UNLEASH THE DRAGON
AMD “Dragon” Platform Technology Performance Tuning Guide
Disclaimer
The information presented in this document is for informational purposes only and may contain
technical inaccuracies, omissions and typographical errors.
The information contained herein is subject to change and may be rendered inaccurate for many
reasons, including but not limited to product and roadmap changes, component and motherboard
version changes, new model and/or product releases, product differences between differing
manufacturers, software changes, BIOS flashes, firmware upgrades, or the like. AMD assumes no
obligation to update or otherwise correct or revise this information. However, AMD reserves the right
to revise this information and to make changes from time to time to the content hereof without
obligation of AMD to notify any person of such revisions or changes.
AMD MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE CONTENTS
HEREOF AND ASSUMES NO RESPONSIBILITY FOR ANY INACCURACIES, ERRORS OR
OMISSIONS THAT MAY APPEAR IN THIS INFORMATION.
AMD SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE. IN NO EVENT WILL AMD BE LIABLE TO ANY
PERSON FOR ANY DIRECT, INDIRECT, SPECIAL OR OTHER CONSEQUENTIAL DAMAGES
ARISING FROM THE USE OF ANY INFORMATION CONTAINED HEREIN, EVEN IF AMD IS
EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
WARNING: AMD and ATI processors are intended to be operated only within their associated
specifications and factory settings. Operating your AMD or ATI processor outside of official AMD or
ATI specifications or outside of factory settings, including but not limited to the conducting of
overclocking (including use of any overclocking guide or software, even if such documentation or
software has been directly or indirectly provided by AMD or otherwise affiliated in any way with AMD),
may damage your processor and/or lead to other problems, including but not limited to, damage to
your system components (including your motherboard and components thereon (e.g. memory));
system instabilities (e.g. data loss and corrupted images); reduction in system performance;
shortened processor, system component and/or system life; and in extreme cases, total
unrecoverable system failure. AMD does not provide support or service for issues or damages
related to use of an AMD or ATI processor outside of official AMD or ATI specifications or outside of
factory settings. You may also not receive support or service from your board or system
manufacturer. Please make sure you have saved all important data before using this overclocking
software. DAMAGES CAUSED BY USE OF YOUR AMD OR ATI PROCESSOR OUTSIDE OF
OFFICIAL AMD OR ATI SPECIFICATIONS OR OUTSIDE OF FACTORY SETTINGS ARE NOT
COVERED UNDER ANY AMD PRODUCT WARRANTY AND MAY NOT BE COVERED BY YOUR
BOARD OR SYSTEM MANUFACTURER’S WARRANTY. SEE THE AMD OVERDRIVE UTILITY
END USER LICENSE AGREEMENT OR THE APPLICABLE AMD OVERCLOCKING UTILITY FOR
DETAILS.
Use of this documentation is subject to the terms and conditions of the AMD OverDrive utility End
User License Agreement. If you have not agreed to the End User License Agreement you do not
have permission to use this guide or the AMD OverDrive software.
2
Introduction
Systems based on the platform technology codenamed “Dragon” may be tuned to deliver
added system performance. The AMD Phenom™ II CPU and the AMD 7-series chipset
motherboards offer an exciting amount of performance tuning options, including potential
overclocking headroom. Note that each processor and chipset is different, and may result in
lower or no overclocking margin.
The critically acclaimed AMD OverDrive™ utility gives users advanced control of system
performance. This utility can be used to fine tune your performance settings in real time with
easy-to-use screens designed for novice to expert users. More details on how to use the
AMD OverDrive utility are included in the “AMD OverDrive utility” section of this guide.
The purpose of this document is to provide detailed information on the various performance
tuning knobs that are present in systems based on the AMD “Dragon” platform technology.
The guide will also offer various suggestions, “tips & tricks” and a comprehensive list of target
clock speeds.
The combination of AMD “Dragon” platform technology, AMD OverDrive utility and optimal,
fine tuned settings can be used to enable truly impressive performance tuning results!
AMD “Dragon” AM3 platform with aggressive cooling solution can enable record breaking benchmark results.
3
Glossary of Terms
HyperTransport™ Reference Clock (HT ref. clk): The base clock for various clock domains on the “Dragon”
platform technology. HT ref. clock is 200MHz by default. CPU, CPU NB, HT Link and Memory clocks are all
linked to HT ref. clock. HT ref. clock adjustment is a good tool for fine tuning the various clocks to optimal
values. The HT ref. clock value itself doesn‟t have any impact on performance.
CPU: Central Processing Unit – the engine of the “Dragon” platform technology. CPU core clock frequency has
the biggest impact on overall performance of the system. It‟s the primary target of tuning.
CPU NB: CPU NorthBridge (should not be confused with NorthBridge chipset, such as AMD 790FX) – part of
the CPU that has its own clock domain and voltage plane. CPU NB clock frequency determines the Memory
controller and L3 cache speed. CPU NB has a notable impact on overall system performance.
CPU FID: CPU Core Clock multiplier. In the case of the Phenom™ II X4 955BE CPU, the default CPU multiplier
is x16 (16x200MHz = 3200MHz). CPU Multiplier can be adjusted on the fly with AMD OverDrive™ utility in
steps of 0.5x. Note that the CPU Multiplier value can be individually adjusted for each of the CPU cores. FID is
unlocked only on the Black Edition CPU models.
CPU NB FID: CPU NB Clock Multiplier. Determines the CPU NB frequency. In the case of the AMD Phenom II
X4 955BE CPU, the default value is x10 (10x200MHz = 2000MHz). CPU NB Multiplier adjustment requires a
reboot (it can not be adjusted on the fly). Can be adjusted in steps of x1. This will also determine the maximum
HT Link multiplier value (i.e. HT Link Multiplier value can not exceed CPU NB Multiplier value). CPU NB and HT
Link multipliers have the same value by default but the CPU NB FID may be increased beyond HT Link value.
Note that FID is unlocked only on the Black Edition CPU models.
HT Link Multiplier: This multiplier determines the clock speed of the HT Link. In the case of the AMD Phenom
II X4 955BE CPU, the default value is x10 (10x200MHz = 2000MHz). In most cases a reboot is required for HT
Link Multiplier value adjustment. The maximum value of HT Link Multiplier is x13 and it can not exceed the CPU
NB Multiplier value. Also note that the HT Link multiplier is unlocked only on the Black Edition CPUs models.
CPU VID: CPU Voltage Identification Digital – a register value that programs the motherboard voltage regulator
(VR) to a specific value. In short, the CPU VID determines the CPU Core Voltage level. In the case of the AMD
Phenom II X4 955BE CPU, the default CPU VID is usually 1.325V or 1.350V. The Maximum CPU VID value is
1.550V. NOTE: VID value may not always equal to the actual voltage level (see “Voltage OFFSET”). VID
value can be adjusted on the fly with AMD OverDrive utility. Note: VID value can be increased only on the Black
Edition CPUs.
CPU NB VID: CPU Voltage Identification Digital – a register value that programs the motherboard voltage
regulator (VR) to a specific value. In short, the CPU NB VID determines the CPU NB Core Voltage level. In the
case of the AMD Phenom II X4 955BE CPU the default CPU NB VID is usually 1.100V. The Maximum CPU NB
VID value is 1.550V. NOTE: VID value may not always equal to the actual voltage level (see “Voltage
OFFSET”). VID value can be adjusted on the fly with the AMD OverDrive™ utility. Note: VID value can be
increased only on the Black Edition CPUs.
4
Glossary of Terms – continued
CPU / CPU NB Voltage OFFSET: Most “Dragon” platform technology motherboards have a BIOS option that
allows Voltage adjustments beyond the CPU VID Voltage range. This voltage offset is added on top of the VID
value. Voltage offset could be negative or positive. Actual voltage level = CPU or CPU NB VID + OFFSET.
Example: VID 1.350V + 0.100V OFFSET = 1.450V actual voltage level.
One of the following options will be available in the BIOS menu (depending on motherboard model):
 “CPU Voltage” and “CPU NB Voltage” item that includes both VID and OFFSET values merged into one
voltage adjustment item (the range can go up to 1.900V)
 Separate items for CPU VID and CPU Voltage – here the “CPU Voltage” value starts from the VID
value and then adds Offset on top of the VID
 CPU and CPU NB “OFFSET” items that control the amount of Voltage offset
In all cases the voltage level can be tuned on the fly with AMD OverDrive utility (VID sliders).
5
AMD OverDrive™ utility
The AMD OverDrive™ utility is a comprehensive utility for performance tuning, system
monitoring and testing. PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES
NOT COVER DAMAGES CAUSED BY RUNNING COMPONENTS OUTSIDE OF
SPECIFICATION.
Download from AMD Game! Website - http://game.amd.com/us-en/drivers_overdrive.aspx?p=1
Advanced Mode
The AMD OverDrive utility is a powerful tool with numerous features and options. However,
in this section we have limited our discussion to only cover the Advanced User mode. The
Advanced User mode of the AMD OverDrive utility allows full control over all the performance
settings. This includes various clock frequency adjustments, clock multiplier settings, voltage
tuning and memory timings.
1
6
2
4
5
3
Figure 1: Screenshot from AMD OverDrive utility.
* AMD is not responsible for damages caused by overclocking (even when overclocking is enabled with AMD OverDrive™ Software). See
disclaimer on page two (2) for more information.
Figure 1, presented above shows all the available clock/voltage tuning options available in
the AMD OverDrive™ utility. The processor, northbridge, PCIe and memory can all be
adjusted to obtain an optimally tuned system.
6
Detailed description of Figure 1 (AMD OverDrive utility screenshot):
Current clock speeds (1)
PCIe® Speed (5)
This section offers real-time monitoring for all the
crucial clock speeds
This item controls the PCIe® clock frequency of the
PCIe® graphics slots. By default this value is 100MHz.
Increasing this value can provide slightly improved 3D
performance.
Target clock speeds (1)
The values under this section are calculated based
on the clock sliders. It is a convenient way to see the
target clock speeds before actually applying the
settings.
CPU Multiplier (2)
The sliders in this section control the CPU multiplier.
In the case of AMD Phenom & AMD Phenom II CPUs
each CPU core has its own multiplier slider (uncheck
“All Cores” checkbox to enable control over individual
CPU cores). In the case of the AMD Phenom Black
Edition CPU the multiplier is unlocked and adjustable.
Target clock speed (1) should be taken into account
when adjusting CPU Multiplier to ensure that the CPU
core clock speed doesn‟t reach unstable value.
HyperTransport™ (HT) reference clock (3)
Almost all the clocks are based on the HT reference
clock (200MHz by default). Therefore adjusting the
HT reference clock will increase the clock speed of
most key components in the system. This includes
CPU core clock, CPU NB clock (Memory controller),
Memory clock and HT clock frequency. Again,
please refer to the “Target Speed” section before
actually applying the HT reference clock adjustment.
In many cases the HT reference clock margin can be
limited by the System Memory clock. If this is the
case, it is a good idea to adjust the System Memory
settings to a lower value from the System BIOS [e.g.
adjust Memclk mode from DDR2-800(400MHz) to
DDR2-667(333MHz) and ensure that 2T timing and
safe, manual memory timings are applied from the
BIOS.]
HyperTransport™ (HT) Link multiplier (3)
This item can be used to adjust the HT Link multiplier
value.
The range of HT Link multiplier depends on the CPU
capabilities: with HT1 generation CPU the slider can
only go up to X5 (1GHz mode), with HT3 generation
of CPUs it can go up to X13 (2.6GHz mode). If HT3
CPU is booted up in HT1 mode (e.g. X5 or lower HT
Link multiplier) it cannot be adjusted to HT3 mode on
the fly. Switching from HT1 to HT3 mode requires a
BIOS adjustment.
Memory Controller multiplier
CPU NB Clock multiplier is not adjustable on the fly.
This item needs to be adjusted from the System
BIOS.
7
CPU Core voltage adjustment (5)
This item can have two sliders: CPU VID and CPU VDDC.
The amount of sliders depends on the motherboard that is
being used. The CPU VID value is limited to max VID value
(1.25V for instance) supported by the CPU. CPU VDDC (or
CPU Vcore Offset) slider can be used to adjust the CPU
Vcore above the max VID value.
Boosting the CPU Vcore voltage can improve the
performance tuning headroom of the CPU Core.
PLEASE NOTE THAT CPU POWER AND THERMAL
REQUIREMENTS INCREASE EXPONENTIALLY WHEN
THE VOLTAGE IS INCREASED. VOLTAGE
ADJUSTMENT IS ALWAYS A RISK AND CAN
DAMAGE THE HARDWARE AND / OR SHORTEN THE
LIFESPAN OF THE CPU OR OTHER COMPONENTS.
System Memory voltage adjustment (5)
This one can also have two sliders (depending on the
motherboard that is being used). “Memory VDDQ”
(memory core voltage) that defaults to 1.8V is the slider
that should be adjusted in most cases. The other slider
(Memory VTT) will adjust automatically according to the
VDDQ slider adjustment. Normally the VTT level should
be 50% of VDDQ level.
Boosting the memory voltage can improve System
memory performance tuning.
PLEASE KEEP IN MIND THAT MEMORY VOLTAGE
ADJUSTMENT IS THE MOST DANGEROUS VOLTAGE
RAIL TO ADJUST AS IT CAN DESTROY NOT ONLY
THE MEMORY BUT ALSO THE CPU AND CAN
POTENTIALLY DAMAGE THE MOTHERBOARD.
ANYTHING BEYOND 2.0V VDDQ IS HAZARDOUS AND
CAN DAMAGE THE CPU AND THE MEMORY
MODULES.
Chipset voltage controls (5)
There are several voltage rails connected to the AMD 7series chipset. The PCIe® bus, HyperTransport™ link and
Chipset core all have separate voltage rails and controls.
Boosting these voltage levels can result in improved
performance tuning margin for these interfaces. For an
example, boosting the HyperTransport™ link voltage by
0.1V can enable higher HT Link frequencies.
Advanced Clock Calibration (6)
ACC is a performance acceleration feature. This feature
can enable greater performance tuning margin for the
AMD Phenom™ Black Edition CPUs. The optimal gain
can be seen in configurations that use high-end CPU
cooling solution in combination with elevated CPU core
voltage (CPU VID) value.
Memory Tuning
1
2
Figure2: AMD OverDrive™ utility Memory Tuning
Memory timing adjustments (1)
Memory Drive strength control (2)
The items circled with red color can directly affect
the overall system performance. Reducing these
values can improve the performance / lower
memory clock tuning margin whereas using higher
values can enable higher memory clock speeds
(but lower clock-to-clock performance).
The lower half of the Memory tuning screen
includes various Drive Strength control items.
PLEASE NOTE THAT SETTING ANY OF THESE
VALUES TO AN INCORRECT / UNSTABLE
VALUE CAN RESULT IN PROGRAM ERRORS
OR SYSTEM CRASH / REBOOT. THE SAFE
DEFAULT SETTINGS WILL BE APPLIED AFTER
REBOOT.
Some of the items are read-only and can only be
adjusted from the System BIOS.
8
Most of these items don‟t have an impact on
performance; however, they can improve Memory
clock tuning margin noticeably in some
configurations.
AN INCORRECT SETTING CAN CAUSE THE
SYSTEM TO CRASH / REBOOT.
AMD OverDrive™ utility Stability Test
The AMD OverDrive™ utility features an impressive system stability assessment. The
“Stability Test” tab under “Performance Control” incorporates AMD‟s CPU test algorithms to
stress the CPUs worst-case scenario. The test consists of various parts that can be set to run
only on a specific CPU core or on all CPU cores. It is also possible to select only specific
tests to run. The amount of time the test will run can also be adjusted with the slider.
Figure 3: AMD OverDrive™ utility Stability Testing
Switching to other tabs in the AMD OverDrive™ utility does not impact the Stability Test. For
instance, the settings under “Performance Control” can be adjusted while running the
Stability Test.
9
AMD “Dragon” platform – Performance Tuning Suggestions
CPU Core Clock Performance Tuning
CPU core clock is the most important item to adjust for the advanced users when tuning the performance of the
system. The CPU Clock speed has a big impact on overall system performance. The following steps explain
how to determine CPU tuning margin.
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED BY
RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE UTILITY).
The key BIOS settings to adjust before proceeding with CPU Performance tuning:




Disable “Cool „n‟ Quiet” –power saving item from the BIOS menu
Disable “C1E” –item from the BIOS menu
Disable “CPU Fan Control” –item from the BIOS menu (allows max cooling)
Ensure that CPU NB, Memory or HT Link values are running at default stable values
The key settings in the Windows® XP or Windows Vista® operating system to adjust before overclocking the
CPU:
 Close all major applications and background tools and save any open documents
 Set OS to “High performance” mode via “Control Panel / Power Options”
 Close any third party hardware / clock monitoring and system information programs
CPU tuning with the AMD OverDrive™ utility:
1)
2)
3)
4)
open AMD OverDrive (“AOD”)
browse to “Preference” tab and set the application from “Novice” mode to “Advanced” mode
enter the “Clock / Voltage” –tab under the “Performance Control” section
the two key sliders are “CPU Core Multiplier” and “CPU VID” – monitor the “Target speed” values
before applying them. Make sure that “Select all cores” is checked
5) increase the values in small steps (example: set CPU Multiplier from x15 to x16 and CPU VID from
1.350V to 1.400V)
rd
6) verify stability of the new settings with AOD Stability test or with 3 party multithreaded benchmark
(Cinebench 95 or 10 for example) or stress tester (OCCT) before increasing the CPU Multiplier or VID
values to the next level. Note that the stress tester must be able to fully stress all CPU cores.
Please refer to “AMD “Dragon” Platform Technology Performance Tuning Targets” for the expected / optimal
Multiplier and VID values.
10
Advanced CPU Core Tuning
There are a few additional items in the AMD OverDrive™ utility that can be used to improve the CPU tuning
margin in some cases.
1) Individual Core Control
In this section the goal is to determine the performance potential of each CPU core individually. In
contrast in the previous section we determined the maximum CPU Core clock that can be successfully
applied to all CPU cores.
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).
Uncheck the “Select All Cores” item in the “AMD OVERDRIVE UTILITY Clock / Voltage” tab to enable
the control over individual CPU core multiplier sliders. It is now possible to determine the performance
potential of each individual CPU core by following the steps that were listed in the previous section.
Find out the maximum stable value for each CPU core. Certain CPU cores performance may be
improved more than others.
HT reference clock slider can be used for finer control over the CPU Core clock. 1MHz HT reference
clock steps are available. This translates to 10-30MHz CPU Core clock steps depending on the CPU
Multiplier used.
11
2) Advanced Clock Calibration
In case of the AMD Phenom II CPU, the “Advanced Clock Calibration” (ACC) feature can be used to
improve the tuning margin of specific CPU cores. Typically the CPU core that has the lowest tuning
margin by default is the likely candidate to see benefit from ACC-feature.
ACC can be enabled thru the AMD OverDrive™ utility or from the BIOS menu. Select the “Per Core”
option and set the value of ACC to “+2%” for the CPU Core that has the least amount of headroom. Set
the rest of the CPU cores to “0%” (default value).
Note that the system needs to be restarted before the new settings will be applied. Restarting the
system is required each time the value(s) of ACC are adjusted.
CPU NorthBridge Performance Tuning
The CPU NorthBridge (CPU NB) clock speed determines the efficiency and bandwidth capacity of the Memory
controller. L3 cache runs at this frequency as well. CPU NB performance tuning gives a measurable boost for
overall system performance. In particular it can reduce the Memory latency and improve L3 cache bandwidth
and latency. In some scenarios the CPU NB should be tuned in order to take the full advantage of overclocked
Memory frequency and bandwidth. In general the CPU NB clock should be at least three times the Memory
clock (example in case of DDR3-1600: 3 x 800MHz = 2400MHz NB clock).
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).
In terms of power delivery and voltage regulation the latest AM2+ and AM3 motherboards have a dedicated
power plane for the CPU NB Voltage rail. The voltage level of CPU NB power plane (CPU NB VID) can be set
independently from the CPU Core Voltage rail (CPU VID).
The frequency of CPU NB is determined by the CPU NB Multiplier (CPU NB FID) and by the HT reference clock
(HT ref. clock, 200MHz by default). CPU NB Multiplier can not be changed on the fly (as various memory
parameters and memory training is based on the NB clock value). A reboot is required in order to adjust the
CPU NB Multiplier. Therefore the performance tuning of CPU NB is mostly done thru the BIOS menu. Note that
CPU NB Multipliers are integer values and therefore the adjustment will be in steps of 200MHz or more
(depending on HT ref clock value). The combination of “HT ref clock” and the “CPU NB Multiplier” adjustment in
the BIOS menu will allow finer steps.
HT reference clock adjustments can be done on the fly via the AMD OverDrive™ utility and this allows finer
granularity for CPU NB Performance tuning and may reduce the time required for tuning (as there is no need to
reboot the system between different HT ref. clock values).
12
CPU NB performance tuning with AMD OverDrive™ utility (HT ref. clock):
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).

Set CPU NB and HT Link multiplier to known good values (example: default, 1800MHz or x9)

Set CPU Core Multiplier(s) / Voltage to a known stable setting before proceeding with CPU NB
performance tuning (to ensure that CPU core doesn‟t cause stability issues / crashes)

Set Memory clock and timings to known stable settings (example: DDR3-1333 CL9-9-9 for AM3 or
DDR2-800 CL5-5-5-15-2T for AM2+), note that Memory interface will also be overclocked when HT ref.
clock is adjusted. Memory must be able to run 10% above default clock during the CPU NB tests. Set
Memory to DDR3-1333 or DDR3-1067 mode (DDR2-800 or DDR2-667MHz mode for DDR2 / AM2+)
and boost Memory voltage to 1.600V (1.90V for DDR2 / AM2+) to ensure stability

Adjust “HT ref. clock” slider in AOD (2MHz steps for accuracy, 5MHz steps for less accurate but faster
results)

Run a stability test before increasing the HT ref. clock to another level

Adjust CPU NB VID voltage slider in AOD if there were any stability issues (in 0.050V steps – if a boost
of 100mV doesn‟t provide any improvement for stability then the limit has been found)

Once the CPU NB clock has been increased by 200MHz (the next step available via CPU NB Multiplier
change) while maintaining good stability, reboot and enter the BIOS menu in order to increase the NB
Multiplier (see the next section)
13
CPU NB performance tuning through the BIOS menu:

Set the CPU NB clock speed up to the next available value (example: if 1800MHz / x9 is the default and
NB clock testing via AMD OverDrive utility was OK at 2000MHz then set CPU NB BIOS item to
2000MHz / x10 now)

Set CPU NB Voltage to a known stable value (based on the NB clock testing done thru AMD OverDrive
utility)

Keep HT Link multiplier at default value (example: 1800MHz or x9 in case of the AMD Phenom II
X4 940BE CPU)

Set CPU Core Multiplier(s) / Voltage to a known stable setting before proceeding with CPU NB
performance tuning (to ensure that CPU core doesn‟t cause stability issues / crashes)

Set Memory clock and timings to known stable settings (example: DDR3-1333 CL9-9-9 for AM3 or
DDR2-800 CL5-5-5-15-2T for AM2+), note that Memory interface will also be overclocked when HT ref.
clock is adjusted. Memory must be able to run 10% above default clock during the CPU NB tests. Set
Memory to DDR3-1333 or DDR3-1067 mode (DDR2-800 or DDR2-667MHz mode for DDR2 / AM2+)
and boost Memory voltage to 1.600V (1.90V for DDR2 / AM2+) to ensure stability

Reboot the system with the new CPU NB Multiplier / Voltage value and continue HT ref. clock testing
thru AMD OverDrive™ utility (as instructed in the previous section)
The alternative approach is to adjust everything directly from the BIOS menu and utilize a bootable stand-alone
stability tester such as Memtest86 or Memtest86+ (may be installed on a bootable USB key).
Please refer to “AMD “Dragon” Platform Technology Performance Tuning Targets” for the expected / optimal
Multiplier and VID values.
NOTE: CPU NB Multiplier value can not be increased above the default value unless an unlocked AMD
Phenom II Black Edition CPU is used.
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).
14
Memory Performance tuning – AM3 / DDR3
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).
Memory clock speed is tied to HT ref. clock with certain ratios. The following Memory clock modes are
available on the AMD “Dragon” AM3 DDR3 platform technology:




DDR3-800 (400MHz) – 2:1 ratio
DDR3-1066 (533MHz) – 8:3 ratio
DDR3-1333 (667MHz) – 10:3 ratio
DDR2-1600 (800MHz) – 4:1 ratio
In the case of AM3 DDR3 platform, there are two key strategies for Memory tuning:
1) utilize DDR3-1600 Memclk mode (800MHz) with CL7-7-7…CL9-9-9 timings (depending on the DIMM
specification and headroom) and minor HT ref. clock boost (below 225MHz)
2) utilize DDR3-1333 Memclk mode (667MHz) with faster CL5-5-5…CL7-7-7 timings and HT ref. clock
boost (the amount of HT ref. clock boost will depend on the DIMM OC headroom)
Option #1 is easier and works in most cases, offering the optimal amount of memory bandwidth and latency.
Option #2 could enable the absolute highest Memory performance depending on memory modules but may
require more manual tuning. Option #2 could be optimal when using DRAM modules capable of CL6-6-6
timings at DDR3-1600 speeds.
The optimal memory voltage will depend on the DIMMs. In general there are two DDR3 DIMM categories: high
voltage DIMMs that run best at 1.85…2.05V and low voltage DIMMs that prefer 1.6…1.7V.
The optimal Tras and Trc timing parameter value is calculated as follows:
Tras = Tcl + Trcd + Trp
Example: Tras should be set to 21 in case of CL7-7-7 -settings
Trc = Tras + Tcl
Example: Trc should be set to 28 in case of CL7 + Tras = 21 -settings
Enabling 2T –timing mode can improve stability with 4GB or 8GB memory configurations (but will cause a slight
performance hit).
The Memory controller of AMD Phenom and AMD Phenom II CPUs can be set to run in Ganged mode or in
Unganged mode. Ganged mode means that there is a single 128bit wide dual-channel DRAM Controller (DCT)
enabled. Unganged mode enables two 64bit wide DRAM Controllers (DCT0 and DCT1).
The recommended setting in most cases is the Unganged memory mode. Ganged mode may allow slightly
higher Memory performance tuning and performs well in single-threaded benchmarks.
Depending on the motherboard and BIOS, it may be required manually setting the timing parameters for each
DCT (in Unganged mode) when performance tuning the memory or fine tuning the timings. Some BIOS
versions apply the same timings automatically for both DCTs in an Unganged mode.
The DIMM slots furthest away from the CPU socket should be equipped first (usually marked as DIMM slot 2&3
or A2&B2).
15
Memory Performance tuning – AM2+ / DDR2
Memory clock speed is tied to HT ref. clock with certain ratios. The following Memory clock modes are
available on the AMD “Dragon” AM2+ DDR2 platform technology:





DDR2-400 (200MHz) – 1:1 ratio
DDR2-533 (266MHz) – 4:3 ratio
DDR2-667 (333MHz) – 5:3 ratio
DDR2-800 (400MHz) – 2:1 ratio
DDR2-1066 (533MHz) – 8:3 ratio
When HT ref. clock value is increased beyond the default 200MHz then the Memory clock value will also
increase depending on the Memory clock mode and the ratio selected.
Example: 210MHz HT ref. clock and DDR2-667 memclk mode will result in 350MHz (DDR2-700) memory clock
speed (210 x 5 / 3 = 350MHz)
In case of Dragon AM2+ DDR3 platform, there are two key strategies for Memory tuning:
3) utilize DDR2-1066 Memclk mode (533MHz) with CL4/5-5-5-15-2T timings and minor HT ref. clock boost
(below 225MHz)
4) utilize DDR2-800 or 667 Memclk mode (400 or 333MHz) with faster CL4-4-4-12 timings and noticeable
HT ref. clock boost (above 250MHz)
Option #1 is easier and works in most cases offering the optimal amount of memory bandwidth and latency.
Option #2 could enable the absolute highest Memory performance depending on memory modules but requires
more manual tuning and usually higher voltage levels. Option #2 could be optimal when using DRAM modules
capable of CL4-4-4 timings at DDR2-1200 speeds.
It‟s important to turn on the “2T mode” from the BIOS when testing with DDR2-800 and DDR2-667 modes with
higher HT ref. clock value.
16
HyperTransport™ (HT) reference clock
HT reference clock value has no direct impact on system performance. Therefore the maximum amount of HT
reference clock tuning is not required in order to get the highest performance. HT ref. clock can be used to fine
tune and dial in the other key clock values on the AMD “Dragon” platform technology. In some cases a relatively
high (over 250MHz) HT reference clock might be required for optimal performance. The role of HT reference
clock margin becomes critical in particular with multiplier locked CPUs.
In general it‟s a good idea to test how high the HT reference clock can be pushed. This is a useful data point to
have when performance tuning the system (even an unlocked CPU).
PLEASE NOTE THAT THE AMD PRODUCT WARRANTY DOES NOT COVER DAMAGES CAUSED
BY RUNNING COMPONENTS OUTSIDE OF SPECIFICATION INCLUDING DAMAGES CAUSED BY
OVERCLOCKING (EVEN WHEN OVERCLOCKING IS ENABLED WITH THE AMD OVERDRIVE
UTILITY).
1) Configure CPU, CPU NB, Memory mode, Memory timings (2T mode) and HT Link multiplier to values
that allow good margin for HT reference clock overclocking
o The mentioned clock domains must be able to run at least 20% higher than the specified
multiplier / memclk mode
o This is to ensure that HT ref. clock margin testing is not limited by the other components
2) Load OS and start AMD OverDrive utility
3) Start the AMD OverDrive utility stability tester
4) Adjust HT reference clock slider in 2MHz steps until the system hangs
5) Enter the BIOS menu and set HT ref. clock to a value that is a bit lower than the value that previously
failed (example: if 260MHz failed in AMD OVERDRIVE utility, then set BIOS to 255MHz)
o Check that CPU, CPUNB, HT Link and Memory are still at safe values after the HT ref. clock
change. Reduce multiplier values as needed
6) Return to step #2 and repeat until the maximum HT reference clock value is found
Please refer to “AMD “Dragon” Platform Technology Performance Tuning Targets” for the expected HT ref.
clock tuning margin.
HyperTransport™ (HT) Link frequency
HyperTransport Link frequency will determine the available bandwidth between the CPU and the NorthBridge
Chipset (such as AMD 790FX). In most single CPU socket configurations the default 1.8GHz or 2GHz HT Link
value offers sufficient amount of bandwidth even for multi-GPU configurations. Increasing HT Link frequency
may provide a small performance boost for certain 3D applications, games and benchmarks.
Similar to CPU and CPU NB clock, the HT Link frequency is tied to HT reference clock (increase in HT ref. clock
will increase the HT Link frequency). Multiplier values from x1 thru x13 are available in case of an unlocked
AMD Phenom II Black Edition CPU. It is possible to tune the HT Link frequency by adjusting the HT Link
multiplier to a higher value and / or by increasing the HT reference clock.
Note that HT Link multiplier value can not exceed the CPU NB Multiplier value and that CPU HT Link multiplier
is locked in case of a locked, non-Black Edition AMD Phenom II CPU.
17
“Dragon” Platform Technology – Performance Tuning Targets
The following table lists some possible results for an unlocked AMD Phenom II Black Edition CPU as well as the
optimal voltage values for most “Dragon” platform technology systems.
Note that these results are strictly estimates based on overclocking data from a limited sample size. The actual
results will vary depending on the CPU, motherboard, cooling solution and memory modules used in the tests.
The “air cooling” column and the suggested Voltage and Frequency values are based on the assumption that a
high-end heatsink and fan is used.
The “extreme” column lists the suggested Voltage settings and expected target Frequency values for Liquid
Nitrogen (LN2) cooling solution (-196C).
Item
CPU Core clock
CPU NB clock
HT Link clock
DDR3 Memory clock
DDR2 Memory clock
HT reference clock
Voltage
air cooling
extreme
1.35 - 1.50V
1.35 - 1.50V
1.20 - 1.35V
1.80 - 2.00V
2.0 - 2.3V
NA
1.65 - 1.85V
1.40 - 1.55V
1.20 - 1.40V
1.90 - 2.10V
2.0 - 2.3V
NA
Frequency
air cooling
extreme
3800 - 4100MHz
2800 - 3000MHz
(1
1000 - 2700MHz
5600 - 6300MHz
3900 - 4600MHz
(1
1000 - 3000MHz
1700 - 1850MHz
1150 - 1200MHz
280 - 330MHz
1700 - 1900MHz
1175 - 1225MHz
300 - 400MHz
1. HT Link speed of 1.6-2.0GHz offers optimal amount of bandwidth and stability for nearly all single
socket configurations. Setting HT Link mode to x5 (1GHz) can improve stability under LN2 cooling.
18
ATTRIBUTION
© 2009 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD Arrow logo, ATI,
the ATI logo, AMD Phenom, AMD OverDrive and combinations thereof are trademarks of
Advanced Micro Devices, Inc. HyperTransport is a licensed trademark of the HyperTransport
Technology Consortium. PCIe is a registered trademark of PCI-SIG. Windows and Windows
Vista are registered trademarks of Microsoft Corporation. Other names are for informational
purposes only and may be trademarks of their respective owners.
19