Kappa Product data sheet
Kappa
Flexible application
Kappa readily allows the integration of unframed photovoltaic modules into
new and old roofs regardless of the type of roof covering. 1 Kappa is mounted
onto the existing roof battens and replaces the regular roof cladding.
Rapid mounting
All components (including the flashing) are pre-fitted according to the chosen
PV module and module configuration. Further reduction in installation time
and cost is achieved through a maximum of pre-assembly and the patented
click-system of the support rails.
High impermeability
In terms of impermeability Kappa fulfils the requirements of conventional tile
roofs. The special supporting profiles guarantee proper rear ventilation and
rainwater drainage.
In-roof
2
Unframed module
Orientation
portrait
Orientation
landscape
Double Roman
Tiles
Bitumen shingles
Slate
Individual array
The roof can be entirely or partly covered with modules. Essentially, all
connected module arrangements and integration of windows 3 are possible.
Appealing optics
Levelling the modules with the roof covering, Kappa is the most appealing
method of mounting PV modules.
Maximum service life
All profiles and flashings (aluminium), while being completely recyclable,
guarantee maximum service life through their high resistance to corrosion.
Plain Tiles
Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
years
Warranty
compliant
Mechanical load test
Avis Technique in progress
in progress
1 Kappa is compatible with nearly all types of tiles, formwork and slate coverings. For detailed information,
please contact us during the planning stages of your project.
2 Only possible if junction box is positioned at least 55 mm from the module edge.
3 Subject to previous checking.
Mechanical load test
in accordance with
IEC 61215:2005
Warning! Waterproofing the roof is heavily
Application
Pitched roof – roof integration
Roof cladding
Suitable for nearly all types of roof coverings
Roof slope
> 16° (lower upon request)
PV modules
Unframed 1
Total height of PV system
41 mm + height of laminate module
Module layout
Connected surface, as well as entire roof.
Integration of windows possible
Module thickness
<10 mm (>10 mm upon request)
Module orientation
Portrait, landscape 2
Module layout and position
Max. 5 modules vertically;
on the roof
max. 6 m roof above the PV field
Roof construction
The standard screws delievered are meant for
problems, we offer practical trainings.
h
a
b
c
g
Horizontal section
mounting on wooden battens sized 40 x 40 mm 3
Standards
Eurocode 1 — Actions on structures
c
Eurocode 9 — Design of aluminium structures
Certificates and material testing ·MPA Dresden: Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
·CEIAB: compliant
d
a
e
·CSTB: Mechanical load test 800 Pa
·CSTB: Avis Technique approval in progress with
GSS, First Hybrid Energy und Solarwatt
(No: 2010234 / LT1)
f
Side view
·ETN: approval in progress with KPV
·Mechanical load test 2.400 Pa (Conergy, Solon,
Solarwatt) and 2.400 / 5.400 Pa (KPV) according
to IEC 61215:2005
Supporting profiles
Extruded aluminium (EN AW 6063 T66)
Hooks, small parts
Stainless steel (V2A)
Flashings
Aluminium (EN AW 1050 A H16)
Seals
EPDM
Colour
Profiles/flashings: plate finish
a PV module
b Rubber profile
c Module-supporting profile
d Edge protection rubber
e Batten
fRafter
gDrainage
h Suction safeguarding
(colour coating optional)
Warranty
Kappa-TD-ENG-1304
Kappa Product data sheet
(subject to previous checking).
dependent on correct installation! To avoid
10 years 4
1 Compatible with nearly all current unframed modules.
For further information: www.mounting-systems.com
2 Only possible if junction box is positioned at least 55 mm from the module edge.
Subject to technical changes.
3 Variation on request; with adepted maximum permissible loads, installation on
2013 © Mounting Systems GmbH
thinner supports for example complete sheathing is also possible.
4 Please find the exact terms in the Mounting Systems GmbH Warranty document.
Theta Product data sheet
Theta
Flexible applications
Theta readily allows the integration of framed and unframed photovoltaic
modules into new and old roofs regardless of the type of roof covering ­ 1.
The system is mounted on top of the existing roof battens­and replaces
the regular roof cladding.
In-roof
High impermeability
Thanks to its substructure, the Theta meets the same requirements for
waterproofing as a conventional roof. The special a
­ dapters ensure optimum
ventilation­while transmitting the occuring loads into the roof structure 2.
Unframed module
Framed module
Orientation
portrait
Orientation
landscape
Individual array
The roof can be entirely or partly covered with modules­. Essentially, all
connected module arrangements and integration of windows are possible 3.
Double Roman
Tiles
Slate
Plain Tiles
Bitumen shingles
Appealing optics
The Theta blends in harmoniously with the roof skin and creates an
aesthetic module­mounting system.
Static reliability assured
Using Mounting Systems' configuration software, the material for any standard
configuration can be calculated in minutes, project-specific, auditable static
verification (based on the applicable national norms) included.
Installation in landscape orientation
Maximum service life
All components are made of extruded aluminium and stainless steel. This choice
of material guarantees both full recyclability and a maximum service life due to
high resistance to corrosion.
years
Warranty
1 The Theta-System is compatible with nearly all conventional types of roofing tile, formwork and slate roofing. Avis Technique
For detailed information, please contact us before you commence planning­­.
2 Complies with German roofing regulations. Any installation must also be in accordance with local roofing regulations­­.
3 Subject to previous checking.
Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
Application
Pitched roof – roof-integration
Roof cladding
Suitable for most types of roof cladding
Roof slope
14° to 45° (other slopes on request) 1
PV modules
Framed, unframed
Total height of PV system
Portrait: 41 mm + module height
Type of mounting
Flat
Module layout
Connected surfaces, as well as entire roof.
d
c
e
Horizontal section, landscape installation
b
a
Integration of windows possible (subject to
previous checking).
Module orientation
Landscape, portrait
Size of module array
Any size possible
Position of the module array
No special requirements
Roof structure
Battens as for conventional tile covering 2
Standards
Eurocode 1 – Actions on structures
Eurocode 9 – Design of aluminium structures
Certificates and material testing ·GS mark: Guaranteed Safety
·CSTB: Avis Technique with Conergy (No: 21/10-13)
and with REC (No: 21/12-28)
f
d
e
Horizontal section, portrait installation
a PV module
b Module clamp
c Adapter for landscape installation
d Corrugated sheet
e Roof batten
f Adapter for portrait installation
·MPA Dresden: Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
Supporting profiles
Extruded Aluminium (EN AW 6063 T66)
Small parts
Stainless steel (V2A)
Flashing (lateral and top)
Aluminium (EN AW 5005)
Corrugated metal
Aluminium (EN AW 3005)
Seals
EPDM
Colour
Profiles/sheeting: plate finish
Warranty
10 years 3
Warning! Waterproofing of the roof is heavily
dependent on correct installation!
To avoid problems, we offer you practical
trainings.
Theta-TD-ENG-1304
Theta Product data sheet
Landscape: 32 mm + module height
b
a
1 Complies with German roofing regulations. Any installation must also be in accordance
with local roofing regulations­­.
2 The standard screws are dimensioned for roof battens 30 x 50 mm in wood classification 10.
For further information: www.mounting-systems.com
Other on request.
Subject to technical changes.
3 Please find the exact terms in the Mounting Systems GmbH warranty document.
2013 © Mounting Systems GmbH
Zeta Product data sheet
Zeta
Flexible applications
Zeta readily allows the integration of framed photovoltaic modules into new
and old roofs regardless of the type of roof covering. 1 Zeta is mounted onto
the existing roof battens and replaces the regular roof cladding.
Rapid mounting
All components are pre-fitted according to the chosen PV module and
module configuration. Further reduction in installation time and simplification
is achieved through the patented click-system of the aluminum rails.
High impermeability
Zeta is based upon the in-roof-system Kappa for unframed modules, which
has already been used successfully for several years. In terms of impermeability
Zeta fulfils the requirements of conventional tile roofs. The special supporting
profiles guarantee proper rear ventilation and rainwater drainage. 3
In-roof
2
Framed module
Orientation
portrait
Orientation
landscape
Double Roman
Tiles
Slate
Plain Tiles
Bitumen shingles
Individual array
The roof can be entirely or partly covered with modules. The integration of
dormers and windows is possible as well. 4
Appealing optics
Levelling the modules with the roof covering, Zeta is the most appealing
method of mounting PV modules.
Maximum service life
All profiles and flashings (aluminium), while being completely recyclable,
guarantee maximum service life through their high resistance to corrosion.
years
Warranty
Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
1 Zeta system can be used with almost all types of tiles, formwork and roofing slates. For more information, please contact us before planning your installation.
compliant
2 Implies clamping of the modules on the short sides. Subject to previous checking.
3 The installation must be in accordance with local regulations for roof covering.
4 Subject to previous checking.
Pass Innovation vert
Application
Pitched roof – roof-integration
Roof cladding
Any roof cladding possible
Roof slope
16° to 45° (above on request) 1
PV modules
Framed
Total height of PV system
42 mm + height of module
Module layout
Connected surface, as well as entire roof.
Transverse section of supporting profile
Integration of windows possible
Dimension of modules
Any dimension possible
Module orientation
Portrait
Module layout and
Max. 5 modules vertically;
position on the roof
max. 6 m roof above the PV field
Building height
Up to 12 m (above on request)
Wind zone
3 (above on request) 2
Snow zone
C2, 400m a.s.l. (above on request) 2
Roof construction
The standard screws delivered are meant for
Lateral view of the transition between
2 rows of panels
mounting on wooden battens sized 40 x 60 mm 3
Standards
Eurocode 1 — Actions on structures
Eurocode 9 — Design of aluminium structures
Certificates and material testing ·MPA Dresden: Fire behaviour tests in accordance
with DIN EN 13501-5:2010-02
·CEIAB: compliant
·CSTB: Pass Innovation vert with Conergy, REC,
Panasonic, Solarwatt, Sharp (No: 2011-150,
View of upper sealing
2012-180)
Supporting profiles
Extruded aluminium (EN AW 6063 T66)
Small parts
Stainless steel (V2A)
Flashings
Aluminium (EN AW 1050A H16)
Seals
EPDM
Colour
Profiles: plate finish
Warning! Waterproofing the roof is heavily
dependent on correct installation! To avoid
problems, we offer practical trainings.
(colour coating optional)
Warranty
Zeta-TD-ENG-1304
Zeta Product data sheet
(subject to previous checking).
10 years 4
1 The installation must be in accordance with local regulations for roof covering.
2 French wind and snow zones, based on the French appendixes to the Eurocode 1 „Annexe nationale à la NF
EN 1991-1-4:2005“ and „Annexe nationale à la NF EN 1991-1-3:2004“
3 Variation on request; with adepted maximum permissible loads, installation on thinner supports for
For further information: www.mounting-systems.com
example complete sheathing is also possible.
Subject to technical changes.
4 Please find the exact terms in the Mounting Systems GmbH Warranty document.
2013 © Mounting Systems GmbH