NZQA unit standard 11800 version 6

advertisement
NZQA Expiring unit standard
11800 version 6
Page 1 of 3
Title
Carry out calculations in the sailmaking industry
Level
3
Credits
4
Purpose
This unit standard is for people who work in the sailmaking or
allied industries. People credited with this unit standard are
able to: measure and calculate metric and imperial units;
calculate approximations and estimations; and calculate scales.
Classification
Outdoor Fabric Products > Sailmaking
Available grade
Achieved
Explanatory notes
1
The following legislation, regulations and rules and subsequent amendments are
relevant to this unit standard and must be followed where applicable:
– Health and Safety in Employment Act, 1992;
– International or National Rating and/or Racing Class or Rules.
2
When the evidence requirements state company policy, this is deemed to be to the
same standard as the sail and material or design manufacturers' repair standards.
3
This unit standard covers both metric and imperial measurements.
Outcomes and evidence requirements
Outcome 1
Measure and calculate using metric and imperial units.
Evidence requirements
1.1
Measuring tapes and/or rules are identified and used according to company
policy.
1.2
Calculator used to carry out calculations is identified and used according to
company policy.
1.3
Length is measured for a distance of up to 40 meters and to the imperial
equivalent, according to company policy.
1.4
Mass (weight) is measured up to 100 kg to within 99% accuracy.
1.5
Temperature is measured to within 0.5 °C.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
11800 version 6
Page 2 of 3
1.6
Perimeters of squares and rectangles, with sides measured to the nearest
millimetre (mm) and equivalent imperial fraction, are calculated according to
design specification.
1.7
Areas of squares and rectangles are calculated according to design
specification.
1.8
Volumes of cuboids are calculated according to design specification.
Outcome 2
Calculate approximations and estimations.
Evidence requirements
2.1
Numbers are rounded to three decimal places, and to the imperial equivalent,
according to company policy.
2.2
Conversions from metric to imperial measurements are carried out according to
company policy.
Range
2.3
length, weight, volume, area.
Calculations are completed to the required level of accuracy according to the
design specifications.
Outcome 3
Calculate scales.
Evidence requirements
3.1
Scale drawings are identified and interpreted according to design specifications.
3.2
Scales are calculated according to design specifications.
3.3
Calculations are completed to the required level of accuracy according to the
design specifications.
This unit standard is expiring. Assessment against the standard must take place by
the last date for assessment set out below.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
11800 version 6
Page 3 of 3
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
25 September 1997
31 December 2016
Revision
2
14 November 2000
31 December 2016
Revision
3
16 October 2003
31 December 2016
Review
4
26 March 2007
31 December 2016
Rollover
5
19 November 2010
31 December 2016
Rollover
6
18 February 2016
31 December 2020
Consent and Moderation Requirements (CMR) reference
0014
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA, or
an inter-institutional body with delegated authority for quality assurance, before they can
report credits from assessment against unit standards or deliver courses of study leading
to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Consent requirements and an outline of the moderation system that applies to this
standard are outlined in the Conesnt and Moderation Requirements (CMR). The CMR
also includes useful information about special requirements for organisations wishing to
develop education and training programmes, such as minimum qualifications for tutors and
assessors, and special resource requirements.
NZ Motor Industry Training Organisation
(Incorporated)
SSB Code 101542
 New Zealand Qualifications Authority 2016
Download