Errata for Thermodynamics

advertisement
Rev. 6/19/14
ERRATA – Thermodynamics: Concepts & Applications
p. 55 -
Add red background to Eq. 2.20
p. 64 -
Fig. 2.8: 500 kPa should be 400 kPa
p. 69 -
5 lines from bottom (not counting footnote): “Eqn. 3.32” should be “Eqn.
2.32”
p. 83 -
4 lines above Self Test: delete “fairly”
p. 86 -
Italic T & h in table
p. 86 -
h(320 K) should be h(820 K) 2 locations
p. 91 -
4 lines from bottom of text; 1st sub-bullet: “and” should be “or”
p. 110 -
Horizontal scale label should be v not s
p. 112 -
Fig. 2.29: Remove red overlying curve over top of steam dome
p. 116 -
Footnote: “superseded” not “superceded”
p. 119 -
Fig. 2.33 RH axis units: Add “sub m” to “lb”, i.e., “lbm”
p. 122 -
Possibly add add’l approximation: u = cvT
p. 124 -
Fig. 2.34: Tweak triple point pointer to point at bold dot
p. 130 -
Footnote 17: Change “temperature” to “pressure”
p. 147 -
Prob. 2.34: Add period after “P2”
p. 153 -
Prob. 2.105: Insert “1 kg of” after “contains”
p. 153 -
Problem 2.112: Change “0.136” to “1.36” kg
p. 158 -
Denominator of Eqn. 2A.3: “ ‘ ” should be “ ! ”
p. 178 -
First unnumbered equation: Change bold “V” to unbold “V”
p. 208 -
Prob. 3.22: Change “170°C” to “169°C”
p. 231 -
Vertical scale label should be “P” not “T”
Rev. 6/19/14
p. 254 -
Caption to Fig. 4.16; Courtesy line should read “Photographs (b, c, d) by
Paul Ruby, (a) by Sibtosh Pal …”
p. 262 -
Need to redraw figure to show lead wires & perspective more accurately.
p. 287 -
2nd line above Self Test: “polystyrene”
p. 299 -
First line: Capital W in “With”
p. 299 -
2nd equation: Q-dot not Q
p. 299 -
10th line: “yields” not “yield”
p. 316 -
Ex. 5.14: Change T2 to T4 in drawing following problem statement.
p. 320 -
Self Test 5.11: Answer should be “9.5 m/s”
p. 321 -
Eqn. 5.28: Delete subscript “in” on “m-dot”
p. 338 -
Enthalpies in problem 5.80 should be 2856.5 kJ/kg and 2562.2 kJ/kg,
respectively. Note change in Answers to Selected Problems (p. 719) for
this problem.
p. 347 -
3rd line: “generated” should be “generalized”
p. 349 -
Self Test 6.1: Delete “and pressure”
p. 361 -
Side bar: “Chapter 1” should be “Chapter 2”
p. 363 -
Note that regeneration must be used to meet only 2 reservoir, constant-T
requirement in Stirling cycle.
p. 364 -
Fig. 6.14: “W-dot-1-2” should be “W-dot-4-1”
p. 370 -
Sentence above Eqn. 6.22a should begin “For Case II” (not Case I),
whereas sentence below Eqn. 6.22a should begin “For Case I” (not Case
II).
p. 371 -
Eqns. 6.24a,b need red backgrounds.
p. 377 -
Self Test 6.6: Add masses to parenthetical material: “(2 kg copper and 2.5
kg iron)”
p. 378 -
4th line in Analysis: “6.3588” should be “7.3588”
p. 379 -
Last entry 3rd line of table “6.2207” should be “7.2207”
Rev. 6/19/14
p. 392 -
Answer to Self Test 6.9: Insert solidus before (1/Pº), i.e., “/(1/Pº)”
p. 399 -
Eqn. 6.59: “ – “ should be “+”
p. 400 -
Eqn. 6.61a: Add subscript “1” to “S” and “V”
p. 400 -
Eqn. 6.61b: Add subscript “1” to “S”
p. 400 -
Eqn. 6.61c: Add subscript “1” to “s”
p. 401 -
8th line form bottom:”120/0.14808” should be “101.25/0.1672”
p. 408 -
Last term in first equation should have negative sign, i.e.,
“–T0(s1 – s0)”; same error in following equation in which numbers are
substituted.
p. 408 -
8th line: Change “15,270” to “4780”
p. 408 -
9th line: Change “W” to “kW”
p. 415 -
Sketch in 6.2: Turbine: “W-dot-in” should read “W-dot-out”
p. 416 -
Problem 6.8: Replace “An ideal gas” with “Air”
p. 418 -
Problem 6.27 Part B looks bogus – need to check.
p. 421 -
Problem 6.70: Remove circle from integral sign.
p. 580 -
Problem 6.111: “mole function” should read “mole fraction”
p. 427 -
Problem 6.137: Change “fill” to “full”
p. 455 -
5th line under subheading Isentropic Flows: Inequalities are reversed.
Should read: “P0 > Pb ≥ Pc”
p. 472 -
Eqn. 7.34d: Add “g” in denominator of last term
p. 489 -
Change values for h1 and h2 (2 locations) to “1798.6” and “861.1”,
respectively, to agree with Table C.2 values
p. 495 -
Eqn. 7.51: Add subscript “C” to m-dot on RHS
p. 495 -
Eqn. 7.53a: Add subscript “H” to m-dot on RHS
p. 495 -
Eqn. 7.53b: Add subscript “C” to m-dot on RHS
Rev. 6/19/14
p. 506 -
Ch 7 Problem Subject Areas: Change “7.21” to “7.20” & change “7.22” to
“7.21”.
p. 510 -
Prob. 7.32: Change “at the nozzle exit Pe” to “in tank B”
p. 513 -
Problem 7.70: insert “per unit mass of working fluid” after “work done”.
p. 522 -
5th line from bottom of text: “reversibility” should be “reversibly”.
p. 583 -
6th line: Replace spurious Greek symbols with left & right square brackets
p. 593 -
Example 12.15: Change “mm Hg” to “in Hg” in problem statement and in
Analysis section.
p. 595 -
2nd line: Replace “ ≥ ” with “ / ”
p. 603 -
4th equation from bottom: Replace “hl,3” with “hf,3”
p. 615 -
Part B: Portion should read: “(economizer, steam generator, superheater,
and reheater combined)”
p. 617 -
Problem 8.38: Change “Example 8.10” to “Example 8.8”
p. 617 -
Problem 8.39: Change “Example 8.9” to “Example 8.7”
p. 617 -
Problem 8.41: Change “Example 8.11” to “Example 8.9”
p. 617 -
Problem 8.43: Formula for iso-octane should be “C10H18”
p. 619 -
Problem 8.55: Replace “compression” with “heat addition”
p. 620 -
Problem 8.59: Add “per unit mass” to the end of the last sentence.
p. 620 -
Problem 8.60: Add “per unit mass” to the end of the last sentence.
p. 620 -
Problem 8.63: Change pressure ratio from “8.5” to “12.5”
p. 621 -
Problem 8.70: Change pressure ratio from “8.5” to “12.5”
p. 621 -
Problem 8.70: Add to Part C “The turbine inlet temperature is 1500 K.”
Modify Part D, 2nd & 3rd lines to read “thermal efficiency for no
regeneration. Discuss.”
p. 621 -
Problem 8.70: Add to Part C “The turbine inlet temperature is 1500 K.”
Rev. 6/19/14
Modify Part D, 2nd & 3rd lines to read “thermal efficiency for no
regeneration. Discuss.”
p. 628 -
Prob. 8.126: Reword: “…0.15 MPa. Does any moisture condense? If so,
determine the moisture condensation rate (kg/min). If not, determine the
relative humidity.”
p. 628 -
Problem 8.135: Insert “(dry basis)” after “4-lbm mass of air” and after “1lbm mass of air”.
p. 629 -
Problem 8.139: Add “at 1 atm” to the end of the last sentence.
p. 629 -
Problem 8.143: Add word “flow” after word “mass” in Parts B & C.
p. 632 -
Problem 8.170: Change “is maintained” to “contains air”.
p. 539 -
Add arrowhead to “Steam out”
p. 683 -
Property headings on columns 3-7 should have subscripts “g”
p. 694 -
Table heading should be “Table G.2A” not “G2.A”. Similarly for tables
B – E.
p. 677 -
Table D.3V heading: Replace “24.0” with “26.0”
p. 717 -
Round answers to Problem 2.17c and 2.17d to five significant digits:
51,386 kJ/kmol, 56,364 kJ/kmol
p. 718 -
Prob. 2.96: Answer should be 0.00230 kg
p. 718 -
Prob. 2.112: Answer should be 454 K
p. 718 -
Problem 3.8: A. 0.04852, B. 0.02536 kg, 0.05997 m3,
C. 0.002316 kg, 2.40 x 10-5 m3
p. 719 -
Answer to Problem 5.80 with revised enthalpies (2856.5 kJ/kg and 2562.2
kJ/kg) is 769.4 m/s.
p. 728 -
Index entry “flowrate” should be “flow rate”
Download