REVISION HISTORY
Revision
A
ECO
37-135
Description
Checked
BK
FORMAL RELEASE
NAME
Drawn: Jeffrey Montigny
Checked:
Approved:
Released:
DATE
9/2/14
Approved
RFG
Date
10/6/14
MASSACHUSETTS INSTITUTE OF TECHNOLOGY
Kavli Institute for Astrophysics and Space Research (MKI)
AMPLIFIER, VOLTAGE FEEDBACK
LOW POWER
Size
Code Identification No.
Drawing No.
Rev.
T
80230
37-99010
A
Scale: NONE
Sheet: 1 of 4
1.0
SCOPE
1.1
Introduction
This drawing describes device requirements for Test, Screening, and Qualification of
Analog Devices, Inc. part number AD8038, Low Power, 350MHz Voltage Feedback
Amplifier. The part described herein is packaged in a five lead SC70, plastic, surface
mount package.
1.2
Part Number
The complete MIT part number shall be 37-99010.
2.0
APPLICABLE DRAWINGS
2.1
Specifications
GOVERNMENT
NASA EEE-INST-002
NASA PEM-INST-001
MIL-STD-883
GSFC S-311-M-70
Instructions for EEE Parts Selection, Screening,
Qualification, and Derating
Instructions for Plastic Encapsulated Microcircuits.
Selection, Screening, and Qualification
Test Methods and Procedures for
Microelectronics
Destructive Physical Analysis
KAVLI INSTITUTE FOR ASTROPHYSICS AND SPACE RESEARCH (MKI)
Analog Devices
Data Sheet
AD8038/AD8039
2.2
Archived as MKI Drawing 37-99010.01
Order Of Precedence
In the event of conflict between the text of this drawing and the references cited herein, the
text of this drawing shall govern.
3.0
REQUIREMENTS
3.1
General Requirements
3.1.1
Item Requirements: The parts described herein shall, in all respects, meet all the
requirements of this specification.
3.1.2
Procuring Activity: For the purposes of this specification and documents referenced herein,
the procuring activity is the Massachusetts Institute of Technology Kavli Institute for
Astrophysics and Space Research (MKI).
2
37-99010, Rev. A
3.2.
Part Identification Number (PIN)
Upon successful screening and qualification, Microcircuits shall be identified with the MIT
part number.
3.3
Electrical Performance Characteristics
The absolute maximum ratings and electrical characteristics shall be as specified in MKI
Document 37-99010.01 for the AD8038 device.
3.4
Package And Terminal Connections
The package and terminal connections shall be as specified in MKI Document 37-99010.01
for the SC70 package.
4.0
QUALITY ASSURANCE PROVISIONS
4.1
Screening
All microcircuits for qualification and flight shall be screened per NASA EEE-INST-002,
Section M4, Table 2, for level 2 microcircuits. Serialization is required. For the burn-in
requirement, only the static stress, MIL-STD-883, Method 1015, condition B, is required.
Burn-in shall be performed at Tj = 125°C, for 160 hours minimum. Static burn-in shall be
performed at the operating supply voltage +5V/-5V. Biasing conditions including the value
of RL shall be selected to assure that the junction temperature shall not exceed Tjmax
specified for the device type.
4.2
Qualification
Sample microcircuits shall be subjected to NASA EEE-INST-002, Section M4, Table 3, for
level 2 microcircuits. C-SAM inspection performed during screening shall satisfy the same
requirement in qualification. For the HAST requirement, only the unbiased stress condition
is required.
4.3
Destructive Physical Analysis (DPA)
An internal destructive examination shall be performed in accordance with section 5.0 of
PEM-INST-001. Refer to GSFC S-311-M-70. Sample size shall be five (5) pieces.
3
37-99010, Rev. A
4.4
Measurement Parameters
The following parameters shall be measured:
 DC tests
o Input Offset Voltage
o Input Bias Current
o Common-Mode Rejection Ratio
o PSRR (-Supply and +Supply)
o Quiescent Current per Amplifier
 AC tests
o -3dB Bandwidth
o Slew Rate
4.5
Test Failures
In the event of a failure confirmation, notify MKI Mission Assurance. The failed part shall
be isolated, identified with test failed, and returned to MKI for further action.
4.6
Parts Disposition
All parts shall be returned to MKI, clearly identified, and appropriately packaged. Data
must likewise be delivered to MKI and identified by test and disposition.
5.0
PACKAGING
5.1
Packaging Requirements
Completed parts shall be packaged, packed and protected for prompt and safe shipment to
MKI for immediate use. Tape & Reel packing is preferred.
6.0
NOTES
6.1
Approved Source Of Supply
Microcircuits to be screened and qualified, as described herein, shall be purchased from
Analog Devices, Inc. or its authorized distributor.
6.2
Procurement
Microcircuits shall be sourced from one manufacture lot date code, less than two years old.
The procurement part number is AD8038AKSZ.
4
37-99010, Rev. A