INTRODUCTION
Safety education is a major facet of the instructional program in woodworking. It cannot
be dealt with as something separate; but rather, it must be an integral part of every lesson and
the principles of safety must be applied in every woodworking operation. The entire program
should be based on correct technical information, judgment, and positive behavior. Guards and
safety devices are helpful, but they cannot do the thinking and planning. A good shop safety
program means more than the formulation and enforcement of a set of shop safety rules. It
means that the student must have a safe environment in which to work, that safe practices must
be an integral part of the training, that careful and constant supervision must be provided, that
the teacher must possess a knowledge of the factors that cause accidents, and that the student
must at all times set the example in the following safe practices. Before a student may work in
the shop he/she must study the following precautions, pass the safety test, and have the
instructor’s permission to work in the shop.
PROGRAM OVERVIEW
This program is designed to give the student an opportunity to develop safety habits in
the woodshop. The student will be able to identify what safe working procedures are, and when
the environment around him is unsafe. Everyday contains a variety of safety rules. Follow these
safety rules for a safe working environment for all students.
GENERAL OBJECTIVES
1. The student will have a greater appreciation for safety in the woodshop and will provide
himself and others a safe working environment.
2. The student will become familiar with common machines in the woodshop.
3. The student will become familiar with common power tools in the woodshop.
4. The student will become familiar with common hand tools in the woodshop.
5. The student will know how to conduct himself accordingly to ensure safety for himself and
others.
GENERAL SAFETY RULES
1. An operator or user should familiarize himself with the tools and machinery with which he
will work.
2. Know where all fire extinguishers are located and how to use them.
3. Safety glasses will be worn AT ALL TIMES when in the shop.
4. Under no circumstances should guards be removed from machinery for the sake of
convenience.
1
5. Any unsafe condition of machinery or danger that might cause accidents should be reported
promptly.
6. Repairs, oiling, or adjusting should not be done while the machinery is in motion.
7. Students should not engage in conversations with one operating a machine.
8. Keep your eye and attention on your work, especially when operating a machine.
9. Long sleeves should be rolled above the elbows and loose-hanging tie so arranged as to
prevent entanglement while working on revolving machinery.
10. Avoid wearing loose-fitting clothing, jewelry, or gloves on the hands while working with
machinery.
11. Form the habit of standing clear of all machinery; keep at a safe distance from all moving
parts, and never stand in line with swiftly revolving parts such as jointers, saws, pulleys, and
grinders.
12. When working around a machine, be sure there is good footing and if you notice any slick or
unsafe condition on the floor, inform the instructor.
13. Try to realize the fundamental hazards of industry and to develop an appreciation of a safe
working environment.
14. Endeavor to make safety and caution common habits.
15. When in doubt as to the proper operation of machines or tools, always consult the instructor.
16. Do not leave plane irons, chisels or other edges of pointed tools lying on benches or in
drawers with cutting or pointed edges projecting. Serious injuries may result from such
carelessness.
17. Use care when putting away pieces of lumber so that one will not be injured in passing. This
applies very specifically to pieces on the level with the eye and pointed pieces left so one can
drive them into his body in passing or stooping.
GENERAL SAFETY PRACTICES
1. Remove all rings, watches and any other jewelry.
2. Only one person will be at a machine while it is in operation.
3. Machines will not be operated when the instructor is out of the room.
4. Always turn the power off when you leave the machine.
5. Running, scuffling or horseplay will not be permitted in the shop at any time.
6. Always hand tools to the person who requests them. Do no throw the tool or slide it along
the bench.
7. Avoid making unusual noises that may startle the operator of a machine.
2
8. When the fire alarm sounds, stop work immediately. Turn off the machines and walk to the
assigned exit.
9. If you feel ill, report to the instructor.
10. Report all accidents, no matter how small, to the instructor immediately.
11. If you see oil or grease on the floor, wipe it up; if you see wood on the floor, pick it up; you
may be preventing an accident.
12. Be sure your hands are dry before touching any electrical plug or switch.
13. Keep hand tools off the machines to prevent vibration from drawing them into the machines
or falling on the floor.
14. When climbing to reach high objects, use proper precautions so that you do not slip or fall.
15. When lifting heavy objects, have someone help you.
16. Lift heavy objects by bending at the knees and lifting with your legs, not be bending at the
waist and lifting with your back. If necessary, have someone help you.
17. Take no chances or short cuts when there is a question of possible injury.
18. Never put nails, screws, etc., in you mouth.
SAFE HANDLING OF COMBUSTIBLE MATERIALS
AND SAFE USE OF SPRAYING EQUIPMENT
1. Oily waste and finishing cloths must be disposed of properly. A safety can is provided for
this. USE IT! Never throw oily rags in shavings or into scrap box.
2. All shavings and wood scraps should be swept up and placed into a container that is emptied
daily.
3. Paint, enamel, stain, varnish, lacquer, thinner, shellac, alcohol, kerosene, turpentine, machine
oil, and any other flammable liquids should be stored in a metal cabinet. Each can or
container should be tightly covered.
4. When using finishes in pressurized cans, observe the following precautions: (a) keep cans
away from heat, (b) do not incinerate empty cans, (c) do not puncture cans, (d) avoid
inhalation of vapors and solids; wear a respirator, and (e) follow all manufacturer’s
instructions carefully.
5. Secure special permission from the instructor before spraying operations.
6. Avoid prolonged inhalation of fumes or vapors from finishing materials.
7. Have the spray booth ventilation system in operation during every spraying operation.
8. Wear a respirator if needed.
9. Regulate the air pressure on the spray gun before starting work. Air pressure should be
between 50 and 60 PSI.
3
10. Exercise caution in the handling of compressed air equipment.
11. Read and follow the manufacturer’s directions carefully when using finishing materials.
SAFETY RULES FOR HAND TOOLS
1. Keep all cutting tools sharp. A sharp tool will cut into materials as it should, but a dull tool
requires excessive pressure and may slide over work and out of control.
2. Know the name of each tool and its capacity for doing work.
3. Learn to select and use the proper tool in the proper way. It is safer and the job can be done
faster and better.
4. Examine tools before using them. Report faulty tools immediately.
5. Beware of all hazards. If coping saw blades, drills, or other articles made of tool steel are
bent, twisted, or etc., they may snap and send off flying articles.
6. Beware of tools with mushroomed heads. Hitting such tools with a hammer may cause a
piece of steel to break off and fly across the room.
7. Never pound any hardened metal or tools with a hard faced hammer.
8. Never use a hammer with a loose or split handle or a chipped face.
9. Never use a file without a handle.
10. Keep the fingers away from the handsaw blade when sawing (except when starting a cut).
The saw may jump out of the kerf and skid on the hand.
11. When tools are not in use, place them in a safe position.
12. Never put sharp-edged tools into your pockets.
13. Do not disassemble any tool until the instructor has demonstrated how to do it.
14. Carry shop tools with the cutting edge down and away from your legs.
GENERAL SAFETY RULES FOR THE USE OF
ALL WOODWORKING MACHINES
1. Have each intended operation on the machine checked by the instructor and get his
permission before turning on the power. This is especially important for any special machine
setups.
2.
Use hand tools and processes rather than machines for unimportant operations and for work
on small pieces of stock.
3. Wear aprons that will “tear away” if they get caught in a machine.
4. Stay outside the danger zone while another student is operating a machine.
5. Refrain from talking while operating a machine.
6. Keep your fingers and hands away from the moving parts of the machine.
4
7. Avoid getting into awkward positions when operating machines. Keep your balance, keep
both feet on the floor, and use proper hand positions on the machines and the stock.
8. Never stand in line with a revolving tool.
9. Turn on the light if there is one on the machine.
10. Keep all safety guards in proper positions while machine is in operation.
11. Fasten all adjustments securely before power is turned on.
12. Remove all wrenches, tools, and extra material from the machine before the power is turned
on.
13. Shut off the power and notify the instructor at once of the machine is not working properly or
unusual noises develop.
14. Never use a cutting blade that is dull.
15. Inspect wood carefully for nails, screws, paint, or loose knots before machining.
16. Never feed a machine until it has reached full momentum.
17. Never force stock into a machine faster than it will normally cut.
18. Never hurry when working at a machine.
19. Never attempt to stop a machine after the power is turned off by catching moving parts or by
applying friction with the hand.
20. Allow the machine to come to a dead stop before oiling, cleaning, or adjusting it.
21. Clean scraps from machine with a brush.
22. Never leave a machine until it has come to a dead stop.
23. Place the machine in normal position and condition when finished. Remove any special
setups and put waste in the scrap box.
24. You are not forced to use any machine or tool. You may be excused from using them be
seeing your instructor.
25. If you are in doubt about the use of a tool or machine, be sure to ask your instructor for help.
RADIAL ARM SAW SAFETY RULES
1. Always cut on the forward stroke of the machine.
2. Set and use the anti-kickback device for all ripping operations. The fingers of this device
should extend slightly below the top surface of the stock to be cut.
3. Set the stay guard to clear the work by about one-eighth of an inch on the infeed side.
4. Always feed stock to the “infeed” end of the saw when ripping or in an operation where the
stock is moved into the blade.
5
5. Hold stock securely against the fence.
6. Use a push stick for feeding stock in close proximity to the saw blade.
7. Use care not to make unnecessary cuts in the tabletop. The saw need only scratch the wood
table to cut off the stock completely.
8. Keep the saw table clear of scraps, but never remove scrap until the saw has been returned
to position behind the fence.
9. Safety margin is 6 inches.
10. Extend your arm stiffly when pulling the saw through a cut.
11. Only crosscutting operations should be made on this saw.
TABLE SAW SAFETY RULES
1. Safety margin is 4 inches. Use a push stick when ripping stock that is less than four inches
wide.
2. The most important guard on the saw is the splitter.
3. Minimum length of stock is 12 inches.
4. Obtain permission from the instructor for each intended circular saw operation and
have each machine setup checked by the instructor before the power is turned on.
5. Always keep the guard down over the saw while the machine is in operation except
when crosscutting or special setups. Get instructor’s help if in doubt of proper use of
guards.
6. Use a saw blade that is designed for the work.
7. Never allow the saw blade to project more than 1/4 of an inch above the stock to be cut.
8. Do not stand directly behind or in line with the saw blade.
9. Do not use the ripping fence for a stop when crosscutting unless a clearance block is
attached to the fence.
10. Never rip stock wider than long.
11. Never allow the hands to cross the line of the saw while the machine is in operation.
12. Be sure that you know specifically what you’re going to do before you turn on the power.
13. Be sure that the saw will clear the table, the fence, the crosscutting guide, and other special
setups before turning on the power, especially if in a tilt position.
14. Do not reach over the saw.
15. See that no fence or setup is in the line of the saw before turning on the power.
6
16. Lower the saw blade below the table level and put the guard down before leaving the
machine.
17. Remember when helping to “tail off” in the saw that the only purpose is to support the stock
while the operator pushes it through the saw.
18. Use care in sawing through knots. Never saw through loose knots.
19. Do not saw warped or rough stock on the saw.
20. When ripping stock the working face must be flat on the table and the working edge against
the fence.
21. When crosscutting stock the working face must be flat on the table and the working edge
against the miter gauge.
22. Never saw “FREEHAND.”
23. Hold stock firmly when cutting, when ripping apply pressure against the fence, when
crosscutting apply pressure against the mitre gauge.
24. Never attempt resawing without first getting special permission.
25. Never attempt to lower stock over the saw. This operation requires special setup and
instructor’s supervision.
26. Do not allow the left hand to pass the front edge of the saw.
27. Arch the fingers while feeding instead of laying the hands flat.
28. Never attempt to clear scrap away from the blade while it is running. Stop the machine if this
is necessary, and use the push stick to remove scrap.
29. Never attempt to cut round stock on the table saw without a holding jig.
30. Stand to the left of the blade for the most operations.
BAND SAW SAFETY RULES
1. Safety margin is 2 inches
2. Set the saw guard and guide within 1/4 of an inch of the stock being cut.
3. Be sure that the radius of cutting on curves is not too small for the blade. Make radial relief
cuts.
4. Place the stock on the saw table so that it lies flat and firm.
5. Plan the sawing procedure so that there will be maximum forward feed and a minimum of
backing out. Number the order of cuts and make necessary relief cuts.
6. Do not back out of stock unless the blade is at a dead stop.
7. Do not use fingers to remove scrap.
8. Do not place the hand across the line of the saw.
7
9. Do not stand at the right side of the saw when the blade is in motion. If the blade should
break, it has a tendency to be thrown to the right.
10. Never cut round stock on the band saw. Cutting of round stock requires the use of special
holding jigs.
11. Do three things if the blade breaks: (1) keep clear, (2) turn off the power, and (3) notify the
instructor.
12. Never turn the band saw on with the band wheel covers off.
JOINTER SAFETY RULES
1. Safety margin is 4 inches.
2. Hold the stock firmly on the table or against the fence.
3. Change the position of the hand so that they do not pass directly over the cutters when
feeding, and never drag the thumb or fingers behind the stock.
4. Never lean the stock against the jointer of pile stock on the bed.
5. Use a push block when jointing narrow or flat pieces of stock.
6. Never joint stock less than 1/2 inch thick, 1 inch wide, or less than 10 inches long.
7. Never cut deeper than 1/8 inch without first getting special permission from the instructor.
8. Adjust the depth of cut before the power is turned on.
9. End grain should not be run over the jointer without special permission.
10. NEVER change the adjustment of the out-feed table .
11. Keep the guard closed over the knives at all times while the jointer is being operated. Do not
pull the guard open with the fingers.
12. Turn the power off and allow the machine to come to a dead stop before leaving.
13. Do not attempt to run odd-shaped pieces over the jointer.
14. Do not stand directly behind the jointer when using the machine.
15. Cover the cutterhead with a back guard if the fence is moved across the bed.
16. Knives should not be exposed more than necessary to do the job.
17. Maximum depth of cut when facing is 1/16 of an inch.
18. Maximum depth of cut when edge jointing is 1/8 of an inch.
8
SURFACER SAFETY RULES
1. Make certain that the stock has no large cracks, loose knots, nails, screws, dirt, paint, or
varnish on any of the surfaces.
2. Do not stand in direct line with the position of the rotation of the planer head or directly
behind the board that is being fed.
3. Never allow the planer to run unattended.
4. Do not plane the edge of a board in the planer.
5. Never plane two boards side by side. One board may be thinner than the other, and it may
result in kickback.
6. Do not change the depth of the cut while the board is being fed through.
7. Never attempt to shift a board after it has been gripped by the feed rolls.
8. Do not allow the hands to come near the feed rollers, and keep “hands off” boards that are
gripped by the feed rollers.
9. Do not plane stock that is less than 1/4 inch thick unless it is placed on a carrier board for
support.
10. Limit the depth of the cut to 1/8 of an inch for narrow stock and on 1/16 of an inch for stock of
full planer width.
11. Minimum length of stock is the distance between rollers plus 2 inches. For this machine, it is
14 inches.
12. Do not look into the machine while it is running.
GRINDER SAFETY RULES
1. Wear goggles or face shields that shield the eyes from all directions while grinding.
2. Keep the tool rest as close to the wheel as possible. Under no conditions should the
distance between the tool rest and the wheel exceed 1/8 of an inch.
3. Apply work gradually to a cold wheel.
4. Avoid grinding on the side of a light wheel. Side grinding only on wheels designed for that
purpose.
5. Keep the fingers clear of the wheel. Get prompt first aid if you are injured by the grinding
wheel.
6. Keep the path of the wheel travel clear of any obstructions.
7. Do not rub the face or eyes with hands that are soiled with emery dust.
8. Do not stand in line with the wheel when starting the grinder. Faulty grinding wheels usually
break on the start.
9
9. Hold small pieces securely in a proper holder.
DRILL PRESS SAFETY RULES
1. Safety margin is 2 inches.
2. Check to make certain that the bit is securely fastened in the drill chuck before starting the
machine.
3. Adjust the belt into the proper pulley combinations for the required speed. Belt guard must
be in place before operation of the machine.
4. Hold stock securely on the table.
A. Clamp it on the table if it cannot be held by hand.
B. Place small pieces in a vise or jig to hold them in position for drilling.
C. Place circular shaped material in a “V” block for drilling.
5. Place the hole in the center of the table directly under the drill to prevent its striking the table
or drill on a table block.
6. Set the depth stop to the required depth if the hole is not being drilled through the stock.
7. Withdraw the bit frequently when drilling deep holes to prevent “burning” and “freezing” of
the bit in the stock.
8. Check to make certain that the chuck key and wrenches are all removed before starting the
machine.
9. Follow the safety suggestions for the particular machine you are adapting the drill press to
replace when using the drill press for routing, shaping, mortising, sanding, planing, or other
special jobs.
10. Operate the feed handles so that the drill cuts evenly into the work.
11. Ease up on the feed pressure when the drill begins to break through the materials.
12. Never attempt to use wood bit for drilling in metal.
13. Do not allow the drill press to exceed 3,000 R.P.M. when boring holes up to3/4 inch diameter.
14. Reduce the speed when boring deep holes to keep the bit from heating.
15. Reduce the speed when boring holes in hardwood to keep the bit from heating.
16. Bore larger diameter holes at the slowest drill press speed.
SHAPER SAFETY RULES
1. Be sure the knives are fastened securely on the arbor.
2. Make a thorough check of the setup before turning on the power.
3. Be sure both sides of the fence are in line when cutting straight stock.
4. Use stop blocks when making a cut within the limits of the piece of stock.
10
5. Select a collar size, which will conform as nearly as possible to the smallest curve in the form
to be shaped (irregular shaping).
6. Use the pin in the table when “riding a collar.”
7. Select a cutter that is designed to cut on the underside of the stock if possible.
8. Always use the guard and hold-down devices.
9. Hold the stock firmly against the fence or collar.
10. When using the rub collar for a guide, start the cut away from the corners. This is especially
true when shaping around the entire end of the board.
11. Boards less than eight inches wide should not be shaped on the end unless the shaper has a
sliding guide or jig to clamp the board and hold it in place.
12. Safety margin is 4 inches.
13. Cut with the grain whenever possible; advance the stock very slowly when cutting against
the grain, and never cut against the grain unless it is impossible to work with the grain.
14. Never back up; stock must always be advanced against the rotation of the cutters.
15. Be sure that the knives are kept sharp.
16. Be sure that you know the correct direction of the shaper rotation; this would probably ruin
the motor.
WOOD-TURNING LATHE SAFETY RULES
1. Face shield and safety glasses for eye protection from dust and chips should be worn.
2. USE SHARP TOOLS. Dull tools are dangerous.
3. Allow adequate drying time for glued turning stock
4. Remove the live center from the head stock and drive it into the center of one end of the
stock with a mallet. Imbed the spurs firmly into the wood. Saw diagonal saw kerfs in the end
of the stock for the live center spurs to enter if necessary.
5. Place the live center and stock in the lathe and force the dead center into the center of the
other end until the sharp edge of the dead center cup cuts a groove into the wood. Retract
the dead center and place a small amount of lubricant (oil, grease, or soap) in the dead center
cup. Reinsert the dead center and make sure it has a snug, but not tight, fit. (If tight, the end
will heat and burn when operating the lathe.)
6. Lock all adjustments on the tailstock, fastening the stock securely between center.
7. Set the tool rest so that its top edge is about 1/16 inch above the center of the stock being
turned, and 1/8 of an inch from the work.
8. Before turning on the power, rotate the stock by hand making certain that it does not touch
any part of the lathe.
11
9. Fasten face plate work securely to the face plate (screws must be checked frequently to
prevent loosening).
10. Fasten the face plates securely to the lathe before the power is turned on.
11. Use slow speeds for face plate work of large diameter.
12. Saw stock that is to be used for face plate work into a circular shape before fastening it to the
face plate.
13. Place face plate screws so that the lathe tool will not strike them when turning.
14. Regulate the lathe speed as follows: (a) stock is turned at slow speed until it is
cylindrical in shape; (b) stock over six inches in diameter should be turned at speeds
below 1,000 R.P.M.; (c) stock below three inches in diameter should be turned safely at
speeds ranging from 3,600 R.P.M. down; (d) in most cases, the slower speeds are the
safest; (e) when turning “off-center” work the slower speeds must be used; (f) split
turning and segmented work must be checked by the instructor before being placed in
the lathe.
15. Remove the tool rest when sanding or finishing on the lathe.
16. Use a cloth pad with no loose threads as an applicator for finishes.
17. Be sure that the lathe tools are securely held by their handles and will not slip out of the
handles.
18. Do not overload or stop the motor by sanding or drawing the dead center up too tightly.
19. Never stand directly in front of the stock when turning on the machine.
20. Never attempt a shearing cut until special instruction and permission of the instructor has
been given.
21. Do all face plate work with scraping tools only. Never use a gouge inside of a cup-shaped
piece.
22. Be very careful never to touch the chisel against the “up travel” side of the face plate work.
23. Hold turning tool firmly with both hands while cutting stock in the lathe.
24. Stop the lathe before taking caliper measurements.
25. Use only woodturning chisels for lathe work.
26. Never touch revolving stock with the fingers.
DRUM SANDER (FLOOR MODEL MACHINE)
1. Do not attempt to sand stock that is less than 9 inches long.
2. Carefully measure the thickness of the stock and set the machine to the thickness.
3. Move the hand wheel a maximum of only 1/8 of a turn per pass.
12
4. Do not continually run the stock through the machine in the same place.
5. Do not attempt to run stock of varying thicknesses through the machine at the same time
side by side.
6. Short pieces should be run end to end.
7. If the amp meter moves past 25, you are making too heavy of a pass. Run it through several
times without changing the settings.
8. If the machine quits or is sanding unusually get the instructor. Do not attempt repairs.
MORTISER SAFETY RULES
1. Safety margin is 4 inches.
2. Check the bit and chisel. They must be sharp and securely fastened in the machine before it
is started.
3.
The auger bit should extend about 1/8 inch beyond the end of the chisel for
clearance.
3. All set screws should be completely recessed.
4. Set the tale low enough so the chisel will not strike it at the bottom of the cutting stroke.
5. Turn the bit around one complete revolution by hand before the power is turned on.
6. Fasten all stock securely in position.
7. Do not brush chips away with the hands.
BELT/DISC SANDER
1. Safety margin, 2 inches.
2. Turn on dust collection system.
3. Hold work firmly when making a pass.
4. Sand against the direction of the spindle.
5. Sand on the down side of the disk.
6. The best use for the disk sander is for sanding end grain.
7. Watch belt tracking on the belt sander.
8. To keep from burning the work piece move it continually.
9. Never hold small pieces by hand.
10. Stop the sander before making any adjustments.
13
11. Check the abrasive disc for breaks and tears and make certain that it is securely fastened.
12. Never try to sand metal on the sander—it is used for wood only.
PORTABLE POWER TOOLS
PORTABLE SANDERS
1. Check to make sure the switch is “off” before you plug it in.
2. Empty the dust collector/bag after every use and blow the power tool clean with the air hose.
3. Never place a power sander on the bench while it is running. Place sander on it’s side.
4. Work with the cord over an arm so that the machine does not run over it.
PORTABLE ELECTRIC DRILL
1. Remove the chuck wrench before starting the drill.
2. Disconnect the drill cord from the outlet at times when the drill is not in use.
ROUTER
1. Unplug router before changing cutter or making adjustments.
2. Check condition of router before preparing to use.
3. Turn off router when not in use. Place router in the center of the table when not in use.
4. Hold router firmly when turning on power to overcome starting torque of the motor.
5. Never turn on power until you are in working position and the router cord is free to follow.
6. Do not use dull, rusty, or gummed bits.
7. Always lay router down with it pointing away from you.
8. Secure work firmly to work surface.
9. Keep router moving to prevent burning.
10. Make sure bit is properly installed before turning on the router.
11. When using the router in a cutting table, keep fingers at least 4” from cutter.
12. Remove adjusting keys and wrenches before turning on router.
13. Be sure 2/3 of the bit shank or at least 1/2 inch of the bit shank is in the chuck before
tightening collet nut. If the bit slips, even though it is tight, the collet is typically either dirty
and needs to be cleaned or is worn out and needs to be replaced.
POWER MITERBOX
1. Make certain blade is not engaged in stock before starting the machine.
14
2. Stock must be securely held on table and against fence.
3. Safety margin is 4 inches.
4. Do not cut stock that is wider than the table width.
PORTABLE CIRCULAR SAW
1. Check the blade carefully for cracks or damage before operation.
2. Be careful not to damage the arbor, flanges or bolt.
3. Make sure that the base and workpiece are properly secured so they will not move during
operation.
4. Inspect for and remove all nails from the workpiece before operation.
5. Make sure the blade is not contacting the workpiece before the switch is turned on.
6. Wait until the blade attains full speed before cutting.
7. Do not attempt to lock the trigger in the “on” position.
8. Always switch off and wait for the blade to come to a complete stop before removing,
securing workpiece, and changing workpiece position, angle or the blade itself.
9. Do not abuse the cord. Never yank cord to disconnect it from the receptacle.
10. Adjust the saw blade to a depth 1/8-inch greater than the thickness of the material being cut.
AIR NAIL GUNS
1. CONNECT TOOL TO AN AIR SUPPLY HOSE WITH A
COUPLING THAT REMOVES ALL PRESSURE FROM THE TOOL
WHEN THE COUPLING IS DISCONNECTED.
2. DISCONNECT TOOL FROM THE AIR SUPPLY HOSE BEFORE DOING TOOL MAINTENANCE,
CLEARING A JAMBED FASTENER, LEAVING THE WORK AREA, MOVING TOOL TO
ANOTHER LOCATION, HANDING THE TOOL TO ANOTHER PERSON, OR MAKING
ADJUSTMENTS.
3. DO NOT ALTER OR REMOVE SAFETY, TRIGGER, OR SPRINGS.
4. KEEP THE TOOL POINTED AWAY FROM YOURSELF AND OTHERS AT ALL TIMES.
5. DO NOT LOAD FASTENERS WITH TRIGGER OR SAFETY DEPRESSED TO PREVENT
UNINTENTIONAL FIRING.
6. NEVER CARRY TOOL WITH YOUR FINGER ON THE TRIGGER.
7. DON’T OVERREACH. KEEP PROPER FOOTING AND BALANCE.
15
16