Second Quarter
Test (Week 3 and 4)
T.L.E- ICT 7
2nd Summative
Direction: Read each item carefully. Write only the LETTER of the correct answer in a sheet
of paper (½ lengthwise).
1. It is used to tighten / loosen cross head screw
a. Antistatic Wrist Strap
c. Hex driver
d. Flat Head Screwdriver
b. Philips Head Screwdriver
2. Which tool is used to retrieve parts from the location that are too small for your hand
to fit?
a. Part Retriever
c. Cable ties
b. Lint-free Cloth
d. Flat head screwdriver
3. What should always be worn when using hand tools?
a. Jewelries
b. Loose Clothes
c. Dangling Objects
d. Appropriate personal protective equipment such as safety goggles and
gloves
4. Which tool is used to test the integrity of circuits and the quality of electricity in
computer components?
a. Multitester
c. Philips head screwdriver
b. LAN Tester
d. Loop back Adapter
5. Which tool is used to strip and cut wires?
a. Part Retriever
c. Cable ties
b. Wire cutter
d. Flat head screwdriver
6. Which tool is used to loosen or tighten screws that have a star-like depression on
the top, a feature that is mainly found on laptop?
a. Torx screwdriver
c. Compressed air
b. Hex driver
d. Wire cutter
7. This is safety reminder “prevention is better than ________”.
a. Accident
c. Electric shock
b. Cure
d. Nothing
8. If you used a damaged hand tool, what will you do?
a. Tag a tool
c. Put in a trash can
b. Don’t use it
d. None of the above
9. As part of the normal operating and safety procedure, these tools should be
returned to the __________ after used.
a. classroom
c. store
b. laboratory
d. tool box
10. Which is likely to happen if you incorrectly used a defective tool?
a. Hand tools are extensions of our hands. When we misuse our hands, we
experience pain.
b. When we misuse hand tools, the possibility of injury to ourselves or people working
around us increases considerably.
c. using a tool incorrectly can damage the tool or even cause the tool to fail.
d. All of the above.
11. When sharpening hand tools, follow normal _____ procedure.
a. friendly
c. safety
b. common
d. sanitary
12. Which of the following is NOT part of the Basic Rules for Hand & Power Tools
a. Keep all hand tools in good condition with routine maintenance.
b. Use all the tools and within its intended purpose of design.
c. Use the damaged tools.
d. Operate tools within the manufacturer's guidance.
13. Which of the following would you do if the hinge screw door loosened?
a. Place a nailset in between the hinge plate and the hinge knuckle and hold.
b. Do not remove the hinge pin.
c. Immediately pull the door towards the closed position.
d. Do not replace the hinge pin.
FILL-IN THE BLANKS.
For item 14-16, read each statement carefully then fill-in the blanks with the correct
answer.
14. The purpose of an antistatic wrist strap is to ________ the electrical charge
between you and the equipment.
15. Turn the screwdriver ________________ to tighten the screw
16. Turn the screwdriver ________________ to loosen the screw.
TRUE OR FALSE.
For Item 17-20, read each statement carefully then write the letter of the correct answer.
17. Preparing for a task includes also the sequence of tasks to be done.
a. TRUE
b. FALSE
18. Preventive maintenance is the systematic care and protection of tools, equipment,
and machines in order to keep them in a safe, usable condition.
a. TRUE
b. FALSE
19. Properly stored tools and equipment will be easy to find when needed and are less
likely to be lost.
a. TRUE
b. FALSE
20. Use bins for storing small parts is a good practice on proper storage.
a. TRUE
b. FALSE