Week 3 Assignments and Readings (September 29th – Oct 3rd)
APSC 100 Mod 1
D2L Homework
Week 4 readings Modeling/Argumentation and Root Finding/Debugging.
Week 4 pre-lecture quiz + pre-studio quiz due Monday October 5th at 10:30 AM.
Electrical safety quiz due October 23rd (instructions on D2L)
WHMIS quiz (this one is on Moodle)
Individual Report due October 16th [more information later]
APSC 100 Mod 2
Tutorial Lab #2 report due at start of week 4 lab period. Don’t forget to sign the
honesty statement on the hardcopy and upload your e-copy to D2L.
Complete pre-lab for Lab (see rotation sheet) in time for week 4 lab period
APSC 111
APSC 131
If you are doing Lab #4 you must complete the Chemistry Lab Safety Course on
D2L before the lab
MasteringPhysics
Assignment 3 due Wednesday October 7th by 11 PM.
Lecture readings from textbook
• Parallel/perpendicular components of acceleration (section 3.2 p.75-77)
• Motion in a circle (section 3.4, p. 85,88)
• Rotational kinematics (sections 9.1-9.3, p. 278-288)
MasteringChemistry
1.2 Introduction due Monday October 5th at 8:30 am
Lecture homework
3-01: (Intro to Thermodynamics)
• Do additional problems at the end of lecture slides
• Read Petrucci 241 – 259
• Carefully examine example 7.2 and 7.3
• Problems Chapter 7: 47 a,b; 49; 55 a,b; 57
• Do “Concept Assessment” page 259
3-02: (Constant Volume/Constant Pressure system)
 Read Petrucci 259 -263
• Problems Chapter 7: 1, 5. 9, 37, 39, 41
• Do two “Concept Assessments” page 231
ASPC 161
QUIZ week 4 in tutorial time slot!! (bring calculator, periodic table and formula
sheet)
 covers everything up to and including Dalton’s Law
Course Project
Selection forms found on Moodle

Concept sketch (orthographic and isometric) due at the start of the lab
period during the week of October 19th
Textbook Readings
Lecture 5 (orthographic projection 4):
4th ed.: 3.6 – 3.17: Isometric sketching
3rd ed.: 6.0 – 6.16: Isometric sketching
Lecture 6 (Isometric Sketching 1)
(4th ed.): 3.18 - 3.24 Curves in isometric view
(3rd ed.): 6.17 - 6.20 Curves in isometric view
ASPC 151
Recommended Homework
 D.8.F: Fillets and rounds: sketch third view
 D.6.B: isometric view from two principal views (Leave construction lines
in)
Lab Manual Readings
Recommended pre-lab reading for Week 4 lab (AKA lab #3) (pages 89-99 in the lab
manual)
Bring to lab:
 Pocket knife
 Magnet
 Textbook (MANDATORY)
APSC 171
Webwork Quiz
Week 3 online quiz due Thursday Oct 8th 11:55 pm.
Practice Problems on D2L
Other
•
•
•
•
MOD 3: Project selection available on D2L, selection form to be filled out
by October 2nd at midnight.
English proficiency test: Monday October 5th [7:00 pm]. Location by
section (check your email!)
GPA fitting October 3rd [8:30 am-5:30 pm] and October 4th [8:30 am12:30pm] at Clark Hall
***If you’re going to be away on the weekend, additional jacket fittings on
October 5th [5:30pm-7:30pm]