 Automation Interface Module (AIM) Worksheet Communications Interface Module (CIM) Worksheet

advertisement
 Automation Interface Module (AIM) Worksheet
ü
 Communications Interface Module (CIM) Worksheet
Directions: Fill in section 1: Document the desired status and control points for each lighting panel. Please indicate the # of relays in each panel and
whether you would like to just check status or if you would also like to issue commands. If the panels have the same command and status requirements,
you may submit one sheet that has all applicable panels listed in the space provided at the bottom of this section. Fill in section 2 on one sheet only.
Section I
Relay
Check
Relay
Status
ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

















01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Issue Relay
Commands
ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü


ü
















Relay Outputs
If you wish to issue commands to
this relay as part of a command
group, please indicate group #
that this relay belongs to.
Local Contact Inputs
Notes
Input
Check
Input
Status
Notes
32
ü

ü

ü

ü





























Analog
Input
Check
Input
On/Off
Status
Check Analog Reading








01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
01
02
03
04
Occ Sensor
Photocell
Occ Sensor
Lighting Control Relay Panel Information
Panel Type
(1 type per sheet)
CKT
Panel Address
LCP1
LCP2
LCP3
LCP4
LCP5
Panel Location
Electrical Rm W
Electrical Rm E
Electrical Rm 1A
Electrical Rm N
Electrical Rm S
Panel Address
Panel Location
LCP6
Electrical Rm 2C
Panel Address
Panel Location
Panel Address
Panel
Location
Page
Page 5
Section II
Setup Information (Fill in on one sheet only and choose only one protocol)
ü Automation Interface Module (AIM)

 Communications Interface Module (CIM)
What Protocol will you be using? (circle one)
BACnet
BACnet
BACnet


willbe
beusing
usingBACnet
BACnetover
overIP
IP
üI Iwill
Default
DefaultGateway
GatewayIPIPAddress
Address
BACnet
DesiredNetwork
BACnetNumber
Device Object Instance ID#
Desired BACnet Device Object Instance ID#
LON
(Please
(Pleaseprovide
providethe
thefollowing
followinginformation
informationfor
forproper
proper
configuration.
configuration. Please
Pleasenote
note––the
theMAC
MACaddress
address
information
informationofofthe
theunit
unitwill
willbe
beprovided
providedon
onthe
thefinal
final
mapping
mappingtable
tableonce
oncethe
theunit
unitisisconfigured)
configured)
10.429.92.7
255.255.255.1
Subnet
SubnetMask
Mask
Modbus

I Iwill
willbe
beusing
usingBACnet
BACnetover
overEthernet
Ethernet
(Please
(Pleaseprovide
providethe
thefollowing
followinginformation
informationfor
forproper
proper
configuration)
configuration)
IPIPAddress
Address
COMPLETE
ONLY ONE
SECTION
BELOW
BACnet
BACnetNetwork
NetworkNumber
Number
10.429.92.6
60001
6
Desired
DesiredBACnet
BACnetDevice
DeviceObject
ObjectInstance
InstanceID#
ID#
 I will be using BACnet over ARC156
following
information
for proper
 I (Please
will be provide
using the
BACnet
over
ARC156
 I will be using BACnet over MS/TP
following
information
 I(Please
will beprovide
usingthe
BACnet
over
MS/TPfor proper
configuration)
(Please
provide the following information for proper
configuration)
Desired ARCnet Address
configuration)
(Please
provide the following information for proper
configuration)
Desired MS/TP Address
Desired
BACnetARCnet
NetworkAddress
Number
Desired
Address
BACnetMS/TP
Network
Number
BACnet
DesiredNetwork
BACnet Number
Device Object Instance ID#
BACnet
DesiredNetwork
BACnet Number
Device Object Instance ID#
Desired BACnet Device Object Instance ID#
Desired
Device
What isBACnet
the desired
baudObject
rate Instance ID#
What
Whatisisthe
thedesired
desiredbaud
Max rate
Master setting? (default is 127)
What is the desired Max Master setting? (default is 127)
Modbus
Choose Protocol Configuration: Baud Rate Data Bits Expected
Choose Protocol Configuration


RTU
ACCII
Baud Rate






1200
2400
4800
Choose Com Type
RS232
2wire RS485
4 wire RE485/422



9600
19200
38400
Parity
Indicate Desired Slave Address
Odd
Even
None



N2
What N2 slave address should be assigned to the AIM?
(This address must be different from any other N2 device on the N2 BUS.)
LON
No additional Information needed
Data Bits Expected
8
7


Stop Bits Expected
1
2


N2
Download