Uploaded by Glad Norman Limocon (OpenGx)

Grade7 Q1-4 W1 HandTools

advertisement
7
TLE - ICT-CSS
Quarter 1-– 4 Module 1:
Using and Maintaining Hand Tools
TLE ICT – Grade 8
Alternative Delivery Mode
Quarter 1 – Module 1: Using and Maintaining Hand Tools
First Edition, 2020
Republic Act 8293, section 176 states that: No copyright shall subsist in any work
of the Government of the Philippines. However, prior approval of the government
agency or office wherein the work is created shall be necessary for exploitation of such
work for profit. Such agency or office may, among other things, impose as a condition
the payment of royalties.
Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names,
trademarks, etc.) included in this module are owned by their respective copyright
holders. Every effort has been exerted to locate and seek permission to use these
materials from their respective copyright owners. The publisher and authors do not
represent nor claim ownership over them.
Published by the Department of Education
Secretary: Leonor Magtolis Briones
Undersecretary: Diosdado M. San Antonio
Development Team of the Module
Writer: Miraflor V. Banua
Editors: Jesusa D. Paladar, Mark Dave M. Vendiola
Reviewers: Jesusa D. Paladar, Mark Dave M. Vendiola and Jessie V. Alcala
Typesetter: Miraflor V. Banua
Management Team: Senen Priscillo P. Paulin, CESO V
Rosela R. Abiera
Marcelo K. Palispis, Ed.D.
Maricel S. Rasid
Joelyza M. Arcilla, Ed. D.
Elmar L. Cabrera
Nilita L. Ragay, Ed.D
Antonio B. Baguio Jr. Ed.D
Printed in the Philippines by ________________________
Department of Education –Region VII Schools Division of Negros Oriental
Office Address:
Tele #:
E-mail Address:
Kagawasan, Ave., Daro, Dumaguete City, Negros Oriental
(035) 225 2376 / 541 1117
negros.oriental@deped.gov.ph
8
TLE
Quarter 1-4 Module 1:
Using and Maintaining
Hand Tools
What I Need to Know
This module contains information and suggested learning activities on
Computer Hardware Servicing- Exploratory. It includes training materials and
activities for you to accomplish and complete.
You are required to go through a series of learning activities in order to
complete each of the learning outcomes of the module. Follow these activities
on your own and answer the given Task at the end of each learning activity.
The module is divided into three topics, namely;
Lesson 1
Prepare Hand tools
Lesson 2
Use Appropriate Hand Tools and Test Equipment
Lesson 3
Maintain Hand Tools
After going through this module, you are expected to:
1. Discuss the hardware tools used in computer hardware servicing
2. Identify the different types of hand tools used in computer hardware
servicing.
3. Value the importance of following safety precaution while working
1
What I Know
A. Choose your answer from the box below. Write your answer in your activity
notebook
Philips head screwdriver
Anti-static wrist strap
Compress air
Lan tester
Hex driver
Cables ties
Lint free cloth
Desoldering tool
flat head screwdriver
Multimeter
Paint brush
Crimping tool
Anti-static mat
Hand tools
Torx screwdriver
Wire cutter
__________1. A Tool used to strip and cut wires.
__________2. A tool used to unsoldered unwanted parts or component in the
circuit
with the support of soldering pencil.
__________3. This is use to loosen or tighten crosshead screws.
__________4. Sometimes called a nut driver, is used to tighten nuts in the same way
that a screwdriver tightens screws.
__________5. Its long and soft natural bristles can be used to dust off the surface of
circuit boards and its hard-to-reach areas
__________6. It is use to loosen or tighten slotted screws.
__________7. It is use to test the integrity of circuits and the quality of electricity in
computer components
__________8. It is use to clean different computer components without scratching or
leaving debris.
__________9. It is use to connect wires into the metal components of a computer; it is
designed to connect or attach a connector at the end of a cable to be
able to link or connect to a network of other computers
__________10. It is use to prevent ESD damage to computer equipment.
2
B. Matching Type
Match column B with the tools being describe in column A. Write the letter of the
correct answer in your notebook.
A
B
_______1. Use to stand on or place
hardware on to prevent static electricity
from building up.
A.
_______2. Tighten / loosen screw
B.
_______3. Tighten / looses bold with a
hexagonal head
C.
_______4. Retrieve parts that may be hard
to reach by your fingers
D.
_______5. a tool used to join two or more
metal conductors with the support of
soldering lead melted around it.
E.
Note: If you get 100% correct in this pre- assessment, skip the lesson but if
not and only get 50% to 99% correct, then proceed with the lesson.
3
Lesson
USING AND MAINTAINING
HAND TOOLS
1
What’s In
Why is it important to know the functions and uses of hand tools?
What do you observe when using hand tools?
What’s New
Arrange the scrambled letters to form a word below by
understanding the given meaning of the correct term. Write your answer in your
activity notebook.
TROLLEC-ITATSC SIDGEARCH LOOTS
____________________ Provides the most basic means for the controlled discharge of
electrostatic electricity.
DNAH TSOLO
____________________ Devices for performing work on a material or a physical system
using only hands.
NIEACLNG OOLTS
____________________ These tools ensure that computers stay tidy and dirt-free.
TINOGASDIC SOOLT
____________________ They are used to test the integrity of circuits and functionality
of ports.
4
What is It
Proper Tool Selection
A tool is a handheld device that aids in accomplishing a task.
Tools range from a traditional metal cutting part of a machine to an element of a
computer program that activates and controls a particular function.
Preparing for the task to be undertaken includes proper tool selection.
1.
How do you select the best tool for the job? First, know and understand
in detail the scope of work to be accomplished, second, plan for the scope taking into
account the sequence of tasks.
2.
Selecting the best tool for each task requires training in the proper use
of the tools, field experience in their safe use, and following the manufacturer’s
guidance and instructions for that specific tool.
3.
When obtaining the tool all the associated tooling and consumable
parts, as recommended by the manufacturer, must be included. In addition, related
consumable parts must also be selected and used according to their manufacturer’s
instructions.
Safe Use of tools
Once selected, use the tool for the purpose for which it was designed. Not all
tools come with detailed instructions, but there are those that do spell out the safety
―Do’s and Don’ts for your safety. If there are set-up/use options, operator judgment
must always be based on what is the safest way to use the tool.
Environmental Safety and Health Program requires the following:
Clean tools and equipment work more efficiently. At the end of
each working day clean the tools and equipment you used and
check them for any damage. If you note and damage, tag the
tool as faulty and organize a repair or replacement.
Electrical current can travel over oily or greasy surfaces. Keep
electrical power hand tools free from dust and dirt and make
sure they are free of oil and grease.
All workshop hand tools and equipment should have
maintenance schedule. Always complete the tasks described on
the schedule at the required time. This will help to keep the
hand tools in safe working order.
Store commonly used hand tools in an easy-to-reach location. If
a tool or a piece is too difficult to return, it could be left on a
5
workbench or on the floor where it will become a safety hazard. Keep your work
area tidy. This will help you work
more efficiently and safely.
HARDWARE TOOLS
To complete hardware repairs, it is important to have a toolkit that should contain
all of the necessary tools. As you gain experience, you will learn which tools to have
available for different types of jobs. Hardware tools are grouped into these four
categories:
•
•
•
•
Electro-Static Discharge (ESD) tools
Hand tools
Cleaning tools
Diagnostic tools
Electro-Static Discharge (ESD) Tools
Static electricity is easily generated by friction on carpets, tile flooring, clothing,
hair, fabric, and etc. The friction of moving air alone will charge suspended particles
and cause the buildup of static electrical charges on people and objects in the
environment. Grounded antistatic work mats used with antistatic wrist straps
provide the most basic means for the controlled discharge of electrostatic electricity.
Anti-static wrist strap – used to prevent ESD damage
to computer equipment.
Anti-static mat – used to stand on or place hardware
to prevent static electricity from building up.
on
Anti-static bag- is a packaging material that is specially
designed to help prevent static electricity interacting with
sensitive electrical components.
6
Hand Tools
A hand tool is a device for performing work on a material or a physical
system using only hands. The hand tools can be manually used employing force,
or electrically powered, using electrical current
Flat head screwdriver – used to loosen or tighten slotted
screws.
Philips head screwdriver – used to loosen or tighten
crosshead screws.
Torx screwdriver - used to loosen or tighten screws that
have a star-like depression on the top, a feature that is
mainly found on laptop.
Hex driver – sometimes called a nut driver, is used to
tighten nuts in the same way that a screwdriver tightens
screws.
Needle-nose plier – used to hold small parts
Wire cutter – used to strip and cut wires
7
Tweezers – used to manipulate small parts.
Flashlight or Headlight – used to light up areas that
cannot see well.
you
Soldering Pencil – a tool used to join two or more metal
conductors with the support of soldering lead melted
around it.
Desoldering Tool – a tool used to unsoldered unwanted
parts or component in the circuit with the support of
soldering pencil.
Precision
Screwdrivercomes
from
different
interchangeable heads which can be switched; used for
tiny screws found in the inner part of the components of
a compute
Crimping tool- used to connect wires into the metal
components of a computer; it is designed to connect or
attach a connector at the end of a cable to be able to link
or connect to a network of other computers
Cleaning Tools
Having the appropriate cleaning tools is essential when maintaining or
repairing computers. Using these tools ensures that computer components are not
damaged during cleaning. They also make computers tidy and dirt-free.
8
Lint-free cloth – used to clean different computer
components without scratching or leaving debris.
Compressed air – used to blow away dust and debris
from different computer parts without touching the
components.
Cable ties – used to bundle cables neatly inside and
outside of a computer.
Parts organizer – used to hold screw, jumpers, fasteners
and other small parts and prevents them from getting
mixed together.
Paint brush- its long and soft natural bristles can be used
to dust off the surface of circuit boards and its hardtoreach areas
Rubbing alcohol- used to wipe away sticky
substances on the surface of components; its quick
evaporation lessens the chance of causing electrical
damage to components
9
Diagnostic Tools
Computers are easier to use and more dependable with each new generation
of hardware and operating system update, but that doesn't mean they're problemfree.
Diagnostic tools are used to test the integrity of circuits and functionality of ports.
LAN Tester- is a device used to test the network connection.
Digital Multimeter- also called Volt-Ohm- Milliammeter
(VOM), a handy and battery operated tool used to measure
voltge, current and resistance; and effective tool to check
or diagnose if the circuits in a component is working or
not.
Multimeter – used to test the integrity of circuits and the
quality of electricity in computer components.
Loopback Adapter – used to test the functionality of
computer ports.
Toner probe – the toner part is connected to a cable at one
end using specific adapters, such as an RJ-45, coaxial, or
metal clips. The toner generates a tone that travels the length
of the cable. The probe part traces the cable. When the probe
is in near proximity to the cable to which the toner is
attached, the tone can be heard through a speaker in the
probe.
10
PROPER USE OF TOOLS
Proper Use of ESD Tools
The purpose of an antistatic wrist strap is to equalize the electrical charge
between you and the equipment. The antistatic wrist strap is a conductor that
connects your body to the equipment that you are working on. When static electricity
builds up in your body, the connection made by the wrist strap to the equipment, or
ground, channels the electricity through the wire that connects the strap. The wrist
strap has two parts and is easy to wear:
1. Wrap the strap around your wrist and secure it
using the snap or Velcro. The metal on the back of the
wrist strap must remain in contact with your skin at
all times.
2. Snap the connector at the end of the wire to the
wrist strap, and connect the other end either to the
equipment or to the same grounding point that the
antistatic mat is connected to. The metal skeleton of
the case is a good place to connect the wire. When
connecting the wire to equipment that you are working
on, choose an unpainted metal surface. A painted
surface does not conduct the electricity as well as unpainted metal.
An antistatic mat is slightly conductive. It works by drawing static electricity
away from a component and transferring it safely from equipment to a grounding
point: 1. Lay the mat on the workspace next to or under the computer case. 2. Clip
the mat to the case to provide a grounded surface on which you can place parts as
you remove them from the system. Reducing the potential for ESD reduces the
likelihood of damage to delicate circuits or components.
Proper Use of Hand Tools
A technician needs to be able to properly
use each tool in the toolkit. This topic covers
many of the various hand tools used when
repairing computers.
Screws Match each screw with the
proper screwdriver. Place the tip of the
screwdriver on the head of the screw. Turn
the screwdriver clockwise to tighten the screw
and counterclockwise to loosen the screw.
Screws can become stripped if you over-tighten them with a screwdriver. A
stripped screw, may get stuck in the screw hole, or it may not tighten firmly. Discard
stripped screws.
Flat head screwdriver Use a flat head screwdriver when you are working with
a slotted screw. Do not use a flat head screwdriver to remove a Phillips head screw.
11
Never use a screwdriver as a pry bar. If you cannot remove a component, check to
see if there is a clip or latch that is securing the component in place.
CAUTION: If excessive force is needed to remove or add a component, something is
probably wrong. Take a second look to make sure that you have not missed a screw
or a locking clip that is holding the component in place. Refer to the device manual
or diagram for additional information.
Phillips head screwdriver Use a Phillips head screwdriver with crosshead
screws. Do not use this type of screwdriver to puncture anything. This will damage
the head of the screwdriver.
Hex driver Use a hex driver to loosen and tighten bolts that have a hexagonal (sixsided) head. Hex bolts should not be over-tightened because the threads of the bolts
can be stripped. Do not use a hex driver that is too large for the bolt that you are
using.
CAUTION: Some tools are magnetized. When working around
electronic devices, be sure that the tools you are using have not
been magnetized. Magnetic fields can be harmful to data stored
on magnetic media. Test your tool by touching the tool with a
screw. If the screw is attracted to the tool, do not use the tool.
Part retriever, Needle-nose pliers, or tweezers The part retriever, needle-nose
pliers, and tweezers can be used to place and retrieve parts that may be hard to reach
with your fingers. Do not scratch or hit any components when using these tools.
CAUTION: Pencils should not be used inside the computer to change the setting of
switches or to pry off jumpers. The pencil lead can act as a conductor and may
damage the computer components.
Proper Use of Cleaning Materials
Keeping computers clean inside and out is
a vital part of a maintenance program. Dirt can
cause problems with the physical operation of
fans, buttons, and other mechanical components.
On electrical components, an excessive buildup
of dust will act like an insulator and trap the heat.
This insulation will impair the ability of heat
sinks and cooling fans to keep components cool,
causing chips and circuits to overheat and fail.
CAUTION: When compressed air is used to clean inside the computer, the air should
be blown around the components with a minimum distance of four inches from the
nozzle. The power supply and the fan should be cleaned from the back of the case.
CAUTION: Before cleaning any device, turn it off and unplug the device from the
power source.
12
Computer Cases and Monitors Clean computer cases and the outside of
monitors with a mild cleaning solution on a damp, lint-free cloth. Mix one drop of
dishwashing liquid with four ounces of water to create the cleaning solution. If any
water drips inside the case, allow enough time for the liquid to dry before powering
on the computer.
LCD Screens Do not use ammoniated glass cleaners or any other solution on
an LCD screen, unless the cleaner is specifically designed for the purpose. Harsh
chemicals will damage the coating on the screen. There is no glass protecting these
screens, so be gentle when cleaning them and do not press firmly on the screen.
CRT Screens to clean the screens of CRT monitors, dampen a soft, clean,
lintfree cloth with distilled water and wipe the screen from top to bottom. Then use
a soft, dry cloth to wipe the screen and remove any streaking after you have cleaned
the monitor.
Clean dusty components with a can of compressed air. Compressed air does
not cause electrostatic buildup on components. Make sure that you are in a
wellventilated area before blowing the dust out of the computer. A best practice is to
wear a dust mask to make sure that you do not breathe in the dust particles.
Blow out the dust using short bursts from the can. Never tip the can or use
the compressed air can upside down. Do not allow the fan blades to spin from the
force of the compressed air. Hold the fan in place. Fan motors can be ruined from
spinning when the motor is not turned on.
Component Contacts Clean the contacts on components with isopropyl
alcohol. Do not use rubbing alcohol. Rubbing alcohol contains impurities that can
damage contacts. Make sure that the contacts do not collect any lint from the cloth
or cotton swab. Blow any lint off the contacts with compressed air before
reinstallation.
Keyboard Clean a desktop keyboard
with compressed air or a small, hand-held
vacuum cleaner with a brush attachment.
CAUTION: Never use a standard vacuum
cleaner inside a computer case. The plastic
parts of the vacuum cleaner can build up
static
electricity and discharge to the components. Use only a vacuum approved for
electronic components.
Mouse Use glass cleaner and a soft cloth to clean the outside of the mouse.
Do not spray glass cleaner directly on the mouse. If cleaning a ball mouse, you can
remove the ball and clean it with glass cleaner and a soft cloth. Wipe the rollers clean
inside the mouse with the same cloth. Do not spray any liquids inside the mouse.
13
What’s More
Task 1.
Direction: Complete the table below. Choose at least 5 hand tools
available at home and conduct a maintenance activity.
TOOLS
MAINTENANCE ACTIVITY
Example:
1. Flat Head Screwdriver
Clean and Magnetize
What I Have Learned
Direction: Answer the K-W-L chart. Write your answer in your notebook.
K
W
L
What do you think you What do you WANT to What did you LEARN
KNOW about Hand
know about Hand
about Hand Tools?
Tools?
Tools?
What I Can Do
Activity 1
Direction: Identify the correct tool that is being described by the following
statements. After identifying the tool, classify it as ESD, Hand Tool , Cleaning Tool or
Diagnostic Tool. Write your answer in your activity notebook.
1. Used to strip and cut wires. (_______________, ______________)
2. Used to retrieve parts from location that are to small for your hand to fit.
(_______________, ______________)
14
3. Used to loosen or tighten slotted screws. (_______________, ______________)
4. Used to loosen or tighten screws that have a star-like depression on the top, a
feature that is mainly found on laptop. (_______________, ______________)
5. Used to blow away dust and debris from different computer parts without
touching the components. (_______________, ______________)
6. Used to light up areas that you cannot see well. (_______________, ______________)
7. Used to hold small parts. (_______________, ______________)
8. Used to test the integrity of circuits and the quality of electricity in computer
components. (_______________, ______________)
9. Used to clean different computer components without scratching or leaving
debris. (_______________, ______________)
10. Used to test the functionality of computer ports. (_______________, ______________)
11. Used to connect an RJ-45 to the end of a cable. (_______________, ______________)
12. Used to test LAN/Internet cable. (_______________, ______________)
Activity 2
Direction: Complete the computer cleaning chart shown below. Write your answer
in your activity notebook.
COMPUTER MAINTENANCE
COMPONENTS TO CLEAN
CLEAN WITH:
Computer case and outside monitor
Mild cleaning solution and lint free
cloth (sample)
Keyboard
Mouse
LCD Screen
CRT Screen
Heat Sink
RAM
Assessment
Fill in the blanks. Choose your answer from the box.
Write your answers in your activity notebook.
Hex driver
isopropyl
Four
insulator
counter clockwise Clockwise
distilled
Philips
equalize
15
lead
hand tools
safety
1. The purpose of an antistatic wrist strap is to ________ the electrical
charge between you and the equipment.
2. Turn the screwdriver _________ to tighten the screw
3. Turn the
screwdriver ________________ to loosen the screw.
4. Use a ________ head screwdriver with crosshead screws.
5. On electrical components, an excessive buildup of dust will act like an _________
and trap the heat.
6. When compressed air is used to clean inside the computer, the air should be blown
around the components with a minimum distance of ______ inches from the nozzle.
7. Pencils should not be used inside the computer to change the setting of switches
or to pry off jumpers because the tip contains _____ which can act as a conductor
and may damage the computer components.
8. To clean the screens of CRT monitors, dampen a soft, clean, lint-free cloth with
_______ water and wipe the screen from top to bottom.
9. Clean the contacts on components with _________ alcohol.
10.
Use a __________ to loosen and tighten bolts that have a hexagonal (six-sided)
head.
Multiple Choice
Select the letter of the correct answer. Write your answer in your activity notebook.
______ 1. What do you call this kind of ESD Tool that works by drawing static
electricity away from a component and transferring it safely from
equipment to a grounding point?
A. Anti-static wrist strap
C. Electro-Static Discharge (ESD)
Tools
B. Anti-static mat
D. Diagnostic tools
_____ 2. The following are the proper way of cleaning the component contacts
except____.
A. Clean the contacts on components with isopropyl alcohol.
B. Blow out the dust using short burst from the can.
C. Do not use rubbing alcohol.
D. Make sure that the contacts do not collect any lint from the cloth or
cotton swab.
______ 3. Which tool is used to manipulate small parts?
A. Wire cutter B. Tweezers
C. Part retriever
D. Hex driver
______ 4. Which tool is used to prevent ESD damage to computer equipment?
A. Anti-static wrist strap
C. Electro-Static Discharge (ESD)
Tools
B. Anti-static mat
D. Diagnostic tools
_____ 5. A Tool used to unsoldered unwanted parts or component in the circuit with
the support of soldering pencil
A. Desoldering Tool
C. Crimping Tool
B. Soldering Tool
D. part Retriever
______ 6. Which tool is used to test the integrity of circuits and the quality of
electricity in computer components?
A. Multimeter B. Tweezers C. Anti-static wrist strap DLoopback Adapter
______ 7. Which hand tool is used to driver to loosen and tighten bolts that have a
hexagonal (six-sided) head?
16
A. Needle-nose pliers C. Phillips head screwdriver
B. Tweezers
D. Hex driver
______ 8. Among the four categories of hardware tools, which tool is used for
performing work on a material or a physical system using only hands?
A. Hand Tool
B. ESD Tool
C. Cleaning Tool
D.
Diagnostic
Tool
_____ 9. Is a device used to test the network connection
A. LAN Tester
C. Loopback adapter
B. Multimeter
D. Crimping Tool
______ 10. Which cleaning tool is used to clean different computer components
without scratching or leaving debris?
A. Lint-free cloth
B. Cable ties C. Compressed air D.
Part
retriever
Additional Activities
Direction: Creating acrostic poem about Computer Hardware Tools.
Choose a particular tool to be the subject of your poem. Write the letters of
that word vertically on your paper. Now write about the subject using words
that start with the letters in your column. All lines of the poem should relate
to or describe the poem. Acrostic poems maybe made of single words, phrases
or sentences. The poem does not need to rhyme. Be creative and use your
imagination.
17
18
References
https://www.bing.com/images/search?view=detailV2&ccid=IYVNQlVF&id=A071E73B965F4EF6C518
286E5FAF01EE4CB88233&thid=OIP.IYVNQlVFM6kHxP1ffTk_OgAAAA&mediaurl=https%3a%2f%2fww
w.gamingscan.com%2fwp-content%2fuploads%2f2019%2f01%2fanti-static-wrist-strap-howtouse.jpg&exph=420&expw=420&q=anti+static+strap&simid=607997679151417319&ck=ACAA9C79
7C A3B29B5957C37185D05C3C&selectedIndex=69&ajaxhist=0
https://ndcllano.blogspot.com/2017/01/tools-for-computer-hardware-servicing.html
https://teachergelo.blogspot.com/2017/01/grade-7-lesson-2-use-of-tools-in-pc.html
http://ndcmartinez.blogspot.com/2017/01/1.html
http://www.deped.com/resources/9/k_to_12_pc_hardware_servicing_learning_module.pdf#:~:text
=Welcome%20to%20the%20world%20of%20Computer%20Hardware%20Servicing%21,like%20you%
20ought%20to%20possess%2C%20namely%3A%20%20.
https://www.bing.com/images/search?view=detailV2&ccid=xFr4Vt9V&id=A310899B876CBB518E58
927FFA4633A2CB00BF5C&thid=OIP.xFr4Vt9VlyHmt56Lsrh4pgHaE8&mediaurl=https%3a%2f%2fmarl
acummins.com%2fwp-content%2fuploads%2f2013%2f12%2fadhd-and-using-the-righttool.jpg&exph=352&expw=528&q=Proper+Tool+Use+Poster&simid=608028632932486907&ck=156
D3E4F72114FE4BE5B8DB61B1B1D2F&selectedIndex=64&ajaxhist=0
https://www.bing.com/images/search?view=detailV2&ccid=mwdTMVJb&id=11C3C19C1F088B9B42
8A5BBC2EF1732D441DF3C6&thid=OIP.mwdTMVJbh0kWMOZ7RUCd0gHaEw&mediaurl=https%3a%2
f%2ffthmb.tqn.com%2fjZpZAT8YKOjNKpYCj5uluMBKKVg%3d%2f3963x2549%2ffilters%3afill(auto%2
c 1)%2fscrewdriver-flat56a056d65f9b58eba4aff0cf.jpg&exph=2549&expw=3963&q=screwdriver&simid=608053801423471
332&ck=5CDBA3205F151E7D4245026812324CBA&selectedIndex=32&ajaxhist=0
https://www.bing.com/images/search?view=detailV2&ccid=H%2FXAax3F&id=C8895B70D0314C587
428BCB29D96F42592138AFA&thid=OIP.H_XAax3Ftu8OWIUBA9UiQHaHa&mediaurl=http%3A%2F%2Fi.ebayimg.com%2Fimages%2Fi%2F261549093889-01%2Fsl1000.jpg&exph=1000&expw=1000&q=screwdriver&simid=608011899829880832&ck=9C79B5C905E
21037827E0C5E9D6741CA&selectedindex=33&ajaxhist=0&vt=0&sim=11
https://www.bing.com/images/search?view=detailV2&ccid=BvO1M09J&id=D0BF66788A7757E9A02
5D3419BEFEF03F5C9B8AA&thid=OIP.BvO1M09JTILAn818LpvfIwHaHa&mediaurl=https%3a%2f%2fae
01.alicdn.com%2fkf%2fHTB1NOUpegKTBuNkSne1q6yJoXXab%2fMulti-Function-MiniKeyboardCleaning-brush-Vehicle-Anti-Static-Dust-Brush-Desktop-Sweeper-Cleaning-HomeDusting.jpg&exph=841&expw=841&q=Keyboard+Cleaning+Brush&simid=608038674591842660&ck
=37FFB6DE657D0F68581B0942D4263A76&selectedIndex=0&ajaxhist=0
https://www.slideshare.net/kenjoyb/k-to-12-pc-hardware-servicing-learning-module
For inquiries or feedback, please write or call:
Department of Education – Schools Division of Negros Oriental
Kagawasan, Avenue, Daro, Dumaguete City, Negros Oriental
Tel #: (035) 225 2376 / 541 1117
Email Address: negros.oriental@deped.gov.ph
Website: lrmds.depednodis.net
Download