TENDERDOCUMENTS ARTOS® Sigma 1
CONTENTS
TENDERDOCUMENT double flat + clevis ARTOS® Sigma 1
2
TENDERDOCUMENT rod + eyebolts ARTOS® Sigma 1
4
TENDERDOCUMENT stretching frame big ARTOS® Sigma 1
6
TENDERDOCUMENT stretching frame small ARTOS® Sigma 1
8
1
TENDERDOCUMENT double flat + clevis ARTOS® Sigma 1
Tender documents for stainless steel wire mesh
Pos. 1
Stainless steel wire mesh
ARTOS® ANDRITZ Kufferath - Wire Mesh for architecture
piece
type:
ARTOS® Sigma 1
warp cable:
4 x Ø 2.0 mm
weft wire:
Ø 2.75 mm
pitch:
50 x 6 mm
weight:
9.76 kg/m²
open area:
ca. 39.80 %
material:
stainless steel AISI 304 / stainless steel AISI 316L
delivery of wire mesh panels:
total amount sqm.
length warp cable (max.) 20,000 mm x width weft wire (max.) 8,500 mm
cut to size, cable welded end
included mounted stainless steel double flat 50 x 4 mm at top and bottom
grounded surface
included _ pcs. stainless steel clevis M 12 x 120 mm for tension of the mesh
(starting at a total length more than 3,000 mm, generally for each floor)
including for each panel xx inserted stainless steel rod Ø 20mm for medium fixing
Pos. 2
Top fixing point
piece
delivery of stainless steel brackets according structural engineering
for top fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
Pos. 3
Medium fixing point
(starting at a total length more than 3,000 mm, generally for each floor)
piece
delivery of stainless steel rod with leaks and brackets according structural engineering
for medium fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
Pos. 4
Bottom fixing point
piece
delivery of stainless steel brackets according structural engineering
for bottom fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
2
Pos. 5
Installation
1 piece
professional installation of all panels and accessories mentioned before including
tensioning according to manufacturers´ instruction at a steel/concrete substructure by
others, all costs for any chain hoist has to be budget
installation area has to be trafficable for heavy equipment
installation height: ……. m above terrain level
Pos. 6
Design and structural engineering
1 piece
delivery of shop drawings for release considering the scheduled steel/concrete
substructure by others
delivery of a structural engineering for dimensioning of all fixing points including
necessary tensioning
calculation of wind load, snow load and dead load
the dimensioning of the steel/concrete substructure by others
3
TENDERDOCUMENT rod + eyebolt ARTOS® Sigma 1
Tender documents for stainless steel wire mesh
Pos. 1
Stainless steel wire mesh
ARTOS® ANDRITZ Kufferath - Wire Mesh for architecture
piece
type:
ARTOS® Sigma 1
warp cable:
4 x Ø 2.0 mm
weft wire:
Ø 2.75 mm
pitch:
50 x 6 mm
weight:
9.76 kg/m²
open area:
ca. 39.80 %
material:
stainless steel AISI 304 / stainless steel AISI 316L
delivery of wire mesh panels:
total amount sqm.
length warp cable (max.) 20,000 mm x width weft wire (max.) 8,500 mm
cut to size, cable welded end
including:
stainless steel rod Ø 26mm inserted at the top and bottom point
eyebolts M12 x 100 mm all 500 mm at top+bottom rod for tension of the mesh
(starting at a total length more than 3,000 mm, generally for each floor)
including for each panel xx inserted stainless steel rod Ø 20mm for intermedium fixing
Pos. 2
Top fixing point
piece
delivery of stainless steel brackets according structural engineering
for top fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
Pos. 3
Intermedium fixing point
(starting at a total length more than 3,000 mm, generally for each floor)
piece
delivery of stainless steel leaks and brackets according structural engineering
for intermedium fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
Pos. 4
Bottom fixing point
piece
delivery of stainless steel brackets according structural engineering
for bottom fixing including all necessary fixing accessories, max. cantilever 30 cm
material stainless steel AISI 304 / stainless steel AISI 316L
4
Pos. 5
Installation
1 piece
professional installation of all panels and accessories mentioned before including
tensioning according to manufacturers´ instruction at a steel/concrete substructure by
others, all costs for any chain hoist has to be budget
installation area has to be trafficable for heavy equipment
installation height: ……. m above terrain level
Pos. 6
Design and structural engineering
1 piece
delivery of shop drawings for release considering the scheduled steel/concrete
substructure by others
delivery of a structural engineering for dimensioning of all fixing points including
necessary tensioning
calculation of wind load, snow load and dead load
the dimensioning of the steel/concrete substructure by others
5
TENDERDOCUMENT stretching frame big ARTOS® Sigma 1
Tender document for stainless steel wire mesh
Pos. 1
Stretching frame construction length x width max. 15,000 mm x max. 3,500 mm
(free choice of sizes)
1 piece
ARTOS® ANDRITZ Kufferath stretching frame construction consist four sided of
square hollow profiles and x medium bars consists of square hollow profiles,
length (max.) 15,000 mm, width (max.) 3,500 mm. The frame construction has to be
realized to that the following mesh installation description, a linear extension of
min. 50 mm can be absorbed by the total frame construction due to a mechanical
tensioning up to the total length mentioned above. Due to the tensioning device the
seated mesh panel has to be tensioned up to fully flatness. The pretension has to be
selected that all wind loads, material extension due to variations in temperature and
dynamical deformation caused by mounting, the fully flatness of the mesh is not
affected.
Profiles: closed frame 100/100/6 mm, max. 15,000 mm x max. 3,500 mm steel S235,
Medium bars square hollow profile 100 x 60 mm length ca. 3,300 mm.
Attention of the frame sizes on delivery and mounting, if necessary delivery of the
frames in single components and construction on site screwing, including all necessary
bolted connection, push pads, drill holes, long holes etc.
Including fixing clamps, flats for fixing on steel construcition by others,
Including all necessary fixing accessories
Profiles made by norm EN 10219 part 1+2.
All frame parts hot-dip galvanized according to DIN
Pos. 2
Stainless steel wire mesh
ARTOS® ANDRITZ Kufferath - Wire Mesh for architecture
piece
type:
ARTOS® Sigma 1
warp cable:
4 x Ø 2.0 mm
weft wire:
Ø 2.75 mm
pitch:
50 x 6 mm
weight:
9.76 kg/m²
open area:
ca. 39.80 %
material:
stainless steel AISI 304 / stainless steel AISI 316L
wire mesh panels accordingly to stretching frame sizes,
length warp cable (max.) 15,000 mm x width weft wire (max.) 3,500 mm
including mounting and professional tensioning of wire mesh panels on
above named stretching frames.
panels deflashing sideways, cable ends just fixed (all ~100 mm cable ends welded)
panel fixing at the medium bars with stainless steel cable connectors according
structural engineering. The cable connectors have to be secured against slipping.
6
Pos. 3
Surcharge Steel
1 kg
surcharge for quantity increase or reduction for section of steel frame construction
according structural engineering
Pos. 4
Cover profile
piece
stainless steel end plate L 100x100x3mm,
length 3,500 mm, 1.4301/AISI 304 - 1.4404/AISI316L for vertical covering of panel
ends, delivery and mounting including all necessary fixing accessories
Pos. 5
Installation
1 piece
professional installation of all stretching frames mentioned before including
tensioning according to manufacturers´ instruction at a steel/concrete substructure by
others, all costs for any chain hoist has to be budget
installation area has to be trafficable for heavy equipment
installation height: ……. m above terrain level
Pos. 6
Design and structural engineering
1 piece
delivery of shop drawings for release considering the scheduled steel/concrete
substructure by others
delivery of a structural engineering for dimensioning of the stretching frame,
calculation of wind load, snow load and dead load
the dimensioning of the steel/concrete substructure by others
7
TENDERDOCUMENT stretching frame small ARTOS® Sigma 1
Tender document for stainless steel wire mesh
Pos. 1
Stretching frame construction length x width max. 2,000 mm x max. 2,000 mm
(free choice of sizes)
piece
ARTOS® ANDRITZ Kufferath stretching frame construction consist four sided of
square hollow profiles, length (max.) 2,000 mm, width (max.) 2,000 mm
The frame construction has to be realized to that the following mesh installation
description, a linear extension of min. 30 mm can be absorbed by the total frame
construction due to a mechanical tensioning up to the total length mentioned above.
Due to the tensioning device the seated mesh panel has to be tensioned up to fully
flatness. The pretension has to be selected that all wind loads, material extension due
to variations in temperature and dynamical deformation caused by mounting, the fully
flatness of the mesh is not affected.
Profiles: closed frame 50/50/4 mm, max. 2,000 mm x max. 2,000 mm steel S235,
Attention of the frame sizes on delivery and mounting, if necessary delivery of the
frames in single components and construction on site screwing, including all necessary
bolted connection, push pads, drill holes, long holes etc.
Including fixing clamps, flats for fixing on steel construcition by others,
Including all necessary fixing accessories
Profiles made by norm EN 10219 part 1+2.
All frame parts hot-dip galvanized according to DIN
Pos. 2
Stainless steel wire mesh
ARTOS® ANDRITZ Kufferath - Wire Mesh for architecture
piece
type:
ARTOS® Sigma 1
warp cable:
4 x Ø 2.0 mm
weft wire:
Ø 2.75 mm
pitch:
50 x 6 mm
weight:
9.76 kg/m²
open area:
ca. 39.80 %
material:
stainless steel AISI 304 / stainless steel AISI 316L
wire mesh panels accordingly to stretching frame sizes,
length warp cable (max.) 2,000 mm x width weft wire (max.) 2,000 mm
including mounting and professional tensioning of wire mesh panels on
above named stretching frames.
panels deflashing sideways, cable ends just fixed (all ~100 mm cable ends welded)
8
Pos. 3
Cover profile
piece
stainless steel end plate L 50x50x3mm,
length 2,000 mm, 1.4301/AISI 304 - 1.4404/AISI316L for vertical covering of panel
ends, delivery and mounting including all necessary fixing accessories
Pos. 4
Installation
1 piece
professional installation of all stretching frames mentioned before including
tensioning according to manufacturers´ instruction at a steel/concrete substructure by
others, all costs for any chain hoist has to be budget
installation area has to be trafficable for heavy equipment
installation height: ……. m above terrain level
9