CENTRIA Exposed Fastener Series™ Metal Roof Panels
CENTRIA Exposed Fastener Series™ Metal Roof Panels are a versatile design choice for both new
and retrofit projects. Panels are manufactured in many different coil coating systems and painted with a
wide variety of manufacturer's standard colors plus an unlimited choice of custom colors. Basic coil
materials are galvanized steel, Galvalume® and Galvalume Plus® coated steel, aluminum, and a
distinctive moderately reflective stainless steel. CENTRIA Profile Series™ Metal Roof Panels are available
with a flat or embossed exterior surface. Accessories are available for most applications.
CENTRIA Exposed Fastener Series™ Metal Roof Panels are manufactured and coated with CENTRIA's own
Fluorofinish® Kynar 500® or Hylar 5000®-based fluoropolymer or Versacor® corrosion- and abrasionresistant finishes. Highly UV resistant and durable in the face of chemical and air borne pollution, salt
spray and wind-driven sand, CENTRIA coatings set the standard for the industry. CENTRIA coatings are
available in over 60 standard colors and additional custom colors.
Consult your local CENTRIA architectural representative for design assistance. Contact CENTRIA,
Pittsburgh, PA, (800)759-7474, Email: info@centria.com, www.centria.com for a list of offices.
CENTRIA is a world leader in the manufacture of metal building products and systems for nonresidential
walls and roofs. CENTRIA is also a world-class coil coater, coating a wide range of products for
customers in numerous industries.
CENTRIA products appear in the following MasterFormat sections:
● Section 07 41 13 – Metal Roof Panels (SRS3)
● Section 07 41 16 – Insulated Core Metal Roof Panels (Versapanel)
● Section 07 42 13 – Metal Wall Panels (Cascade Metal Panel System, Intercept V-Trac, Intercept
Entyre, Paradigm EXP, Paradigm CFP, Concept Series, IW Series, Exposed Fastener Panels)
● Section 07 42 16 – Insulated-Core Metal Wall Panels (Formawall Dimension Series, Formawall
Graphix Series, Versawall, Versapanel, Foamwall, VersaShield MW)
● Section 07 42 17 – Insulated Composite Backup Panel (MetalWrap)
● Section 07 42 43 – Composite Wall Panels (FormaBond)
Specifier: This document is organized according to CSI MasterFormat™. Edit section number and title
as appropriate to the Project. Bold items require specifier selection. Convert bold to plain text and
delete notes before publishing.
Exposed Fastener Series™ is a trademark of CENTRIA, Inc.
Fluorofinish® and Versacor® are a registered trademarks of CENTRIA, Inc.
Galvalume® and Galvalume Plus® are registered trademarks of BIEC International, Inc.
Kynar 500® is a registered trademark of Arkema, Inc.
Hylar 5000® is a registered trademark of Solvay S.A.
MasterFormat™ is a trademark of the Construction Specifications Institute.
This document is Copyright© 2014 CENTRIA. All rights reserved.
CENTRIA
07 41 13
Page 1 of 16
Metal Roof Panels
SECTION 07 41 13
METAL ROOF PANELS
PART 1 - GENERAL
1.1
SECTION INCLUDES
A.
1.2
Exposed fastener metal roof panels[, and liner panels].
RELATED REQUIREMENTS
Specifier: Edit list below to correspond to Project.
A.
Division 01 Section "Sustainable Design Requirements" for related LEED general requirements.
B.
Division 05 Section "Cold-Formed Metal Framing" for cold-formed metal framing supporting
metal roof panel.
C.
Division 05 Section "Steel Decking" for steel roof deck supporting metal roof panels.
D.
Division 07 Section "Thermal Insulation" for field installed thermal insulation.
E.
Division 07 Section "Metal Wall Panels" for factory-formed metal wall and soffit panels.
F.
Division 07 Section "Sheet Metal Flashing and Trim" for sheet metal copings, flashings, reglets
and roof drainage items not specified in this Section.
G.
Division 07 Section "Manufactured Roof Specialties" for manufactured copings, reglets, and roof
drainage items.
H.
Division 07 Section "Roof Accessories" for roof hatches, smoke vents, equipment curbs, and
equipment supports.
I.
Division 07 Section "Joint Sealants" for field-applied joint sealants.
1.3
DEFINITIONS
A.
1.4
Metal Roof Panel System: Metal roof panels with exposed fastener attachment, [supplemental
framing members required for complete metal framing attachment system], and accessories
necessary for a complete watertight installation.
REFERENCES
A.
American Architectural Manufacturer's Association (AAMA):
1.
2.
CENTRIA
AAMA 620 - Voluntary Specification for High Performance Organic Coatings on Coil
Coated Architectural Aluminum Substrates.
AAMA 621 - Voluntary Specification for High Performance Organic Coatings on Coil
Coated Architectural Hot Dipped Galvanized (HDG) and Zinc-Aluminum Coated Steel
Substrates.
07 41 13
Page 2 of 16
Metal Roof Panels
B.
American Iron and Steel Institute (AISI):
1.
C.
American Society of Civil Engineers (ASCE):
1.
D.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
CENTRIA
Energy Star Reflective Roof Products.
US Green Building Council (USGBC):
1.
I.
UL 580 – Tests for Uplift Resistance of Roof Assemblies.
UL Fire Resistance Directory.
UL Roofing Materials Directory.
US Environmental Protection Agency:
1.
H.
Architectural Sheet Metal Manual.
Underwriters Laboratories, Inc. (UL):
1.
2.
3.
G.
ASTM A 653/ A 653M - Specification for Steel Sheet, Zinc-Coated (Galvanized) or ZincIron Alloy-Coated (Galvannealed) by the Hot-Dip Process.
ASTM A 666 – Standard Specification for Annealed or Cold Worked Austenitic Stainless
Steel Sheet, Strip, Plate and flat bar.
ASTM A 755/A 755M - Specification for Steel Sheet, Metallic Coated by the Hot-Dip
Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building
Products.
ASTM A 792/A 792M – Specification for Steel Sheet, 55 percent Aluminum-Zinc Alloy
Coated by the Hot Dip Process.
ASTM B 209 - Specification for Aluminum and Aluminum Alloy Sheet and Plate.
ASTM C 920 - Specification for Elastomeric Joint Sealants.
ASTM D 2244 - Test Method for Calculation of Color Differences from Instrumentally
Measured Color Coordinates.
ASTM D 4214 - Test Methods for Evaluating Degree of Chalking of Exterior Paint Films.
ASTM E 84 - Test Methods for Surface Burning Characteristics of Building Materials.
ASTM E 119 - Test Methods for Fire Tests of Building Construction and Materials.
ASTM E 283 - Test Method for Determining the Rate of Air Leakage Through Exterior
Windows, Curtain Walls, and Doors under Specified Pressure Differences across the
Specimen.
ASTM E 331 - Test Method for Water Penetration of Exterior Windows, Curtain Walls, and
Doors by Uniform Static Air Pressure Difference.
ASTM E 1980 - Practice for Calculating Solar Reflectance Index of Horizontal and LowSloped Opaque Surfaces.
Sheet Metal and Air Conditioning Contractors National Association, Inc. (SMACNA):
1.
F.
ASCE 7 - Minimum Design Loads for Buildings and Other Structures.
ASTM International (ASTM):
1.
E.
Specification for the Design of Cold-Formed Steel Structural Members.
Leadership in Energy and Environmental Design (LEED).
International Organization of Standardization (ISO)
07 41 13
Page 3 of 16
Metal Roof Panels
1.
1.5
ISO 14025 Environmental labels and declarations – Type III environmental declaration –
Principles and procedures.
PERFORMANCE REQUIREMENTS
Specifier: Add requirements to this Article if Project requirements include delegated design by
Contractor.
A.
General: Provide metal roof panel system meeting performance requirements as determined by
application of specified tests by a qualified testing agency on manufacturer's standard
assemblies.
Specifier: Retain Air Infiltration and Water Penetration paragraphs below for those CENTRIA products
tested to the referenced standards. Also retain if assembly utilizes CENTRIA metal liner panels to serve
as the air and water barrier. Verify with CENTRIA representative.
B.
Air Infiltration: Maximum 0.06 cfm/sq. ft. (0.3 L/s per sq. m) per ASTM E 283 at a static-airpressure difference of 6.24 lb. /sq. ft. (299 Pa), using minimum 10-by-10 foot (3050-by3050 mm) test panel that includes side joints.
C.
Water Penetration, Static Pressure: No uncontrolled water penetration per ASTM E 331 at a
minimum static differential pressure of 15 lb. /sq. ft. (718 Pa), using minimum 10-by-10 foot
(3050-by-3050 mm) test panel that includes side joints.
Specifier: UL 580 Wind Uplift Resistance performance below applies to BR5-36, Style-Rib & TR4-36
Exposed Fastener Profile Series panels. Verify performance with CENTRIA representative.
D.
Wind Uplift Resistance: [UL 580 wind uplift rating UL 90] [Per ASCE/SEI 7 and uplift design
pressures indicated on Drawings].
Specifier: Retain “Florida State Building Code Compliance” paragraph below when required for BR5-36,
Style-Rib or Econolap ¾” panels.
E.
Florida State Building Code Compliance: Provide roof panels that comply with the
requirements for installation under Florida State Building Code aside of the High Velocity
Hurricane Zone. BR5-36, Style-Rib & Econolap ¾” only.
F.
Thermal Movements: Allow for thermal movements from variations in both ambient and
internal temperatures. Accommodate movement of support structure caused by thermal
expansion and contraction.
Specifier: Retain paragraph below if foam plastic insulation is included within the roof system.
G.
Roof systems that incorporate foam plastic insulation must be tested by the foam plastic
supplier in accordance with NFPA-285.
Specifier: Retain one or more energy performance subparagraphs below based on project requirements.
Retain Energy Star reference for projects seeking Energy Star rating; products must be listed on EPA
Energy Star website. Retain CEC compliance for projects required to comply with CEC requirements.
Verify values with manufacturer for selected panel finishes.
CENTRIA
07 41 13
Page 4 of 16
Metal Roof Panels
H.
Energy Performance:
1.
2.
3.
1.6
Solar Reflectance Index: Minimum 78 for roof slopes of 2:12 or less and 29 for roof
slopes greater than 2:12 per ASTM E 1980.
Energy Star Qualified: Listed on USDoE ENERGY STAR Roof Products Qualified Product
List www.energystar.com.
California Energy Commission Compliance: Minimum initial solar reflectance of [0.70]
and emissivity of [0.75] per CRRC-1, www.coolroofs.org.
QUALITY ASSURANCE
A.
Manufacturer/Source:
manufacturer.
Provide metal roof panels and panel accessories from a single
Specifier: Retain and edit subparagraph below if work of this Section is required to be supplied by same
manufacturer of a related product in another section.
1.
Provide products by same manufacturer as manufacturer of products specified in Division
[00] Section "[Insert Division number and Section name]."
Specifier: Retain paragraph below if Owner allows substitutions but requires strict control over qualifying
of substitutions.
B.
Manufacturer Qualifications: Approved manufacturer listed in this Section with minimum 5
years experience in manufacture of similar products in successful use in similar applications.
1.
Approval of Comparable Products: Submit the following in accordance with project
substitution requirements, within time allowed for substitution review:
a.
b.
c.
d.
e.
2.
3.
C.
Product data, including certified independent test data indicating compliance with
requirements.
Samples of each component.
Sample submittal from similar project.
Project references: Minimum of 5 installations not less than 5 years old, with
Owner and Architect contact information.
Sample warranty.
Substitutions following award of contract are not allowed except as stipulated in Division
01 General Requirements.
Approved manufacturers must meet separate requirements of Submittals Article.
Installer Qualifications: Experienced Installer with minimum of 5 years experience with
successfully completed projects of a similar nature and scope.
Specifier: Retain and edit subparagraph below if work of this Section is required to be installed by same
Installer of a related product in another section.
1.
Provide work installed by same Installer as Installer of products specified in Division [00]
Section "[Insert Division number and Section name]."
Specifier: Retain below when metal roof panels are part of a fire-resistance-rated roof assembly.
CENTRIA
07 41 13
Page 5 of 16
Metal Roof Panels
2.
1.7
Fire Resistance Ratings: Provide metal roof panel system tested as part of a roof
assembly listed in UL Fire Resistance Directory.
ADMINISTRATIVE REQUIREMENTS
A.
Preinstallation Meeting: Prior to erection of metal roof panels , conduct preinstallation meeting
at site attended by Owner, Architect, manufacturer's technical representative, inspection agency
and related trade contractors.
1.
2.
3.
1.8
Coordinate building framing in relation to metal roof panels.
Coordinate openings and penetrations of metal roof panels.
Coordinate work of Division 07 Sections "Roof Specialties" and "Roof Accessories" and
roof openings and penetrations and manufacturer's accessories with installation of metal
roof panels.
ACTION SUBMITTALS
A.
Product Data: Manufacturer’s data sheets, for specified products.
1.
B.
Include data indicating compliance with performance requirements.
Shop Drawings: Show layouts of metal roof panels. Include details of each condition of
installation, panel profiles, and attachment to building. Provide details at a minimum scale 11/2-inch per foot of edge conditions, joints, fastener and sealant placement, flashings,
penetrations, and special details. Make distinctions between factory and field assembled work.
1.
2.
3.
Include data indicating compliance with performance requirements.
Indicate points of supporting structure that must coordinate with metal roof panel system
installation.
Include data indicating compliance with requirements of local authorities having
jurisdiction.
C.
Samples for Initial Selection: For each product specified including sealants and gaskets.
Provide representative color charts of manufacturer's full range of colors.
D.
Samples for Verification: Provide 12-inch (305 mm) long section of metal roof panel showing
finishes, vertical joint return, and anchoring details. Provide 12-inch (305 mm) long pieces of
trim.
1.9
INFORMATIONAL SUBMITTALS
A.
Product Test Reports: Indicating compliance of products with requirements, from a qualified
independent testing agency, when requested by Architect.
Specifier: Retain “Dade County Approval” paragraph below when required for Style-Rib panel (20 gage
only).
B.
Dade County Approval ; Dade County Notice of Acceptance (NOA).
Specifier: Retain paragraph below when Project requirements include compliance with Federal Buy
American provisions.
CENTRIA
07 41 13
Page 6 of 16
Metal Roof Panels
C.
Buy American Act Certification: Submit documentation certifying that products comply with
provisions of the Buy American Act 41 U.S.C 10a – 10d.
D.
Qualification Information: For Installer firm and Installer’s field supervisor.
E.
Manufacturer's warranty: Submit sample warranty.
1.10
A.
1.11
A.
CLOSEOUT SUBMITTALS
Maintenance data.
DELIVERY, STORAGE, AND HANDLING
Protect products of metal roof panels during shipping, handling, and storage to prevent
staining, denting, deterioration of components or other damage. Protect panels and trim
bundles during shipping with water resistant paper. Protect painted surfaces with a strippable
protective covering before shipping.
1.
2.
1.12
A.
Deliver, unload, store, and erect metal roof panels and accessory items without
misshaping panels or exposing panels to surface damage from weather or construction
operations.
Store in accordance with Manufacturer's written instruction. Provide wood collars for
stacking and handling in the field.
WARRANTY
Special Manufacturer’s Warranty: On Manufacturer’s standard form, in which Manufacturer
agrees to repair or replace components of metal roof panel installation that fail in materials and
workmanship within [two] years from date of Substantial Completion.
Specifier: Consult CENTRIA representative to verify available finish warranty.
B.
Special Panel Finish Warranty: On Manufacturer’s standard form, in which Manufacturer agrees
to repair or replace metal roof panels that display evidence of deterioration of factory-applied
finish within [20] years from date of Substantial Completion, including:
1.
2.
3.
Color fading in excess of 5 Hunter units per ASTM D 2244.
Chalking in excess of No. 8 rating per ASTM D 4214.
Failure of adhesion, peeling, checking, or cracking.
PART 2 - PRODUCTS
2.1
SYSTEM DESCRIPTION
Exposed Fastener, Metal Roof Panels: Structural metal roof panel consisting of roll formed metal sheets
forming structural ribbed shapes, installed by overlapping edges of adjacent panels.
Specifier: Retain one or more of the three roof assembly descriptions below that meet the Project
requirements; Edit as required.
CENTRIA
07 41 13
Page 7 of 16
Metal Roof Panels
A. Metal Roof Panels over uninsulated framed structural supports: Single-skin exposed fastener
metal roof panels installed as an exterior roof over framing specified in [Division 05 Section “Cold
Formed Metal Framing” ] [Division 13 Section “Metal Building Systems].
B. Metal Roof Panels and Metal Liner Panel System: Single-skin exposed fastener metal roof
panels installed as the exterior panels over roof framing specified in [Division 05 Section “Cold
Formed Metal Framing”] [Division 13 Section “Metal Building Systems”] with glass fiber insulation
and metal liner panels. Metal roof panel installation specified in this section includes secondary metal
subgirt framing for panel attachment and an interior sealed-joint metal liner panels that provides air
and water vapor control.
C. Metal Roof Panels over framed structural supports with draped insulation: Single-skin
exposed fastener metal roof panels installed as the exterior panels over roof framing specified in
[Division 05 Section “Cold Formed Metal Framing”] [Division 13 Section “Metal Building Systems”]
with insulation laminated to a flexible vapor retarder facing, draped over the framing members.
Standard glass fiber blanket insulation with a 6.0 pcf (9.61 kg/m3) density and moisture resistant
laminate facing shall be maximum of [3”] [> 3” to 6”, with thermal spacers] thick.
2.2
MANUFACTURERS
A.
Basis of Design: CENTRIA, Profile Series Exposed Fastener Metal Roof Panels. Provide
basis of design product [, or comparable product approved by Architect prior to bid].
1.
2.3
CENTRIA Architectural Systems; Moon Township, PA 15108-2944. Tel: (800)759-7474.
Tel: (412)299-8000. Fax: (412)299-8317. Email: info@CENTRIA.com.
Web:
www.CENTRIA.com.
PANEL MATERIALS
A.
Metallic-Coated Steel Face Sheet: Coil-coated, ASTM A 755/A 755M.
Specifier: Select metal roof panel face material from three paragraphs below. Aluminum-zinc alloycoated steel sheet, Galvalume, Galvalume Plus with a thin, clear acrylic topcoat, is also available and is
recommended for uniform weathering when specified without an applied paint finish. Galvalume
substrates are eligible for extended warranty from CENTRIA.
1.
2.
Zinc-Coated (Galvanized) Steel Sheet: ASTM A 653/A 653M, G90 (Class Z275), structural
steel quality.
Aluminum-zinc Alloy-coated (Galvalume) Steel Sheet: ASTM A 792/A 792 M, Class AZ50
Grade 50 (Class AZM150, Grade 275), structural steel quality.
Specifier: Select required metal face sheet thickness from options below. CENTRIA recommends the use
of minimum 22 gage metal roof panels to achieve enhanced structural performance and optimum
aesthetic appearance. CENTRIA exposed fastener metal roof panels, except for Super Rib, are also
available in 24 gage. Aluminum-zinc alloy-coated steel sheet (Galvalume) is available for 22 and 24
gauge sheet.
3.
4.
CENTRIA
Face Sheet: Minimum [0.024 inch/24 gage (0.60 mm)] [0.030 inch/22 gage (0.76 mm)]
[0.036 inch/20 gage (0.91 mm)] [0.047 inch/18 gage (1.19 mm)] nominal uncoated
thickness.
Surface: [Smooth] [Non-Directional Embossed].
07 41 13
Page 8 of 16
Metal Roof Panels
B.
Aluminum Face Sheet: Smooth surface coil-coated, ASTM B 209, 3003-H14 or 5052-H32
alloy.
Specifier: Select required metal face sheet thickness from options below. MR3 and Super-Rib panels are
available in .040 and .050 inch only.
1.
2.
C.
Face Sheet: [0.032 inch (0.8 mm)] [0.040 inch (1.0 mm)] [0.050 inch (1.27 mm)]
nominal thickness.
Surface: [Smooth] [Non-directional embossed].
Stainless-Steel Face Sheet: ASTM A 666, architectural grade alloy type as indicated.
Specifier: Select required metal face sheet thickness from options below. Super-Rib panels are not
available in stainless steel.
1.
Face Sheet: [0.024 inch/24 gage (0.60 mm)] [0.030 inch/22 gage (0.76 mm)] [0.036
inch/20 gage (0.91 mm)] nominal thickness.
Specifier: Type 316 alloy is recommended for marine and other corrosive environments.
2.
2.4
Finish: [Type 304], [Type 316], #4 Brushed
EXPOSED FASTENER METAL ROOF PANELS
If using more than one metal roof panel, retain the drawing designation below for each panel. If metal
types, thicknesses, surfaces, or finish systems differ, add notes below to indicate the metal type,
thickness, surface, and finish for each panel on project.
A.
Metal Roof Panels, General: Factory-formed, Exposed fastener panels with interconnecting side
joints, fastened to supports with exposed fasteners, with field-applied sealants in side laps as
required to meet performance requirements.
B.
Ribbed profile with lap joint MRP_____:
1.
2.
3.
4.
C.
Ribbed profile with lap joint MRP_____:
1.
2.
3.
4.
D.
Basis of Design Product: CENTRIA, MR3-36.
Panel Coverage: 36 inches (914 mm).
Panel Height: 3.0 inches (76 mm).
Rib Spacing: 3 at 12 inches (305 mm) o.c.
Ribbed profile with raised pans with lap joint MRP_____:
1.
2.
3.
4.
CENTRIA
Basis of Design Product: CENTRIA, BR5-36.
Panel Coverage: 36 inches (914 mm).
Panel Height: 1.50 inches (38 mm).
Rib Spacing: 5 at 7.20 inches (183 mm) o.c.
Basis of Design Product: CENTRIA, TR4-36.
Panel Coverage: 36 inches (914 mm).
Panel Height: 1.50 inches (38 mm).
Rib Spacing: 4 at 9 inches (229 mm) o.c.
07 41 13
Page 9 of 16
Metal Roof Panels
E.
Symmetrical corrugated profile with lap joint. MRP_____:
1.
2.
3.
4.
F.
Symmetrical corrugated profile with lap joint MRP_____:
1.
2.
3.
4.
G.
Basis of Design Product: CENTRIA, Econolap 1/2 inch.
Panel Coverage: 37.33 inches (948 mm).
Panel Height: 0.50 inches (13 mm).
Corrugation Spacing: 2.66 inches (68 mm) o.c.
Symmetrical deep rib profile with lap joint MRP_____:
1.
2.
3.
4.
H.
Basis of Design Product: CENTRIA, Econolap 3/4 inch.
Panel Coverage: 34.66 inches (880 mm).
Panel Height: 0.75 inches (19 mm).
Corrugation Spacing: 2.66 inches (68 mm) o.c.
Basis of Design Product: CENTRIA, Super-Rib.
Panel Coverage: 24 inches (610 mm).
Panel Height: 4 inches (102 mm).
Rib Spacing: 12 inches (305 mm) o.c.
Symmetrical rib profile with lap joint MRP_____:
1.
2.
3.
4.
Basis of Design Product: CENTRIA, Style-Rib.
Panel Coverage: 36 inches (914 mm).
Panel Depth: 1.50 inches (38 mm).
Rib Spacing: 5 at 7.2 inches (183 mm) o.c.
Specifier: Select metallic-coated steel face sheet or aluminum face sheet finish system from options
below. AAMA 620 is aluminum sheet finish standard; AAMA 621 is metallic-coated steel sheet finish
standard. Delete article if retaining stainless steel material above.
For projects with sustainable design requirements, verify with manufacturer that selected finish and color
meet SRI requirements in Part 1.
A.
Exposed Coil-Coated Finish System:
1.
Fluoropolymer Two-Coat System: 0.2 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat, AAMA [620] [621].
a.
2.
Fluoropolymer Two-Coat System: 0.8 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat, AAMA [620] [621].
a.
3.
Basis of Design: CENTRIA Duragard.
Fluoropolymer Three-Coat System:
0.8 mil primer, 0.8 mil 70 percent PVDF
fluoropolymer color coat, and a 0.8 mil 70 percent PVDF fluoropolymer clear coat,
AAMA [620] [621].
a.
CENTRIA
Basis of Design: CENTRIA Fluorofinish.
Basis of Design: CENTRIA Duragard Plus.
07 41 13
Page 10 of 16
Metal Roof Panels
4.
Fluoropolymer Two-Coat Mica System: 0.2 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat providing a pearlescent appearance, AAMA [620] [621].
a.
5.
Basis of Design: CENTRIA Sundance Mica.
Fluoropolymer Three-Coat Metallic System: 0.2 mil primer, 0.8-mil 70 percent PVDF
fluoropolymer color coat containing metal flakes, and a 0.5-mil 70 percent PVDF
fluoropolymer clear coat, AAMA [620] [621].
a.
Basis of Design: CENTRIA Sundance AM.
Specifier: The three CENTRIA Versacor systems below are recommended for corrosive and abusive
environments. Select system and one of three options for panel interior finish based on exposure and
environmental conditions. Consult CENTRIA representative for recommended finish system.
6.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat.
a.
7.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat that includes mica flakes
that provides a pearlescent appearance.
a.
8.
Basis of Design: CENTRIA KolorShift.
Fluoropolymer Three Coat System: 0.65 mil color base coat and Primer with a 0.05 mil
PVDF ink coat and a 0.45 nominal PVDF fluoropolymer clear coat.
a.
11.
Basis of Design: CENTRIA Versacor Elite AM.
Fluoropolymer Three Coat System: 0.2 mil primer with a 0.5 mil polyester base coat and
a 0.8 mil nominal PVDF fluoropolymer top coat providing an iridescent finish.
a.
10.
Basis of Design: CENTRIA Versacor Elite MX.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat that includes aluminum
metal flakes, with a 0.5 mil PVDF clear topcoat.
b.
9.
Basis of Design: CENTRIA Versacor Elite PF.
Basis of Design: CENTRIA Allusion.
Fluoropolymer Two Coat System: 0.2 mil primer with a 0.8 mil PVDF matte, low gloss
color coat with fine aggregate finish.
a.
Basis of Design: CENTRIA Allura.
Specifier: Retain paragraph below along with selected finish system above, and edit as required.
12.
B.
CENTRIA
Interior Finish System: [Manufacturer's standard] [Match exterior panel finish system]
[Specifier: Insert name of interior finish system].
Color:
07 41 13
Page 11 of 16
Metal Roof Panels
Specifier: Retain one or both subparagraphs below as required for Project.
1.
2.
2.5
Exterior Surface: [As indicated] [As selected by Architect from manufacturer's standard
colors] [Match Architect's custom color].
Interior Surface: [Manufacturer's standard primer color] [As indicated] [As selected by
Architect from manufacturer's standard colors] [Match Architect's custom color].
METAL LINER PANELS
Specifier: Retain this section if liner panel is required on interior of roof assembly. Standard lengths are
5 to 30 feet; custom length panels are available on special order. Deeper assemblies may be used in
conjunction with thicker insulation.
A.
Metal Liner Panels, General: Factory-formed panels with interconnecting side joints, fastened
to supports with exposed fasteners.
1.
2.
3.
4.
B.
Metal liner panel MLP#___:
1.
2.
3.
4.
C.
Basis of Design Product: CENTRIA, L2-2.
Panel Coverage: 24 inches (610 mm).
Panel Height: 2 inches (50 mm).
Stiffening Beads: Two.
Metal liner panel MLP#___:
1.
2.
3.
4.
E.
Basis of Design Product: CENTRIA, L2.
Panel Coverage: 24 inches (610 mm).
Panel Height: 1.375 inches (35 mm).
Stiffening Beads: Two.
Metal liner panel MLP#___:
1.
2.
3.
4.
D.
[Zinc-Coated (Galvanized) steel sheet] [Aluminum-zinc alloy-coated (Galvalume) steel
sheet].
Face Sheet: Minimum [0.024 inch/24 gage (0.60 mm)] [0.030 inch/22 gage (0.76 mm)]
[0.036 inch/20 gage (0.91 mm)] [0.047 inch/18 gage (1.19 mm)] nominal uncoated
thickness.
Panel Sheet: [Solid] [Perforated, with 10 percent free area].
Surface: [Smooth] [Non-Directional Embossed].
Basis of Design Product: CENTRIA, L2-3.
Panel Coverage: 24 inches (610 mm).
Panel Height: 3 inches (76 mm).
Stiffening Beads: Two.
Exposed Coil-Coated Finish System:
1.
Fluoropolymer Two-Coat System:
0.2-mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat, AAMA 621.
a.
CENTRIA
Basis of Design: CENTRIA Fluorofinish.
07 41 13
Page 12 of 16
Metal Roof Panels
2.
Fluoropolymer Two-Coat System: 0.8 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat, AAMA 621.
a.
3.
Fluoropolymer Three-Coat System: 0.8 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat, and a 0.8 mil 70 percent PVDF fluoropolymer clear coat,
AAMA 621.
a.
4.
Basis of Design: CENTRIA Duragard Plus.
Fluoropolymer Two-Coat Mica System: 0.2 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat providing a pearlescent appearance, AAMA 621.
a.
5.
Basis of Design: CENTRIA Duragard.
Basis of Design: CENTRIA Sundance Mica.
Fluoropolymer Three-Coat Metallic System: 0.2 mil primer with 0.8 mil 70 percent PVDF
fluoropolymer color coat containing metal flakes, and a 0.5 mil 70 percent PVDF
fluoropolymer clear coat, AAMA 621.
a.
Basis of Design: CENTRIA Sundance AM.
Specifier: The three CENTRIA Versacor systems below are recommended for corrosive and abusive
environments. Select system and one of three options for panel interior finish based on exposure and
environmental conditions. Consult CENTRIA representative for recommended finish system.
6.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat.
b.
7.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat that includes mica flakes
that provides a pearlescent appearance.
c.
8.
Basis of Design: CENTRIA KolorShift.
Fluoropolymer Three Coat System: 0.65 mil color base coat and Primer with a 0.05 mil
PVDF ink coat and a 0.45 nominal PVDF fluoropolymer clear coat.
a.
CENTRIA
Basis of Design: CENTRIA Versacor Elite AM.
Fluoropolymer Three Coat System: 0.2 mil primer with a 0.5 mil polyester base coat and
a 0.8 mil nominal PVDF fluoropolymer top coat providing an iridescent finish.
b.
10.
Basis of Design: CENTRIA Versacor Elite MX.
Fluoropolymer Two-Coat Corrosion and Abrasion Resistant System: 2.0 mil barrier coat
primer with 0.8 mil 70 percent PVDF fluoropolymer color coat that includes aluminum
metal flakes, with a 0.5 mil PVDF clear topcoat.
d.
9.
Basis of Design: CENTRIA Versacor Elite PF.
Basis of Design: CENTRIA Allusion.
07 41 13
Page 13 of 16
Metal Roof Panels
11.
Fluoropolymer Two Coat System: 0.2 mil primer with a 0.8 mil PVDF matte, low gloss
color coat with fine aggregate finish.
a.
F.
Basis of Design: CENTRIA Allura.
Color:
Specifier: Retain one or both subparagraphs below has required for Project.
1.
2.
2.6
Interior Exposed Surface: [As indicated] [As selected by Architect from manufacturer's
standard colors] [Match Architect's custom color].
Concealed Surface: Manufacturer's standard primer color.
METAL ROOF PANEL ACCESSORIES
A.
Provide complete metal roof panel assembly incorporating trim, copings, fasciae, soffits,
downspouts, insulation spacers, closures, and miscellaneous flashings. Provide required
fasteners, gaskets, closure strips, and sealants. Fabricate and install accessories in accordance
with SMACNA Manual.
1.
B.
Flashing and Trim: Match material, thickness, and finish of metal roof panels.
Panel Fasteners:
Self-tapping screws, bolts, nuts, and other acceptable fasteners
recommended by roof panel manufacturer. Provide corrosion-resistant fasteners with heads
matching color of metal panels by means of factory-applied coating.
1.
2.
Exposed Screws: Manufacturer's recommended stainless steel screws with bonded
neoprene and stainless steel washers, coated to match panel color.
Concealed Screws: Manufacturer's recommended corrosion resistant carbon steel with
corrosion resistant coating.
C.
Panel Sealants:
1.
Field Applied Unexposed Sealant: Side Laps, end laps, and flashing details: Gun grade,
nonskinning, butyl elastomer or polymeric non-skinning butyl tape.
2.
Exposed Sealant: ASTM C 920; elastomeric polyurethane, polysulfide, or silicone sealant;
of type, grade, class, and use classifications required to seal joints in metal roof panels
and remain weathertight; as recommended by metal roof panel manufacturer colored to
match panel color.
D.
Closures:
1.
Metal: Matching metal roof panel material, thickness, and finish, precut to match panel
profile.
2.
Foam: Precut to match panel profile.
E.
Pipe Flashings: Molded EPDM, with metal collar.
2.7
SECONDARY METAL FRAMING
A.
CENTRIA
Miscellaneous Framing Components, General:
ASTM A 653/A 653M, G90 (Z180).
07 41 13
Page 14 of 16
Cold-formed metallic-coated steel sheet,
Metal Roof Panels
1.
2.
Hat Channels: 0.0598 inch/16 ga. (1.52 mm) minimum – nominal thickness.
Sill Channels: 0.0598 inch/16 ga. (1.52 mm) minimum – nominal thickness.
PART 3 - EXECUTION
3.1
EXAMINATION
A.
Examine metal roof panel installation substrate with Installer present. Inspect for erection
tolerances and other conditions that would adversely affect installation of metal roof panels.
B.
Roof Substrate: Confirm that wall substrate is within tolerances acceptable to metal roof panel
system manufacturer.
1.
Maximum deviations acceptable:
a.
b.
1/4 inch in 20 feet (6 mm in 6.1 m) out of plane
1/2 inch (12.7 mm) over entire roof
C.
Framing: Inspect framing that will support metal roof panel system to determine if support
components are installed as indicated on approved shop drawings. Confirm presence of
acceptable framing members at recommended spacing to match installation requirements of
metal roof panels.
D.
Advise G.C., in writing, of out-of-tolerance work and other deficient conditions prior to
proceeding with metal wall panel system installation.
E.
Correct out of tolerance work and other deficient conditions prior to proceeding with panel
installation.
3.2
INSTALLATION
A.
General: Install metal roof panel system in accordance with approved shop drawings and
manufacturer's recommendations. Install metal roof panels in orientation, sizes, and locations
indicated. Install metal roof panels in one piece lengths from the ridge to eave unless
otherwise indicated on approved shop drawings. Anchor panels and other components securely
in place. Provide for thermal and structural movement.
B.
Attach panels to metal framing using recommended screws, fasteners, sealants, and adhesives
indicated on approved shop drawings.
1.
2.
3.
CENTRIA
Fasten metal roof panels to supports with exposed fasteners at location, spacing
recommended by manufacturer, and with fasteners recommended by manufacturer.
Anchor to supports with self-tapping fasteners approved by manufacturer.
Provide weatherproof escutcheons for pipe and conduit penetrating roof.
Dissimilar Materials: Where elements of metal roof panels installation will come into
contact with dissimilar materials, treat faces and edges in contact with dissimilar
materials as recommended by manufacturer.
07 41 13
Page 15 of 16
Metal Roof Panels
3.3
ACCESSORY INSTALLATION
A.
General: Install metal roof panel accessories with positive anchorage to building and weather
tight mounting and provide for thermal expansion. Coordinate installation with flashings and
other components.
1.
2.
3.
4.
3.4
Install related flashings and sheet metal trim per requirements of Division 07 Section
"Sheet Metal Flashing and Trim."
Install components required for a complete metal roof panel assembly, including trim,
copings, flashings, sealants, gaskets, fillers, closure strips, and similar items.
Comply with performance requirements, requirements of authorities having jurisdiction,
and manufacturer's written installation instructions.
Set units true to line and level as indicated. Install work with laps, joints, and seams that
will be permanently watertight and weather resistant.
CLEANING AND PROTECTION
A.
Remove temporary protective films when directed by Architect. Remove metal filings and
residue. Clean finished surfaces as recommended by metal roof panel manufacturer.
B.
Replace damaged panels and accessories that cannot be repaired to the satisfaction of the
Architect.
END OF SECTION
CENTRIA
07 41 13
Page 16 of 16
Metal Roof Panels