Room Controller - Classroom
w/Daylight Dimming and Receptacle Control
Half Lights
Full Lights
Raise
Lower
All Off
Summary
A well designed control system requires the consideration of energy codes, the building occupants’ use patterns and the type of lighting that is used in each room.
Careful design and the use of strategies such as daylighting, ambient task lighting, and advanced technologies can achieve even greater energy efficiency and higher
quality lighting.
RC3DE
The Room Controller QuicKit is shipped preconfigured to work out-of-the-box minimizing installation and setup time, while ensuring maximum energy savings.
Using this design guide to specify your room with a Room Controller QuicKit catalog number will guarantee that after installation the lighting control system will
work immediately as defined on this application guide.
Room Controller Sample room layout (30’ x 30’)
Room Controller QuicKit
Half Lights
Half Lights
Full Lights
Full Lights
Half
Lights
Raise
Raise
Full Lights
Lower
Lower
Raise
All
Off
All Off
Lower
Product Legend
All Off
RCQK-CR3E-ES1-TS1-C1-D1-P-W
RC3DE
Half Lights
Full Lights
Load 3
General On
AV Mode
Whiteboard
Quiet Time
Normal
Power
Connection
RC-6TSB-TS2-*
(Pre-engraved Wallstation)
Raise
Lower
RC3DE
RC3DE
All Off
Half Lights
Full Lights
Raise
Entry
Lower
Lighting
All Off
Half Lights
All Off
Full Lights
Raise
Raise
Lower
Lower
RC3DE
All Off
Load 2
Load 2
Load 2
Dimmer 1
Dimmer 2
Dimmer 3
RC3DE
(3 Relay +
3 Dimmer
+ 1 Emergency
Relay)
RC3DE
Half Lights
Full Lights
Half Lights
Raise
Full Lights
Lower
All Off
Raise
Lower
RC3DE
All Off
RC3DE
Half Lights
Full Lights
Raise
Lower
All Off
General On
RC3DE
RC3DE
RC3D
Off
Load 2
Load 2
Load 2
Dimmer 1
Dimmer 2
Dimmer 3
DSRC-FMOIR
(Multi-zone
Daylight Sensor)
All Off
Reading
2
SLEEP
Dimmer
3
3
5
6
8
Qty1: OAC-DT-2000
Ceiling Mount vacancy sensor
Qty1: GGRJ45-10-G
Quickconnect cable 10’
9
0
MUTE
OPTION
2
Entry1
Lighting
Dimmer 3
Load 1
VOLUME
cc
1
4
7
3
ALL
ON/OFF
All Off
RC3D
Emergency UL924 Load
Dimmer 2
TV
CHANNEL
PREV
Dimmer 3
Load 1
All Off
Load 1
Daylighting Zone 3
Dimmer
1
Dimmer 2
Daylighting Zone 2
Dimmer 1
Load 1
Dimmer 2
Qty1: DSRC-FMOIR
Daylight Sensor
Qty1: SPRC-R-20-120
Receptacle Control
Exam
Dimmer 1
Qty1: RC-6TSB-TS1-W
(General, Whiteboard, Quiet Time, A/V Mode, Raise, LoweR)
Qty1: OCC-RJ45
Occupancy sensor RJ45 connector
Entry
Lighting
OCC-RJ45
(Connection to any
Greengate Sensor)
Load 1
Qty1: RC-2TLB-ES1-W
(Entry, All Off)
RC3DE
General
Load 1
Daylighting Zone 1
RC-2TLB-ES1-*
(Pre-engraved
Wallstation)
OAC-DT-2000
(Ceiling Dual
Tech, 2000 sq. ft.)
Qty1: RC3DE
3 relay + 3 dimmer + 1 emergency relay
Qty3: GGRJ45-25-G
Quickconnect cable 25’
Qty1: GGRJ45-50-G
Quickconnect cable 50’
General
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
RC3D
Single box packaging with wiring detail
and installation
Entry
LightingGeneral
Exam
Entry
LightingReading
All Off
All Off
All Off
Recessed Fixture
Line Voltage
to J-Box
SPRC-R-20-120
(20A Receptacle Control)
TV
CHANNEL
VOLUME
cc
General
1
2
3
Entry
4
5
Lighting
Exam
6
Reading
7
All Off
8
9
0
PREV
MUTE
All Off 2
SLEEP
OPTION
1
3
ALL
ON/OFF
For guaranteed compatibility refer to preferred Cooper
lighting fixture information below.
Entry
Lighting
All Off
TV
CHANNEL
VOLUME
cc
1
2
3
Entry
5 6
Lighting
8 9
4
7
0
PREV
SLEEP
MUTE
OPTION
2
1
3
All Off
ALL
ON/OFF
Control sequence
RC3D
RC3D
Entry
Lighting
• Manual On/Automatic Off or Automatic On (50%)/Automatic Off
1. Toggle Load 2
• Front/Back/Whiteboard control of Classroom
2. Toggle Load 3
Entry
General
All Off
Lighting
Whiteboard
Quiet Time •
All A/V
OffMode
Raise
Lower
General
Whiteboard
Quiet Time •
A/V Mode
General
RC3D
Lower
All Off
• High-end trim/tuning to define target light levels
Whiteboard
Quiet Time •
• Automatic multi-zone daylight dimming out-of-the-box
• Receptacle control based on occupancy
UL924
• Emergency
UL924 UL 924 control (tracks with relay 1)
Entry
Lighting
Raise
A/V Mode
3. Disable Occ Sensor for 1 hr
RC3D
4.RC3D
Set Dimmers to 20%
Entry
1. Toggle Load 1
2. Load 1, 2, 3 Off
All Off
General
Exam
General
Reading
Exam
All Off
Raise
Lower
Reading
All Off
5. Raise Dimmers 5%
6.RC3D
Lower Dimmers 5%
RC3D
UL924
TV
CHANNEL
VOLUME
cc
1
TV
2 3
CHANNEL
VOLUME
cc
General
5 6
4
• Automatic Demand Response 10%-40% reduction based on input
71 Exam
82 93
4
0
5 6
Reading
PREV
7
RC-6TSB-TS1
MUTE
8
2
SLEEP
9
OPTION
All Off
1
RC-2TLB-ES1
3
0
PREV
MUTE
ALL
ON/OFF
SLEEP
OPTION
2
1
3
ALL
ON/OFF
RC3D
General
Exam
Reading
All Off
General
Exam
Integrated capabilities
Reading
All Off
TV
CHANNEL
VOLUME
cc
1
2
4
3
5
7
6
8
9
0
PREV
SLEEP
Cooper Lighting Guaranteed Compatible Fixtures
MUTE
OPTION
2
1
3
ALL
ON/OFF
General
TV
CHANNEL
VOLUME
Exam cc
1
Reading
General 2 3
General
4
6
All Off 5
Whiteboard
7 Exam
8
9
General
QuietReading
Time •
0
PREV
MUTE
Whiteboard
A/V Mode
All Off
SLEEP
CHANNEL
A/V Mode
Lower
1
Raise
4
2
6
8
9
0
PREV
SLEEP
MUTE
OPTION
2
1
3
ALL
ON/OFF
All Off
1
4
VOLUME
2
1
3
TV
6
cc
9
5
CHANNEL
7
8
01
PREV
SLEEP
MUTE
Room Controller Classroom Lighting Layouts
VOLUME
2
3
General
4
5 6
2
Whiteboard
7 38 9
OPTION
ALL
ON/OFF
Quiet 0
Time •
PREV
MUTE
SLEEP
OPTION
2
A/V Mode
1
3
Raise
ALL
ON/OFF
Lower
Manual
Control
Receptacle
Control
Emergency
Integration
Demand
Response
General
CHANNEL
TV
VOLUME
cc
Whiteboard
1
2
3
Quiet Time
•
4
5
6
7
A/V Mode
8
9
Raise
0
PREV
SLEEP
2
Lower 1
General
MUTE
OPTION
3
ALL
ON/OFF
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
General
www.coopercontrol.com
Whiteboard
Quiet Time •
General
A/V Mode
Whiteboard
Raise
Quiet Time •
Lower
A/V Mode
Raise
Lower
1
Room Controller Classroom Lighting Layouts
Corelite LFL
Exam
cc
Daylighting
Control
Corelite LED
General
Reading
TV
CHANNEL
Occupancy/Vacancy
Sensing
Room Controller Classroom Lighting Layouts
3
5
Lower
7
UL924
Room Controller Classroom Lighting Layouts
Metalux LFL
VOLUME
cc
ALL
ON/OFF
UL924
Metalux LED
OPTION
2
TV
1
Quiet
Time
3•
Raise
UL924
General
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
Refer to these Cooper Lighting data sheets for lighting layouts and illuminance
value information.
Room Controller - Classroom
w/Daylight Dimming and Receptacle Control
Room Controller and Smart Devices use Click & Go technology
The RC3DE will automatically recognize any smart device connected with the quick connect cable (provided) and start working immediately upon power up with
no programming required. The RC3DE defaults to Manual On/Automatic Off vacancy sensor mode for maximum energy savings. Entry wallstations will provice On/
Off control of the Yellow load. Teacher stations provide On/Off control of the Red and Purple loads as well as manual Raise/Lower of all dimmers.
The daylight sensor will automatically provide multi-zone daylight dimming in the space. (Remote adjustments can be made later.)
*Refer to Room Controller website for more information on other integral no programming required benefits like Demand Response, Solatube Control, Egress
Control, BMS Output, Alert Mode, Emergency Lighting Control, and Slider Stations.
EMERGENCY NEUTRAL
YELLOW
Emergency Power OUT
WHT/ORG or WHT/BLK
Neutral
BLACK - Hot
(120/277 VAC)
Emergency Lighting
Load
(Tracks with normal
lighting YELLOW load)
YELLOW
Lighting Load (1)
RED
Lighting Load (2)
PURPLE
Lighting Load (3)
BLUE - Relay In
(120/277 VAC)
BLUE - Emergency Power In
(120/277 VAC)
Requires 0-10V
dimming ballasts
Violet - Dimmer 1
Gray - Dimmer 1
Violet - Dimmer 2
Gray - Dimmer 2
Emergency Note:
Emergency load tracks with normal lighting
YELLOW load for On/OFF. If dimming it will be
adjusted with the dimming zone it is connected to.
Upon loss of normal power to the RC3DE, the
emergency load will be forced On and full bright to
100%.
Violet - Dimmer 3
Gray - Dimmer 3
0-10V Dimming Zone Note:
The 0-10V dimming zones within the
Room Controller can be wired and
controlled independent of the connected
loads. This allows a each load to have a
dedicated 0-10V dimming zone or a single
load to have up to three 0-10V dimming zones.
In room ladderless testing is done by pressing the
"All Off" button four times, within 3 seconds.
The RC3DE is UL 924 listed.
Receptacle Control:
20Amp 120 VAC receptacle control immediately works
upon power up and connection to the Room Controller.
Receptacle turns On by button press or occupancy and
Off when space is vacant.
QuickConnect coupler
(GGRC-COUPLER)
Adjustable daylight
sensor dome
Daylight sensor
(DSRC-FMOIR)
*Immediately provides multi-zone
daylight dimming upon powerup
Allows connection to
any Greengate
Occupancy/Vacancy
Sensor
(OCC-RJ45)
120V receptacle
circuit
SPRC-R-20-120
20A Receptacle Control
Button 1: Toggle Load (1)
Button 2: Load (1),(2),(3) Off
Dual Technology
Ceiling
Occupancy/Vacancy Sensor
(OAC-DT-2000)
Quick connect cables are
pre-terminated and included
in the Room Controller
QuicKit and measured to fit
typical room layouts
Entry
Lighting
General
Whiteboard
Quiet Time
All Off
A/V Mode
Connect up to four
wallstations per Room
Controller
RC-2TLB-EC1-*
Entry Station
Raise
Lower
RC-6TSB-TS1-*
Teacher Station
*Defaults to vacancy sensor mode
Manual On/Automatic Off (all loads)
Button 1: Toggle Load (2)
for maximum energy savings
Button 2: Toggle Load (3)
Button 3: Disable Occupancy Sensor for 1hr.
Button 4: Toggle dimmers between 20% and daylight level
Button 5: Press and hold increase lighting 5%
Button 6: Press and hold decrease lighting 5%
Cooper Controls
203 Cooper Circle
Peachtree City,
GA 30269. USA
Tel: +1-800-553-3879
Fax: +1-800-954-7016
Email: controls@cooperindustries.com
Website: www.coopercontrol.com
Room Controller - RC3DE
Three Relay + Three Dimmers Wiring Diagram + One Emergency Relay
Drawing Name:
RC3DE-ClassroomReceptacle.dwg
www.coopercontrol.com
2
Drawing Date:
1/10/2013
Room Controller - Classroom
w/Daylight Dimming and Receptacle Control
Mounting The Room Controller
The Room Controller mounts above the ceiling in the space it is controlling, typically above the door to the room. The Room Controller include breakouts for direct
conduit connection limiting the need for additional junction boxes. Mount the Room Controller using the keyhole slots at the top and secure to the wall using the
holes at the bottom of the Room Controller.
Connect conduit to the line voltage breakout connections and connect the line and load wires. Connect low voltage cables either through the low voltage breakout
openings or by connecting low voltage conduit to the breakouts on the low voltage side of the Room Controller.
Sample Placement Diagram
Daylight Sensor Ceiling Location
(for example purposes only)
1. Mount the daylight sensor one to two times the window height from the window wall.
2. Position the sensor so its arrow is pointed toward
the nearest window.
3. Ensure the daylight sensor is not obstructed or
looking directly at electric light.
4. For narrow spaces mount the daylight sensor near
the window facing into the space.
Sample Placement Diagram
(for example purposes only)
Room Controller
(above entry door)
Additional
Wallstation
General On
AV Mode
Whiteboard
Quiet Time
Raise
Lower
General On
Off
Entry
Wallstation
Window
Daylight
Sensor
60°
Ceiling Mount
Occupancy Sensor
Area viewed by
daylight sensor
Occupancy sensor Coverage Diagram (OAC-DT-2000)
Wiring Diagram
SPRC-R-20-120
Room Controller
Normal Power
(20A Receptacle Control)
(Above Entry Door)
(Line In & Load Out)
RC3DE
20 ft
(6.096m)
16 ft
(4.87 m)
12 ft
(3.65 m)
Line Voltage
to J-Box
0
Line Voltage
to receptacles
(low voltage, class 2)
OCC-RJ45
Emergency Power
(Line In & Load Out)
12 ft
(3.65 m)
DSRC-FMOIR
RC3DE model only
0-10V Dimmer Wiring
(Dimming Models Only)
16 ft
(4.87 m)
20 ft
(6.096m)
8.5 ft
(2.59 m)
(Multi-zone
daylight sensor)
(Any Greengate
Occupancy Sensor)
3 ft
(0.91)
0
Wallstation Wallstation
(Entry)
32 ft
(9.75 m)
(Additional)
Half Lights
Half Lights
Full Lights
Full Lights
Raise
Raise
Lower
Lower
All Off
All Off
23 ft
15 ft
(7.01 m) (4.57 m)
Minor Motion, IR
Major Motion, IR
Minor Motion, Ultrasonic
Major Motion, Ultrasonic
10 ft
(3 m)
5 ft
(1.52 m)
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
0
5 ft
(1.52 m)
10 ft
(3 m)
23 ft
15 ft
(4.57 m) (7.01 m)
32 ft
(9.75 m)
Ceiling Height = 8.5 ft.
The NEMA WD 7 Guide and robotic
method were utilized to verify
coverage patterns.
Connections
Room Controller and Smart Devices
use Click & Go Connections
Room Controller 0-10V Dimming Connections
Dimmer 1: Near the Window
Dimmer 2: Middle of Room
Dimmer 3: Far from Window
-
Dimmer 3
+
-
Dimmer 2
+
-
Dimmer 1
+
The daylight sensor will automatically provide multi-zone
dimming based on this wiring configuration
0-10V Dimming
1
0-10V Gray (-)
0-10V Violet (+)
www.coopercontrol.com
3
2
5
34
6
1. Wallstations (up to four)
2. Slider Station Connection (one)
3. Occupancy Sensors (up to two)
4. Daylight Sensor (one)
5. Receptacle Control or BMS Output
6. Switchpack (controlled with Load 1 for
alternate voltage)
Room Controller - Classroom
w/Daylight Dimming and Receptacle Control
Ordering
RCQK
-
CR3E
-
ES1
Room Controller
-
TS1
-
C1
-
D1
-
P
-
Daylight
Office Stations (Choose up to 4)
W
Station Color
D1 - Multi-zone Daylight Sensor
ES1 - Entry, All Off (2 Large Buttons)
Entry Station (Choose 1)
DH - Multi-zone Daylight Sensor w/
TS1 - General, Whiteboard, Quiet Time,
ES1 - Entry, All Off (2 Large Buttons)
Handheld Remote
A/V Mode, Raise,Lower † (6 Small Buttons)
Options
TS5 - Entry, General, Whiteboard,
TS2 - General, Whiteboard, Quiet Time, Raise,
P - Plug Load
Types of Space
All Off (4 Small Buttons)
Lower, All Off † (6 Small Buttons)
B - BMS/Egress
and Control
Occupancy Sensor
TS3 - General, Whiteboard, Quiet Time, A/V Mode, All Off †
CR - Classroom Switching (RC3)
C1 - Ceiling DT 2000 sq. ft.
(5 Small Buttons)
CR2 - Classroom 2 Zone Dimming (RC3D2)
C2 - Ceiling PIR 1500 sq. ft.
TS4 - General, Whiteboard, A/V Mode, Raise, Lower, All Off †
CR3 - Classroom 3 Zone Dimming (RC3D)
C3 - Ceiling DT 1000 sq. ft.
(6 Small Buttons)
CR3E - Classroom 3 Zone Dimming and
W1 - Wall Corner DT
TS5 - Entry, General, Whiteboard, All Off (4 Small Buttons)
and Emergency Relay (RC3DE)
W2 - Wall Corner PIR
TS6 - Entry, General, Whiteboard, Raise, Lower, All Off †
W3 - Hallway PIR
(6 Small Buttons)
QuicKit
W - White
G - Gray
V - Ivory
B - Black
TS7 - Row 1, Row 2, Row 3, Raise, Lower, All Off †
(6 Small Buttons)
TS8 - Uplights, Downlights, Accent, Raise, Lower, All Off †
*Catalog number automatically includes low voltage
(6 Small Buttons)
connection cable, wallplates and connectors based on room
SS1 - Slider Station ††
type and configuration.
Pre-defined Wallstation Model numbers
Entry
All Off
General
General
General
General
Entry
Entry
Row 1
Uplights
Whiteboard
Whiteboard
Whiteboard
Whiteboard
General
General
Row 2
Downlights
Quiet Time •
Quiet Time •
Quiet Time
A/V Mode
Whiteboard
Whiteboard
Row 3
Accent
A/V Mode
Raise
All Off
Raise
Raise
Raise
Lower
Lower
Lower
Lower
All Off
All Off
All Off
All Off
Raise
A/V Mode
Lower
Raise
All Off
Lower
RC-2TLB-ES1
All Off
RC-6TSB-TS1
RC-6tsb-TS2
RC-5TSB-TS3
RC-6tsb-TS4
RC-4tsb-TS5
RC-6Tsb-TS6
RC-6tsb-TS7
RC-6tsb-TS8
*For site specific engraving, please see the Room Controller Wallstation custom engraving form on the Cooper Controls website
Applications
Classroom Application Button Functionality
Function
(Unless a target level is indicated, the dimmer output will default to
daylight sensor control)
Program
No.
Button Text
Control
Type
1
Entry
Row 1
Uplights
Toggle
Load 1 (yellow) ON and OFF
Solatube Open (RC3DE only)
2
General
Row 2
Downlights
Toggle
Load 2 (red) ON and OFF
3
Whiteboard
Row 3
Toggle
Load 3 (purple) ON and OFF
4
A/V Mode
Toggle
Toggles between A/V Mode and Normal Mode relay will stay in their previous
configuration. Dimmers will be reduced to maintain light levels at 20%
5
Quiet Time
Toggle
Disables occupancy sesnors and wallstation timers for 60 minutes. Toggle
allows for re-enabling of Normal Mode prior to the timer expiring
6
Raise
Raise
Raise All Dimmers
7
Lower
Lower
Lower All Dimmers
8
All Off
Slider
†
†
Load 1 (yellow) OFF, Load 2 (red) OFF, Load 3 (purple) OFF
Solatube Closed (RC3DE only)
Slider
††
Raise and Lower All Dimmers
Catalog #
Type
Project
†
These dimming wallstations can only be used with dimming Room Controllers (RC3D, RC3D2, RC3DE)
†† Slider stations can not be used if a wallstation with Raise/Lower buttons are used
Comments
Prepared by
www.coopercontrol.com
4
ACC130080
Date