Infinity IMS48
DC Indoor Power Solution
Features / Benefits
• Modular indoor DC power plant
• 100A, 200A, 400A and 600A total capacity
platforms
• LINEAGE POWER high efficiency rectifiers
• LINEAGE POWER Galaxy Pulsar Plus system
controller
• 500mm, 1000mm and 2000mm
standard cabinets
• Flexible DC distribution allowing for breakers,
HRC fuses and custom requirements
• Battery isolation / protection with Low
Voltage Battery Disconnect
• Optional battery shelves
• Optional Non essential load disconnect
• Optional AC distribution features
• Front accessible for installation
and maintenance
INFINITY IMS48 – DC INDOOR POWER SYSTEMS
b+w Electronic Systems
Description
Upon the reconnection of the AC mains supply the rectifiers will ramp up and supply the system loads while
also recharging the batteries.
The INFINITY IMS48 is a range of configurable indoor
DC plant systems utilizing standard flexible building
blocks to provide a high level of modularity.
Correct charging of the batteries with respect to the
ambient temperature is controlled adjusting the float
Voltage of the batteries with respect to the temperature
measured at the battery via thermal probes.
The IMS48 comprises of standard cost effective modules / units each based around common parts to enable
system configuration between 100 Amps and 600
Amps capacity.
Mid battery string Voltage measurement is available as
an option.
This results in competitive system solutions with flexibility to suit individual customer’s needs and short
lead times due to the use of standard parts.
DC Power Configuration
The IMS48 utilises LINEAGE POWER high efficiency
rectifiers along with adaptive rectifier management
software to provide a highly reliable DC power system
with minimal operational costs.
DC power system options are available with a total
capacity of 100A, 200A, 400A and 600A including
system redundancy and battery recharge capability.
The IMS48 incorporates the LINEAGE POWER Galaxy
Pulsar Plus system controller, providing monitoring
and control of system components including rectifiers,
converters, and distribution modules via a multi-drop
RS485 digital communications bus.
System status, parameters, settings, and alarm thresholds can be viewed and configured from the controller’s front panel display.
Assignment and configuration of alarm inputs and
output relays can be performed from a laptop computer or by remote access through a network connection
to the World Wide Web (internet) or your enterprise
network (intranet).
Basic Operation
The INFINITY IMS48 Power System contains all necessary facilities for providing a positive earthed DC supply to Telecommunications Equipment. This DC supply is backed up by batteries located inside the same
cabinet or on external battery stands.
In normal operation the Power System rectifies the AC
mains and provides a positive earthed DC supply to the
loads connected. When the AC-mains fail the loads
are fed from the connected batteries until the battery
voltage has reached a programmable level where the
batteries are disconnected to protect them from damage due to deep-discharge.
Optional contactors in the Power Distribution may disconnect load groups prior to reaching the LVD (Low
Voltage Disconnect) level.
The DC power system comprises of a Power Distribution Unit (PDU), System controller and rectifiers along
with batteries.
The PDU incorporates the DC distribution breakers for
the system loads as well as battery connection and isolation breakers. A contactor is included and current
shunt for monitoring and protection of the batteries
against over charge / discharge.
A second contactor may be installed as an option for
non essential load disconnection in the case of AC
mains failure thereby extending the backup for essential loads.
There are options for additional DC distribution ad AC
distribution depending on specific customer / site
requirements.
All systems include the LINEAGE POWER Galaxy Pulsar Plus system controller providing sophisticated
monitoring and control of not only the DC power system but the capability for complete site management
with options for monitoring door alarms, smoke alarm,
fire suppression equipment control, generator fuel levels as well as customised alarm options.
Communication with the LINEAGE POWER Galaxy
Pulsar Plus system controller may be via front panel
controls, local connection of a lap top or Ethernet
interface – TCP/IP, FTP, Telnet, HTTP, SMTP support.
DC power is provided utilising LINEAGE POWER high
efficiency EPS and CP rectifiers with individual rectifier capacities of 800W, 1800W, 2000W and 2725W.
Power Components
EP0800
Power Distribution Units (PDU)
•
•
•
•
•
•
•
•
• 3U high, 19” module
• DC load distribution,
breakers or fuses.
• Battery connection / isolation
• Low Voltage Battery
disconnect and shunt
• Maintenance bypass switch
• Optional priority and non-priority loads.
• 100A and 200A ratings
800W power output (15A)
Front to back forced air cooled
1U high, 3 rectifiers per shelf
Universal AC input
90% efficient
Digital communication (RS485)
Active Load Current Sharing
Hot pluggable
CP1800/2000/2725
•
•
•
•
•
•
•
•
•
•
CP1800: 1800W (33A) output
CP2000: 2000W (37A) output
CP2725: 2725W (50A) output
Front to back forced air cooled
1U high, 4 rectifiers per shelf
Universal AC input
93% efficient
Digital communication (RS485)
Active Load Current Sharing
Hot pluggable
Load Distribution Units (LDU)
• 3U high, 19” module
• DC load distribution,
breakers or fuses.
• Optional priority and
non-priority loads.
• 200A, 400A and 600A ratings
• Load connection only options (LDU)
Battery Connection module (BATT)
Galaxy Pulsar Plus Controller
High power battery connection units:
• 400A and 600A ratings.
• HRC fuses
• Low Voltage
Battery Disconnect
• Battery current shunt
• Maintenance bypass switch
•
•
•
•
•
•
•
•
•
•
AC connection terminals
• Configurable for Star or Delta AC mains input.
AC Distribution unit option (ADU)
Not included as standard. Options include:
• AC mains isolation switch
• Individual rectifier isolation
• Surge protection
• Service socket
System monitoring and control
Alarm History
Multiple rectifier fail alarms
Battery discharge testing
Battery slope thermal compensation
Battery current monitoring
Optional battery symmetry monitoring
Monitoring of ambient parameters
Customer configurable alarms
SNMP/Ethernet
Cabinets
•
•
•
•
•
•
Indoor type, low weight
600 x 600mm footprint
Top and bottom cable access
Top hoisting points
500, 1000 and 2000mm options
Optional battery shelves each
capable of carrying 1 X 48V string
of 170AH batteries.
• Smaller cabinets can be mounted
on top of each other or a battery rack.
TYPICAL SYSTEM CONFIGURATION
IMS48200 INDOOR CABINET
3U POWER
DISTRIBUTION UNIT
CP RECTIFIER SHELF
PULSAR CONTROLLER
8U RACK SPACE FOR
CUSTOMER LOAD
EQUIPMENTS
BATTERY SHELF
1000mm CABINET
600mm x 600mm
FOOTPRINT
Ordering Information
Please contact your b+w sales representative for pricing,
availability and optional features.
Zur Eisenhütte 11
D-46047 Oberhausen
Tel.
+49 (0) 208 - 850 98-0
Fax
+49 (0) 208 - 850 98-971
E-Mail: bwd@b-w.com
www.b-w.com
b+w Electronic Systems GmbH & Co. KG,
exclusive authorised reseller in EMEA for