1 Scope of delivery
Siemens Industrial Turbomachinery AB offers design, manufacture,
packaging and shipment of the following equipment listed in the scope of
delivery:
The gas turbine generator set SGT-100 is designed for indoor installation,
consisting of:
1.1 Driven unit
1.1.1 Generator
· Brushless salient pole alternator 10.5 kV, 3-phase, 4-pole, 50 Hz, power
factor 0.8 · With ventilation with filtered air (together with the ventilation
system cover)
· Class H insulation and overall temperature class F
· Degree of protection of the generator cover - IP21
· Bearing Temperature Sensors generator
· Proximity sensor bearing vibration generator
· Pipelines lubricating oil - from the turbine to the generator
1.2 unit of the gas turbine
1.2.1 A gas turbine engine
Engine - a single-shaft, rated power of 5.4 MW (e).
· The gas generator
· Housing intake
· The compressor rotor
· Stator compressor with adjustable guide vanes
· Low-emission combustion system with dry low emissions (DLE)
· Turbine rotor
· Turbine stator
· The exhaust outlet
· Bearing Temperature Sensors Engine
· The engine has a layout with a drive to the cold end
1.2.2 The base frame
The base frame is a structure made of carbon steel multipoint bearing
equipment installed on it
· Mounting assemblies for mounting a gas turbine engine, auxiliary units and
an AC generator
· Built lubricating oil tank made of carbon steel
1.2.3 Start-up system
· Hydraulic and pump driven by an AC motor
1.2.4 gearboxes, couplings and guards
· The main reduction gear - planetary, output speed of 1500 rev / min.
· Test (seismic type) vibration reducer - Bently Nevada 1701
· The clutch actuator load with flexible dry-type elements
· Coupling guard (carbon steel)
1.2.5 System of lubricating oil
· The lubrication system of the gas turbine is used mineral oil
· The lubrication system is used for the turbine, gearbox and driven machine
· The main oil pump - driven turbine gearbox
· The auxiliary oil pump is driven by an AC motor
- Emergency oil pump driven by a DC motor.
· Filter lube oil system, double, carbon steel housing.
· Measuring converters module lubricating oil - standard intelligent
converters Siemens - aluminum housing
· Immersion heaters in the oil tank
· Prompter lube oil system
· Trap oil mist lubrication oil breather
· Pipeline venting is made of austenitic stainless steel.
· Air oil cooler
· Filter the air cooling of the lubricating oil
· Cooling fan - one at 100% load.
Suitable for the safe zone.
1.2.6 Fuel Gas
· System flow control starting fuel-driven
· The system controlling the flow of the main fuel-driven
· High-speed fuel shut-off valves (2 pcs.)
· Standard smart meters, pressure transducers production Siemens,
aluminum housing
· Satellite heating fuel pipeline to the frame GTU
· Thermocouples satellite system heating
· A fuel shut-off gas-venting valve assembly - outside of the module GTP,
satellite heating and insulation
1.2.7 The system of liquid fuel (optional)
· The pump liquid fuel drive - AC motor for zone 2
· Fuel filter for high pressure
· Adjusting the fuel supply valve
· System purging liquid fuel
· Heat discharge valve
· Pressure sensors, standard Siemens, aluminum
· Shut-off valve - standard Siemens - is the unit
1.2.8 noise insulation (KShT)
Noise insulation of painted carbon steel, closing the turbine, generator and
auxiliaries
· Doors to access attendants
· Built-in lifting member for service
· Interior lighting
· Standard intelligent sensors noise production Siemens, aluminum housing
1.2.9 The ventilation system noise insulation
· Air conditioning filters - pulse, automatic, self-cleaning, vertical - carbon
steel.
· Air conditioning filters, made in a single assembly with filters of cyclic air.
· The dampers with pneumatic actuator of the supply and air exhaust
ventilation system
· Fan - one - driven by AC motor - Zone 2
· The ventilation system - direct-flow, negative pressure
· Silencer ventilation systems - carbon steel
· Supporting apparatus for ventilation systems
1.2.10 Gas Detection System
· Equipment Gas Detection System consisting of: · 2 gas detector (at the outlet of the ventilation system)
1.2.11 Fire Protection System
Equipment fire protection system consisting of: · IR detectors / flame detectors x 3 pcs.
· Heat Detectors x 2 pcs.
· Siren x 2 pcs.
· Status indicator (at the end of the module) x 3 pcs.
· A manual call point (Manual Alarm Contact) x 3 pcs.
1.2.12 System extinguishing
· System of the carbon dioxide fire-extinguishing (CO2), two response
· Cylindrical tanks installed in an open rack on the base near the generator
· Pipe and nozzle extinguishing system
· Pipelines from the cabinet to the GTU
1.2.13 System cyclic air supply
· Pulse cyclic air filter (self-cleaning) - Carbon steel galvanized
· Cyclic air filter is made in a single assembly with filter ventilation
· Silencer system cyclic air - carbon steel galvanized
· Electric heating cyclic temperature is below -40 ° C
1.2.14 Exhaust System
· Exhaust diffuser - ferritic stainless steel
· Insulation and cladding of aluminum - to protect personnel
1.2.15 Electrical Systems module
· Motor Control Center - located outside of the module. Designed for motor
control, supplied Siemens, to be installed in the module
· The battery pack with charger, designed for the safe shutdown of the turbine
in an emergency
1.2.16 Auxiliaries Module GTU
· System Cold wash turbocharger - tank outside the frame GTU
· Drain tank module auxiliary
· Standard intelligent sensors Siemens parameters of auxiliary equipment,
aluminum housing
· Marking Instrument - An arrow mark - in accordance with the standard
flow diagrams (P & ID) Siemens
· Finishes Siemens standards for outdoor equipment
1.3 The control system
1.3.1 Hardware Management System
· Simplex control system power unit combined with Siemens PLC platform
· For monitoring and control systems for the module
· The control system placed on the module
· Built-in climate control
· Display of the operator, in Russian.
· Controls vibration and axial thrust - the system Bently Nevada 1701 system.
· The remote PC control and monitoring, monitor, keyboard and "mouse"
· Control Panel generator (design for the safe zone), includes: · Automatic Voltage Regulator
· Locking device - automatic and manual span with synchronizer
· Test Equipment generator and electrical protection
1.3.2 Siemens Turbomachinery Applications - Remote Monitoring System
STA -RMSTM
· Tools for data collection and exchange of information with objects outside of
the area, providing access to the following: · Exchange data via a broadband Internet connection (provided by the
customer)
· Automatic data logging within the boundaries of the control system
· Analysis of events
· Analysis of downtime
· Projected trends
· Detection of abnormal situations
· Software Update
· Support for the accelerated troubleshooting · Reports notification to the
Customer
· Access to archived data
· Review the performance of the park units and power units
· Monitor the status of the driven equipment
1.4 Test
1.4.1 Test gas turbine
· Test frames and systems of gas turbine
· Testing of the gas turbine engine - standard Siemens
1.4.2 Test of the driven equipment
· Standard factory acceptance test Alternator manufacturer
1.5 Installation and Maintenance
1.5.1 Installation and commissioning
· Shefnadzor for installation and commissioning (including verification of
performance station) will be the subject of another contract between the
Customer and the Supplier or its affiliate (available as an option).
1.5.2 Equipment for installation and maintenance
· Equipment for the rollout of the gas turbine
· Trolley for roll-out - the dismantling of the gas generator turbine engine
· Installation Tools
· Fixing components - gas turbine unit and driven machine
· Fixing components - for equipment installed outside of the module
· Choice of colors for on-site repair
· Drawings and Documentation
· Standard package of certified documents and approved drawings in English
· Operator's Manual, in English, is available on CD
· Maintenance Manual - in English, on CD
· Guide to the driven equipment, in English, on CD
1.6 Packaging and Shipping
1.6.1 Packaging
· The packing and preservation in accordance with the terms of destination
and, depending on the mode of transportation
1.6.2 Terms of delivery
· Delivery on DDP Moscow from the site in Lincoln, in accordance with the
terms of ICC INCOTERMS 2010
1.7 education
· 1 course management and maintenance for a period of 5 days to 10 (the
maximum possible amount) of participants.
1.8 Spare parts
1.8.1 Equipment and tools for commissioning
· Equipment and tools for commissioning
1.8.2 Spare parts for commissioning
· Spare parts for commissioning
1.9 Quality Assurance
· The quality assurance program under the contract - in English
· GOST certification
· Datasheet
· RTN Permit to Use
1.10 Options budget proposal
Option 1: The module of the liquid fuel (for changing the configuration of two
turbines on the fuel).
Option 2: Operational spare parts for 2 years operation
Option 3: The course (in Lincoln, United Kingdom)
2 Exceptions
· All items that are not listed in the proposal
3 The list price budget proposal
Set a single-shaft industrial gas turbine plant SGT-100 (1 pcs.), For indoor
installation, complete according to Section 1 - Scope of supply.
Total price including:
Module liquid fuel
Operational spare parts for 2 years operation