 HALO Detection Characteristics The deadzone length l in Figure 3 is < 4m with an HALO mounting height of 1.1m. The HALO is fitted with LOWER DEADZONE elimination modules which provides coverage of the “Lower Deadzone” area not covered by traditional microwave systems. UPPER DEADZONE elimination modules are also available. HALO with Upper Deadzone Elimination Modules (HALO-UDZ) can be purchased from Sensurity. Installation Manual 10 HALO System Components 5 System Components 5.1 Hardware Components The HALO TX and RX units are physically identical. They units are individually software configurable to operate in either TX or RX mode. Each HALO unit consist of the following components: 1. Antenna 2. Motherboard 3. Lower Dead Zone Elimination Assembly 4. Upper Dead Zone Elimination Assembly, (Not included as standard) 5. HALO Front Cover 6. HALO Rear Cover 7. Access Panel Cover 8. HALO Bracket (HALO-BRK). (Not included as standard) Figure 4: HALO Hardware Components 5.2 Software Components Sensurity provides a HALO configuration utility in order for users to install and configure HALO units. The executable installs the following components: Installation Manual 11 HALO System Components 1. HALO Configuration Utility - a UI for the user to configure a network of Peripheral Devises (PDs). 2. OSDP Hub - a communications application used to network a mixture of RS485 and TCP/IP PDs with a Control Panel application connected over TCP/IP. This application simply acts to relay data packets between the attached Control Panel and all PDs. Installation Manual 12 HALO System Design 6 System Design 6.1 Site Planning Ensuring the suitability of a site for installation of the HALO system is imperative. A site survey prior to install should be carried out to ensure that nodes are located in such a manner as to be most beneficial to the site. 6.2 Foliage Management It is recommended to keep foliage within the detection zone to a minimum. Foliage encroaching on the detection zone may result in false alarms due to movement caused by wind. It is not advised to have trees directly within the detection field as their movement due to wind may cause alarms. 6.3 Uneven Terrain The operation of a HALO link requires transmission of energy from the transmitter to the receiver it is therefore recommended that there is line of sight between the transmitter and receiver units. To ensure a clear line of sight between the units the ground must be flat across the detection zone. A slope is permissible however troughs or hills may shadow the beam and thus allow crawl spaces (dead zones) for an intruder. See Figure 5. The protected area can be made up of any surface such as tar, concrete, grass, tilled earth or gravel Figure 5: Uneven Terrain 6.4 Rain, Standing Water and Frost The HALO is unaffected by rain, frost and snow. Fast flowing water in the detection zone (such as streams etc.) may cause alarms and it is thus recommended that the detection zone be free from streams or large pools of water. Installation Manual 13 HALO Installation Procedure 7 7.1 Installation Procedure Pole Mounting The HALO should be mounted on a pole of diameter no less than 40mm. A mounting height of 1.1m is recommended. The mounting height given is relative to ground level, of the midpoint of each TX/RX enclosure. Figure 6: Halo Mounting 7.2 Alignment TX/RX enclosures for each link should be mounted at the same height and be facing each other with clear line of sight. The maximum offset of the devices should be no greater than 6° to ensure maximum operational capability. Installation Manual 14 HALO Installation Procedure Figure 7: HALO Mounting and Alignment 7.3 HALO Wiring Figure 8: Access Panel View 1. Remove the access panel from the back of the HALO. 2. Connect cable for installation and configuration: a. For installation and configuration of the HALO over RS485 connect an RS485 cable to RS485_12 and GND. Ensure Pin 3 on S1001 is set to the ON position. 2 If configuring over RS485 the device must be powered up via 12-48V DC Installation Manual 15 HALO Installation Procedure b. For installation and configuration of the HALO over Ethernet connect an Ethernet cable to J700. Ensure Pin 3 on S1001 is set to the OFF position. 3. Two Relays are available RLY1 and RLY2 on Terminal J701. See Table 4. a. It is possible to activate external devices (such as lights, beacons or speakers) from the relays. b. The 12V and 5V Outputs (Pin 4 & Pin 5 on J701), should not be used to power external devices. These outputs can be used as signal outputs only. c. For detailed relay operation see Section 7.4.5 Configuring a HALO Device. 4. LED1001 is a power indicator LED. Once powered this LED will illuminate. 5. LED1000 is a status indicator LED and alerts the user to the firmware status of the CPU. Once powered LED1000 will illuminate yellow during the boot process. Once firmware is booted it will flash on and off indicated that the firmware is loaded and the device is ready for use. 6. Once all cables have been connected attach the access panel cover using the screws provided. Ensure that the tamper sensor (U508 Figure 8) is not obstructed by cabling. U508 must have a clear view of the reflective material within the access panel cover to ensure tamper alarms will be activated on removal of the cover. Table 2: X700 Terminal Block Connections X700 Terminal Block PIN SYMBOL DESCRIPTION 1 PWR_IN POWER INPUT 2 485_PWR 3 GND Common Ground 4 GND Common Ground 5 GND Common Ground 6 GND Common Ground 7 GND Common Ground 8 GND Common Ground Table 3: X701 Terminal Block Connections X701 Terminal Block PIN SYMBOL DESCRIPTION 1 A1 Analog Input 1 2 A2 Analog Input 2 3 A3 Analog Input 3 4 A4 Analog Input 4 5 485-1_B+ RS485 INPUT 1 B+ Installation Manual 16 HALO Installation Procedure 6 485-1_A- RS485 INPUT 1 A- 7 485-2_B- RS485 INPUT 2 B+ 8 485-2_B+ RS485 INPUT 2 A- Table 4: J701 Terminal Block Connections J701 Terminal Block PIN SYMBOL DESCRIPTION 1 NC2 Relay 2 Normally Closed 2 COM2 Relay 2 Common 3 NO2 Relay 2 Normally Open 4 12V 12V 5 5V 5V 6 NC1 Relay 1 Normally Closed 7 COM1 Relay 1 Common 8 NO1 Relay 1 Normally Open Table 5: Switch S1001 Switch Description 1 Program Select 2 Program Select 3 Communication configuration Method Selection 4 Parameter Reset at Power on Table 6: LED Indicators LED Function LED1000 Power Indicator GREEN LED1001 Status Indicator ORANGE Installation Manual 17 HALO Installation Procedure 7.4 HALO Configuration 7.4.1 Installing the HALO Configuration Utility Download and install the latest version of the HALO control panel: halo_cp-installer.exe Double click on the installer to start installation The Microsoft Visual C++ redistributable is required to run the configuration utility. If not already installed the HALO executable will install it. If the PC has the redistributable previously installed the dialog box in Figure 9 will appear. Click on close to continue with the configuration utility installation. Figure 9: Microsoft Visual C++ Redistributable Installed Dialog Box If the Microsoft Visual C++ redistributable has not been previously installed on the PC the dialog box in Figure 10 will appear. The user must agree to the license terms and conditions and install the redistributable in order to install the HALO Configuration Figure 10: Microsoft Visual C++ Redistributable Install Dialog Box 7.4.2 Utility. Adding users to the OSDP Hub The OSDP Hub allows multiple users to be supported in connections from a Control Panel (CP) on the Master TCP/IP port. Access to this port requires access using a username and password. The Secure Remote Password (SRP) protocol (a patent free IETF standard) is used to store username/password credentials on the OSDP Hub server machine and to perform a 2-way handshake initiated by the CP (client). The software installer will automatically configure the following default username and password: Username: admin Password: 1234 Installation Manual 18 HALO Installation Procedure 7.4.3 Starting the HALO Configuration Utility NOTE: When installing the HALO over IP the computer the HALO hub utility is running on should be set to static IP address 192.168.2.10. Run the utility Start -> All Programs -> Sensurity -> HALO Control Panel The user will be prompted for a password. This password is used to encrypt the OSDP master key stored in the osdp_map.xml. See Figure 11. If running the CP for the first time insert the default password 1234. Figure 11: Enter Password Prompt Following the login process the user will then be presented with the User Interface (UI) Status Page in Figure 12. To connect to a network, the user should select the Connect button in the top left corner of the UI. Figure 12: Halo Configuration Utility UI The user will then be prompted to enter the IP address and port of the OSDP Hub executable. The default IP address is localhost (i.e. 127.0.0.1) meaning that the OSDP Hub is running on the local machine. See Figure 13. If OSDP Hub is running on another computer the UI can connect to it using that computer's IP address. The default port of 27043 should only be changed it the default master port on OSDP Hub has been changed. Installation Manual 19 HALO Installation Procedure The username and password is required to authenticate the connection to the hub. The details should be inserted in the dialog box in Figure 13. If the user is logging in for the first time – the default username and password should be used. Username: admin Password: 1234 Figure 13: Connection Authentication 7.4.4 Installing a HALO Device If the device is connecting to the CP for the first time then it must be installed. To install the device click on File -> Install Device. See Figure 14. Figure 14: Install Device Installation Manual 20 HALO Installation Procedure If an uninstalled device is found the Install dialog box will be displayed – See Figure 153. Choose an OSDP address for the device (0-126) and click OK. Once a device is connected and installed it will be displayed on the configuration panel with the list columns indicating the status, OSDP address and connection status of each device. Figure 15: Install Dialog Box Each device on the network must be assigned a unique OSDP address ranging from 0-126. The HALO Configuration Utility consists of two main panels. On the left hand panel the installed devices are displayed. The right hand panels displays status and other information relating to each device. To see the status of a device the user must click and select the device from the left hand panel see Figure 16. The user can then navigate through the tabs in the right hand panel to view information pertaining to the device selected in the left hand panel. The status tab displays information on the device such as its serial number, the operating mode, IP settings and information on the current alarm status of the device. Also available on the status tab is the ability to disable the link for 30 seconds. This function allows the user to disable the link without the need to switch off the power supply. Click on the access control icon to disable the link for a duration of 30 seconds. Device IP settings can be set by the user on the status tab. NOTE: Ensure the correct model is indicated in Model Name See Figure 16. NOTE: Following power up communication with the device is available after 30s. The duration during which a device can be installed is fixed at 120s following the initial 30s start up procedure. Once the install duration has passed device will not allow a user to install. The timeout period can be altered by changing the Secure Channel Session timeout Period in the Admin Tab. See Figure 17. 3 Installation Manual 21 HALO Installation Procedure Figure 16: HALO Configuration Utility Device Status The HALO is a software upgradable device. The Admin Tab in Figure 17 allows the user to upgrade the software, reset the device and change the OSDP Secure Channel Session Timeout Period. NOTE: Upgrading firmware should only be performed if advised by your Sensurity representative. To reset the device click on the Soft Reset button. The CP renegotiates a new Secure Channel Session between the CP and the PD. The timeout duration can be changed by the user by altering the value in the Secure Channel Session timeout Period textbox and clicking on Configure. The duration is given in minutes. The minimum timeout period is 30 minutes and the maximum 1440 (24 hours). Installation Manual 22 HALO Installation Procedure Figure 17: HALO Configuration Utility Admin 7.4.5 Configuring a HALO Device To configure a HALO device select it from the status panel on the left. The selected device will be highlighted in blue. See Figure 18. Figure 18: Configuration Panel Settings Click on the settings tab and change the device settings as required and click Apply to save new settings. Installation Manual 23 HALO Installation Procedure To ensure the new settings have been applied click on the Refresh button. Ensure the device is highlighted in blue on the left hand panel to see the correct settings for the chosen device. Intruder Settings Operating Mode The signal settings – Bisatic Radar controls the settings for the microwave detection zone. Operating Mode has three options – Transmitter, Receiver or Bidirectional. Each device must be configured as either a Transmitter or Receiver. Bidirectional operation is not operational on these devices. For each pair of nodes there must be one device configured as a Transmitter with its paired node configured as a Receiver. Channel 37 channels are available. Any channel can be used for a pair of nodes. Each Transmitter and Receiver pair must be configured to operate on the same channel i.e. both devices configured for operation on channel 1. NOTE: configuring adjacent Node pairs with a channel separation of 11 is not advised as it may cause interference. Range The range function allows a number of range values to be chosen from a dropdown menu. If the range falls between two values use the larger value. For range above 100M set range to 100M. Algorithm The algorithm setting allows the user to choose which algorithm is best suited to their enviornment. Three algorithms are currently available to users. The algorithms and their best use case are described in this section. A drop down menu is available on the configuration utility to allow users to select the algorithm they wish to use see Error! Reference source not found.. Installation Manual 24 HALO Installation Procedure Figure 19: Configuration Utility Algorithm Settings Algorithm A This algorithm uses a digital sensing technique and offers “detect all” capability. Using this algorithm it is possible to configure the sensitivity to reject certain events such as small animals or parallel motion. Using Algorithm A on a high sensitivity level it is possible that certain foliage movements and small animals may result in an alarm event. This algorithm is suitable for those users who operate a sterile environment and wish to be alerted to EVERY event. Algorithm B Algorithm B is based upon extensive research and data analysis and is designed to offer the optimum rejection of fast moving objects such as small animals, thrown objects and birds. This algorithm works by extracting certain frequency components of the signal which are known to occur during deliberate intrusions but do not occur as a result of a fast moving small object. This algorithm offers the user the ability to detect all walking and running intruders while not raising an alarm when someone throws an object through the beam or when a bird flies through. This algorithm will also offer the user the ability to raise an alarm if a person is walking parallel to the link within the beam. This algorithm is best used in an environment where small animals result in false alarms. Algorithm C Algorithm C combines numerous digital signal analysis techniques to offer the highest degree of intelligence. Algorithm C offers the user the ability to raise an alarm due to a crawling, walking or running intrusion while not raising an alarm due to foliage movement, small animals or parallel motion. This algorithm is suited to environments where foliage encroaches on the detection zone. Installation Manual 25 HALO Installation Procedure Sensitivity The sensitivity of the device is software adjustable. As each 100M zone of a site may vary this allows the user to configure the system due to the unique conditions of the area. There are 8 sensitivity settings available for each algorithm A, B and C. For devices configured as a Transmitter this function does not change the operation of the device. For devices configured as a Receiver the sensitivity settings will change the operation of the device. Sensitivity 0 is the least sensitive setting and Sensitivity 7 is the most sensitive setting. Upper and Lower Deadzone Sensitivity The HALO device is optionally fitted with UPPER and LOWER deadzone elimation modules. If the device is fitted with upper or lower deadzone sensors ensure that the corresponding checkbox is ticked to ensure that deadzone detection is enabled and will trigger a relay if required. See Figure 20. The sensitivity setting of the deadzones can be altered using the configuration utility. Sensitivity 5 is the default and is appropriate for most installations on all surfaces. In some environments false alarms may occur and thus the sensitivity setting can be altered to counteract the false alarms. NOTE: In the event of reconfiguration of the deadzone sensitivity ensure that the area around the deadzone elimation module is kept clear for a period of 10s to ensure it recalibrates to its correct setting. Figure 20: Configuration Utility Deadzone Settings Installation Manual 26 HALO Installation Procedure Relay There are two software configurable relays on the HALO board. Each relay can be configured in 4 unique modes see Table 7. Table 7: Relay Modes Mode Description Disabled Relay is set to the NC position Normally OFF Relay is set to the NC position, in the event of an alarm the relay is set to the NO position for a defined duration Normally ON Relay is set to the NO position, in the event of an alarm the relay is set to the NC position for a defined duration Enabled Relay is set to the NO position Duration The relays remain in an alarm state for a number of seconds depending on the duration setting. This allows users the option to control the length of time a peripheral device is activated by triggering the relay for a user defined duration. The duration can be chosen by the user. The duration ranges from 1 second to 30 seconds in 1 second increments. Relay 1 and Relay 2 are independent and can be set to different durations. Alarms The HALO defines 5 different types of Alarm – Intruder, error, tamper, power and environmental. The checkbox for alarm type must be checked in order to ensure alarms of that type are transmitted. If the checkbox is not checked no alarms of that type are transmitted. If relay activation is required on alarm the corresponding checkbox must also be checked. To ensure that intruder alarms – microwave and deadzone - trigger an alarm the Intruder checkbox MUST be ticked. An Intruder alarm is activated if any of the following conditions are met: A microwave alarm, Upper deadzone alarm (if fitted and enabled) Lower deadzone alarm (if fitted and enabled). The Tamper alarm is activated if the access panel on the device is removed from the device. The alarm will trigger once and will not trigger again until the access panel is re-attached to the unit and removed Installation Manual 27 HALO Installation Procedure again. This prevents constant alarm triggering due to one event. Tamper alarms are only active if the Tamper checkbox is checked. Environmental alarms are caused by extreme temperature changes within the enclosure. The device is rated to operate at temperature range of - 30° to + 65°. If the temperature exceeds these values an Environmental alarm is triggered. An Environmental alarm will also be triggered if the temperature within the enclosure varies by ±10°C within an 8 minute period. Environmental alarms are only active if the Environmental checkbox is ticked. An Error alarm is generated if no SD card is present or has malfunctioned. The device will operate as normal however a number of features will be unavailable as listed below. Configuration settings backup Alarm history log Firmware upgrade An error alarm is also caused if the device suffers an unexpected event and needs to reboot. Following reboot the user will be notified via an error alarm. Power alarms are generated following device reconnection following a power outage. Analog input Settings There are 4 analog inputs available on the device. They are available on connector X701 see Table 3 for location and wiring details. External devices can be connected to any of the 4 analog inputs. The inputs are tolerant up to 12V. If a TTL High (>2.2V) is registered at the analog input A0 – A4 (See Table 3) for a duration of 1 second an alarm condition will be determined. To activate an Analog Input the corresponding checkbox must be enabled in the UI under the admin tab. Over-voltage protection is on the device for voltages > 13V. 7.4.6 HALO Configuration Utility Tabs Status See Section 7.4.4 Installing a HALO Device Admin See Section 7.4.4 Installing a HALO Device Settings See Section 7.4.5 Configuring a HALO Device. Graphs Installation Manual 28 HALO Installation Procedure The Graphs tab depicts one of the RSSI signal paths. This graph can be used to determine if the TX/RX pair is functioning correctly. The RSSI (counts) should be approximately 2000 counts and will vary considerably on a walkthrough event as depicted in Figure 21. To view the live Bistatic Radar graph the Enable checkbox must be checked and the receiver unit selected. Figure 21: Configuration Utility Graphs Test The test Tab is used primarily as an internal Sensurity utility. It can be used as a diagnostics tool to determine system performance. Installation Manual 29 HALO Installation Procedure Figure 22: Configuration Utility Test Trace The trace tab is used primarily as an internal Sensurity diagnostics tool. Figure 23: Configuration Utility Trace 7.4.7 Restore Factory Defaults The HALO can be reset to factory settings at any time using PIN 4 on S1001 (See Table 5). Pin 4 should be set to the ON position prior to power up to restore device factory defaults. Once powered up ensure that PIN 4 is switched to the OFF position to ensure that factory defaults are not restored on each subsequent power cycle. Installation Manual 30 HALO Verification and Test 8 Verification and Test To verify and test the installed TX/RX pairs, it is advisable to conduct false alarm testing and a number of penetration tests. It is advised to leave the units to “stabilize” and monitor for any false alarms for a minimum period of 10 minutes. Following switch on of the units it is recommended that no movable objects are present between the TX/RX pairs as this will interfere with initial system self-calibration. The detection zone should mimic the “real environment” free from intruders during the initial system self-calibration. This process should take no more than 1 minute. If false alarms do occur during this period there are number of possible causes. A possible cause in the absence of an actual intrusion or, conversely, the generation of no alarm in the event of an actual intrusion may be crosstalk from a nearby TX node. Below are a number of checks in order to diagnose the problem. Confirm the type of alarm generated: 1. If the alarm was of type Intruder, Perform checks a, b and c. If the alarm is not of type Intruder proceed to 2. a. Ensure that the TX/RX pair is configured correctly i.e. check that the paired devices are configured as 1 Tx and 1 Rx. b. Check that adjacent TX/RX pairs are not on the same channel or have a channel separation of 11. c. Ensure that the area is free from movement. 2. If alarm is of type Tamper ensure that the access panel is securely fastened. Reset the alarm. 3. If alarm is of type Environmental confirm that temperature is not exceeding Spec +65°C/-30°C or that a rapid changing in temperature has not occurred. It is recommended to perform a number of Penetration tests at varying distances along each link. See Table 8 as a guide. Table 8: Penetration Tests 1M 25M 50M 75M 99M If Lower deadzone enabled From the RX device From the RX device From the RX device If Lower deadzone enabled (crawl test) Installation Manual (crawl test) 31 HALO Verification and Test If any of the penetration tests do not result in an alarm the following checks should be performed: 1. Ensure that the Intruder checkbox is ticked in the admin tab of the control panel 2. If checking alarms using relays ensure that the relays are configured as Normally ON or Normally OFF) and that they are wired correctly. 3. If a 1M or 99M crawl test does not result in an alarm ensure that: a. The Lower Deadzone Elimination module is fitted in the device, and enabled Installation Manual 32 HALO Maintenance 9 Maintenance The HALO is designed for outdoor use and thus is subject to a constantly changing environment. To ensure the continued proper functionality it is important to maintain the area surrounding the system. Maintain natural features (grass, bushes, tree branches, etc.) within and at the edge of the detection zone. Following severe weather (storms, strong winds etc.) Ensure that no objects have entered the detection zone which may result in false alarms. Also ensure that the position of nodes has not changed due to the severe weather which may result in reduced system function due to improper alignment etc. Ensure that all alarms of type Environment are investigated as this alarm type is indicative of a system fault due to extreme temperature changes and may result in reduced system function Neglect of maintenance could jeopardize the continued proper functioning of the system. Installation Manual 33 HALO Certificate of Conformity 10 Certificate of Conformity Installation Manual 34 HALO