Room Controller - Classroom
w/Daylight Dimming, Receptacle Control and Suspended Fixtures
Summary
A well designed control system requires the consideration of energy codes, the building occupants’ use patterns and the type of lighting that is used in each room.
Careful design and the use of strategies such as daylighting, ambient task lighting, and advanced technologies can achieve even greater energy efficiency and higher
quality lighting.
The Room Controller QuicKit is shipped preconfigured to work out-of-the-box minimizing installation and setup time, while ensuring maximum energy savings.
Using this design guide to specify your room with a Room Controller QuicKit catalog number will guarantee that after installation the lighting control system will
work immediately as defined on this application guide.
Half Lights
Full Lights
Raise
Lower
All Off
Room Controller Sample room layout (30ʹ x 30ʹ)
Room Controller QuicKit
Half Lights
Half Lights
Lights
Full
Full Lights
Half
Lights
Raise
Raise
Full Lights
Lower
Lower
Raise
All Off
All
Off
Lower
All Off
RCQK-CR3E-ES1-TS1-W1-D1-P-W
RC3DE
RC3DE
Half Lights
Full Lights
Load 3
General On
Raise
RC3DE
RC3DE
Lower
All Off
AV Mode
Normal Power
Connection
Whiteboard
Quiet Time
Raise
Lower
RC-6TSB-TS2-*
(Pre-engraved Wallstation)
Full Lights
FullLower
Lights
Entry
Lighting
Raise
All Off
AllFull
Off Lights
All
Off
Raise
Lower
RC3DE
All Off
Load 1
RC3DE
(3 Relay +
3 Dimmer + 1
Emergency Relay)
RC3DE
Half Lights
Full Lights
Half Lights
Raise
Full Lights
Lower
Raise
All Off
Lower
RC3DE
RC3DE
All Off
RC3DE
General On
Off
RC3DE
RC3DE
RC3D
DSRC-FMOIR
(Multi-zone
Daylight Sensor)
RC-2TLB-ES1-*
(Pre-engraved
Wallstation)
Qty1: RC-2TLB-ES1-W
(Entry, All Off)
Qty1: RC-6TSB-TS1-W
(General, Whiteboard, Quiet Time, A/V Mode, Raise, LoweR)
Qty1: DSRC-FMOIR
Daylight Sensor
Qty1: OAWC-DT-120W
Wall Corner Mount vacancy sensor
Qty1: OCC-RJ45
Occupancy sensor RJ45 connector
Qty1: SPRC-R-20-120
Receptacle Control
General
Exam
Reading
Daylighting Zone 3
Daylighting Zone 2
All Off
Daylighting Zone 1
Qty1: RC3DE
3 relay + 3 dimmer + 1 emergency relay
Half Lights
Half Lights
Raise
Half Lights
Lower
EM Load
Product Legend
TV
CHANNEL
VOLUME
cc
1
2
3
4
5
6
7
8
9
0
PREV
SLEEP
MUTE
OPTION
2
Entry
1
Lighting
Qty1: GGRJ45-10-G
Quickconnect cable 10’
3
ALL
ON/OFF
All Off
Qty3: GGRJ45-25-G
Quickconnect cable 25’
Qty1: GGRJ45-50-G
Quickconnect cable 50’
Entry
Lighting
All Off
OCC-RJ45
(Connection to any
Greengate Sensor)
General
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
RC3D
Single box packaging with wiring detail
and installation
Entry
Lighting
Entry
Lighting
All Off
All Off
OAWC-DT-120W
(Wall Corner
Dual Tech)
SPRC-R-20-120
(20A Receptacle Control)
suspended Fixture
Line Voltage
to J-Box
General
Exam
Entry
Lighting
Reading
All Off
All Off
RC3D
For guaranteed compatibility refer to preferred Cooper
lighting fixture information below.
Entry
Lighting
Entry
Lighting
All Off
TV
CHANNEL
VOLUME
cc
1
2 3
All Off
4Entry
5 6
7
8 9
Lighting
0
PREV
SLEEP
MUTE
OPTION
2
1
3
All Off
ALL
ON/OFF
Control sequence
RC3D
RC3D
Entry
Lighting
• Manual On/Automatic Off or Automatic On (50%)/Automatic Off
• High-end trim/tuning to define target light levels
1. Toggle Load 2
Entry
Lighting
All Off
All Off
2. Toggle Load 3
General
General
Whiteboard
Exam
Quiet Time •
Reading
A/V Mode
General
• Automatic multi-zone daylight dimming out-of-the-box
Raise
All Off
RC3D
Lower
3. Disable Occ Sensor for 1 hr
Whiteboard
Quiet Time •
• Receptacle control based on occupancy
A/V Mode
RC3D
RC3D
4. Set Dimmers to 20%
RC3D
2. Load 1, 2, 3 Off
All Off
Exam
TV
CHANNEL
VOLUME
cc
All Off
Exam
Raise
1. Toggle Load 1
General
Reading
General
• Emergency UL 924 control (tracks with relay 1)
UL924
• Automatic
UL924 Demand Response 10%-40% reduction based on input
Entry
1
Reading
All Off
2
4
3
5
7
6
8
9
5. Raise Dimmers 5%
0
PREV
SLEEP
1
MUTE
OPTION
2
3
ALL
ON/OFF
Lower
6. Lower Dimmers 5%
RC3D
RC3D
UL924
TV
CHANNEL
VOLUME
cc
1
CHANNEL
4
7
1
PREV
4
RC-6TSB-TS1
2
TV
5
cc
8
3
VOLUME
6
General
9
2 3
Exam
0
5
28
MUTE
6
Reading
SLEEP
7
1
OPTION
9
3
All Off
0
ALL
ON/OFF
PREV
SLEEP
RC-2TLB-EC1
MUTE
OPTION
2
1
3
ALL
ON/OFF
General
Exam
Reading
General
All Off
Exam
General
Reading
Whiteboard
All Off
Quiet Time •
General
A/V Mode
Exam
Integrated capabilities
Raise
Reading
All Lower
Off
TV
CHANNEL
VOLUME
cc
1
2
4
3
5
7
6
8
0
PREV
SLEEP
9
Cooper Lighting Guaranteed Compatible Fixtures
MUTE
OPTION
2
1
3
ALL
ON/OFF
CHANNEL
TV
General
VOLUME
cc
Exam
General
1
2
3
General
TV
Reading
Whiteboard
CHANNEL
4
5
6
VOLUME
cc
Exam
7Off 8 9
All
Quiet
Time •
General
1
PREV
2 3
Reading
0
MUTE
Whiteboard
A/V Mode
4
SLEEP
5
6
ALL
ON/OFF
SLEEP
UL924
OPTION
3
6
ALL
ON/OFF
Lower
7
8
0
PREV
SLEEP
1
2
9
MUTE
OPTION
3
ALL
ON/OFF
TV
VOLUME
cc
1
4
7
PREV
SLEEP
1
2
CHANNEL
5
81
TV
3
92
3
MUTE
OPTION
2
A/V
1 Mode
3
ALL
ON/OFF
Lower
Receptacle
Control
Emergency
Integration
Demand
Response
General
Whiteboard
Quiet Time •
General
A/V Mode
Whiteboard
Raise
Quiet
Time •
Lower
A/V
Mode
General
Raise
Whiteboard
Lower
Quiet Time •
A/V Mode
Raise
Lower
General
www.coopercontrol.com
Whiteboard
General
Quiet Time •
Whiteboard
A/V Mode
Quiet Time •
Raise
A/V Mode
Lower
Raise
Lower
1
Room Controller Classroom Lighting Layouts
6
OPTION
PREV
Raise
Manual
Control
Room Controller Classroom Lighting Layouts
Neoray LFL
3
5
MUTE
7
8 9
Whiteboard
2
Quiet 0
Time •
SLEEP
Daylighting
Control
Neoray LED
VOLUME
cc
6
General
04
ALL
ON/OFF
Occupancy/Vacancy
Sensing
Room Controller Classroom Lighting Layouts
VOLUME
MUTE
2
21
1Raise 3
4
5
CHANNEL
Room Controller Classroom Lighting Layouts
Corelite LFL
OPTION
CHANNEL
0 cc
Lower
A/V
Mode
UL924
Corelite LED
All Off
2
7Quiet
Raise
9
1 8Time
TV
3•
PREV
UL924
Refer to these Cooper Lighting data sheets for lighting layouts and illuminance
value information.
Room Controller - Classroom
w/Daylight Dimming, Receptacle Control and Suspended Fixtures
Room Controller and Smart Devices use Click & Go technology
The RC3DE will automatically recognize any smart device connected with the quick connect cable (provided) and start working immediately upon power up with no
programming required. The RC3DE defaults to Manual On/Automatic Off vacancy sensor mode for maximum energy savings. Entry wallstations will provide On/Off
control of the Yellow load. Teacher stations provide On/Off control of the Red and Purple loads as well as manual Raise/Lower of all dimmers.
The daylight sensor will automatically provide multi-zone daylight dimming in the space. (Remote adjustments can be made later.)
*Refer to Room Controller website for more information on other integral no programming required benefits like Demand Response, Solatube Control, Egress
Control, BMS Output, Alert Mode, Emergency Lighting Control, and Slider Stations.
EMERGENCY NEUTRAL
YELLOW
Emergency Power OUT
WHT/ORG or WHT/BLK
Neutral
BLACK - Hot
(120/277 VAC)
Emergency Lighting Load
(Tracks with normal
lighting YELLOW load)
YELLOW
Lighting Load (1)
RED
Lighting Load (2)
PURPLE
Lighting Load (3)
BLUE - Relay In
(120/277 VAC)
BLUE - Emergency Power In
(120/277 VAC)
Requires 0-10V
dimming ballasts
Violet - Dimmer 1
Gray - Dimmer 1
Violet - Dimmer 2
Gray - Dimmer 2
Emergency Note:
Emergency load tracks with normal lighting
YELLOW load for On/OFF. If dimming it will be
adjusted with the dimming zone it is connected to.
Upon loss of normal power to the RC3DE, the
emergency load will be forced On and full bright to
100%.
Violet - Dimmer 3
Gray - Dimmer 3
0-10V Dimming Zone Note:
The 0-10V dimming zones within the
Room Controller can be wired and
controlled independent of the connected
loads. This allows a each load to have a
dedicated 0-10V dimming zone or a single
load to have up to three 0-10V dimming zones.
In room ladderless testing is done by pressing the
"All Off" button four times, within 3 seconds.
The RC3DE is UL 924 listed.
Receptacle Control:
20Amp 120 VAC receptacle control immediately works
upon power up and connection to the Room Controller.
Receptacle turns On by button press or occupancy and
Off when space is vacant.
QuickConnect coupler
(GGRC-COUPLER)
Adjustable daylight
sensor dome
Daylight sensor
(DSRC-FMOIR)
*Immediately provides multi-zone
daylight dimming upon powerup
Allows connection to
any Greengate
Occupancy/Vacancy
Sensor
(OCC-RJ45)
120V receptacle
circuit
SPRC-R-20-120
20A Receptacle Control
Button 1: Toggle Load (1)
Button 2: Load (1),(2),(3) Off
Quick connect cables are
pre-terminated and included
in the Room Controller
QuicKit and measured to fit
typical room layouts
Entry
Lighting
General
Whiteboard
Quiet Time
All Off
A/V Mode
Connect up to four
wallstations per Room
Controller
RC-2TLB-EC1-*
Entry Station
Raise
Lower
RC-6TSB-TS1-*
Teacher Station
Dual Technology
Wall Corner
Occupancy/Vacancy Sensor
(OAWC-DT-120W)
*Defaults to vacancy sensor mode
Manual On/Automatic Off (all loads)
for maximum energy savings
Button 1: Toggle Load (2)
Button 2: Toggle Load (3)
Button 3: Disable Occupancy Sensor for 1hr.
Button 4: Toggle dimmers between 20% and daylight level
Button 5: Press and hold increase lighting 5%
Button 6: Press and hold decrease lighting 5%
Cooper Controls
203 Cooper Circle
Peachtree City,
GA 30269. USA
Tel: +1-800-553-3879
Fax: +1-800-954-7016
Email: controls@cooperindustries.com
Website: www.coopercontrol.com
Room Controller - RC3DE
Three Relay + Three Dimmers Wiring Diagram + One Emergency Relay
Drawing Name:
Drawing Date:
RC3DE-ClassroomReceptacleWC.dwg 1/10/2013
www.coopercontrol.com
2
Room Controller - Classroom
w/Daylight Dimming, Receptacle Control and Suspended Fixtures
Mounting The Room Controller
The Room Controller mounts above the ceiling in the space it is controlling, typically above the door to the room. The Room Controller include breakouts for direct
conduit connection limiting the need for additional junction boxes. Mount the Room Controller using the keyhole slots at the top and secure to the wall using the
holes at the bottom of the Room Controller.
Connect conduit to the line voltage breakout connections and connect the line and load wires. Connect low voltage cables either through the low voltage breakout
openings or by connecting low voltage conduit to the breakouts on the low voltage side of the Room Controller.
Sample Placement Diagram
Daylight Sensor Ceiling Location
(for example purposes only)
1. Mount the daylight sensor one to two times the
window height from the window wall.
2. Position the sensor so its arrow is pointed toward
the nearest window.
3. Ensure the daylight sensor is not obstructed or
looking directly at electric light.
4. For narrow spaces mount the daylight sensor near
the window facing into the space.
Sample Placement Diagram
(for example purposes only)
Room Controller
(above entry door)
Wall/Corner Mount
Occupancy Sensor
Additional
Wallstation
General On
AV Mode
Whiteboard
Quiet Time
Raise
Lower
Entry
Wallstation
General On
Off
Window
Daylight
Sensor
60°
Area viewed by
daylight sensor
Occupancy sensor Coverage Diagram (OAWC-DT-120W)
Wiring Diagram
24’ (7.3 mm)
Room Controller
Normal Power
(20A Receptacle Control)
(Above Entry Door)
(Line In & Load Out)
Line Voltage
to J-Box
Line Voltage
to receptacles
(low voltage, class 2)
RC3DE
20’ (6 mm)
SPRC-R-20-120
12’ (3.7 mm)
(Line In & Load Out)
0-10V Dimmer Wiring
(Dimming Models Only)
Major Motion, IR
Minor Motion, Ultrasonic
12’ (3.7 mm)
DSRC-FMOIR
RC3DE model only
Minor Motion, IR
8’ (2.4 mm)
0
8’ (2.4 mm)
OCC-RJ45
Emergency Power
Major Motion, Ultrasonic
(Multi-zone
daylight sensor)
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
(Any Greengate
Occupancy Sensor)
Wallstation Wallstation
(Entry)
The NEMA WD 7 Guide and robotic
method were utilized to verify
coverage patterns.
24’ (7.3 mm)
10 ft
(3 mm)
(Additional)
Half Lights
Half Lights
Full Lights
Full Lights
Raise
Raise
Lower
Lower
All Off
All Off
20’ (6 mm)
24 ft
6 ft
15 ft
(1.7 mm) (4.6 mm) (7.3 mm)
50 ft
(15.3 mm)
Connections
Room Controller and Smart Devices
use Click & Go Connections
Room Controller 0-10V Dimming Connections
Dimmer 1: Near the Window
Dimmer 2: Middle of Room
Dimmer 3: Far from Window
-
Dimmer 3
+
-
Dimmer 2
+
-
Dimmer 1
+
The daylight sensor will automatically provide
multi-zone dimming based on this wiring configuration
0-10V Dimming
1
0-10V Gray (-)
0-10V Violet (+)
www.coopercontrol.com
3
2
5
34
6
1.
2.
3.
4.
5.
6.
Wallstations (up to four)
Slider Station Connection (one)
Occupancy Sensors (up to two)
Daylight Sensor (one)
Receptacle Control or BMS Output
Switchpack (controlled with Load 1 for
alternate voltage)
Room Controller - Classroom
w/Daylight Dimming, Receptacle Control and Suspended Fixtures
Ordering
RCQK
-
CR3E
-
ES1
Room Controller
-
TS1
-
W1
-
D1
-
P
-
Daylight
Office Stations (Choose up to 4)
W
Station Color
D1 - Multi-zone Daylight Sensor
ES1 - Entry, All Off (2 Large Buttons)
Entry Station (Choose 1)
DH - Multi-zone Daylight Sensor w/
TS1 - General, Whiteboard, Quiet Time,
ES1 - Entry, All Off (2 Large Buttons)
Handheld Remote
A/V Mode, Raise, Lower † (6 Small Buttons)
Options
TS5 - Entry, General, Whiteboard,
TS2 - General, Whiteboard, Quiet Time, Raise,
P - Plug Load
Types of Space
All Off (4 Small Buttons)
Lower, All Off † (6 Small Buttons)
B - BMS/Egress
and Control
Occupancy Sensor
TS3 - General, Whiteboard, Quiet Time, A/V Mode, All Off †
CR - Classroom Switching (RC3)
C1 - Ceiling DT 2000 sq. ft.
(5 Small Buttons)
CR2 - Classroom 2 Zone Dimming (RC3D2)
C2 - Ceiling PIR 1500 sq. ft.
TS4 - General, Whiteboard, A/V Mode, Raise, Lower, All Off †
CR3 - Classroom 3 Zone Dimming (RC3D)
C3 - Ceiling DT 1000 sq. ft.
(6 Small Buttons)
CR3E - Classroom 3 Zone Dimming and
W1 - Wall Corner DT
TS5 - Entry, General, Whiteboard, All Off (4 Small Buttons)
and Emergency Relay (RC3DE)
W2 - Wall Corner PIR
TS6 - Entry, General, Whiteboard, Raise, Lower, All Off †
W3 - Hallway PIR
(6 Small Buttons)
QuicKit
W - White
G - Gray
V - Ivory
B - Black
TS7 - Row 1, Row 2, Row 3, Raise, Lower, All Off †
(6 Small Buttons)
TS8 - Uplights, Downlights, Accent, Raise, Lower, All Off †
*Catalog number automatically includes low voltage
(6 Small Buttons)
connection cable, wallplates and connectors based on room
SS1 - Slider Station ††
type and configuration.
Pre-defined Wallstation Model numbers
Entry
All Off
General
General
General
General
Entry
Entry
Row 1
Uplights
Whiteboard
Whiteboard
Whiteboard
Whiteboard
General
General
Row 2
Downlights
Quiet Time •
Quiet Time •
Quiet Time
A/V Mode
Whiteboard
Whiteboard
Row 3
Accent
A/V Mode
Raise
A/V Mode
Raise
All Off
Raise
Raise
Raise
Raise
Lower
All Off
Lower
Lower
Lower
Lower
All Off
All Off
All Off
All Off
All Off
Lower
RC-2TLB-ES1
RC-6TSB-TS1
RC-6tsb-TS2
RC-5TSB-TS3
RC-6tsb-TS4
RC-4tsb-TS5
RC-6Tsb-TS6
RC-6tsb-TS7
RC-6tsb-TS8
*For site specific engraving, please see the Room Controller Wallstation custom engraving form on the Cooper Controls website
Applications
Classroom Application Button Functionality
Function
(Unless a target level is indicated, the dimmer output will default to
daylight sensor control)
Program
No.
Button Text
Control
Type
1
Entry
Row 1
Uplights
Toggle
Load 1 (yellow) ON and OFF
Solatube Open (RC3DE only)
2
General
Row 2
Downlights
Toggle
Load 2 (red) ON and OFF
3
Whiteboard
Row 3
Toggle
Load 3 (purple) ON and OFF
4
A/V Mode
Toggle
Toggles between A/V Mode and Normal Mode relay will stay in their previous
configuration. Dimmers will be reduced to maintain light levels at 20%
5
Quiet Time
Toggle
Disables occupancy sesnors and wallstation timers for 60 minutes. Toggle
allows for re-enabling of Normal Mode prior to the timer expiring
6
Raise
Raise
Raise All Dimmers
7
Lower
Lower
Lower All Dimmers
8
All Off
Slider
†
†
Load 1 (yellow) OFF, Load 2 (red) OFF, Load 3 (purple) OFF
Solatube Closed (RC3DE only)
Slider
††
Raise and Lower All Dimmers
Catalog #
Type
Project
†
These dimming wallstations can only be used with dimming Room Controllers (RC3D, RC3D2, RC3DE)
††
Slider stations can not be used if a wallstation with
Raise/Lower buttons are used
Comments
Prepared by
www.coopercontrol.com
4
ACC130082
Date