WHEEL LOADERS
LW110.B
Specifications
www.newhollandconstruction.com
LW110.B Specifications
LW110.B DIMENSIONS
40°
45°
K
N
J
L
B
I
A
O°
F
E°
C
P
D
M
A. Height to top of cab..................................................125″ (3175 mm)
B. Height to top of exhaust........................................112.8″ (2865 mm)
C. Height to drawbar......................................................37.4″ (950 mm)
D. Wheelbase .............................................................108.3″ (2750 mm)
E. Rear departure angle .....................................................................34°
G
H
Turning radius-outside of tires...................................194.8″ (4947 mm)
F. Ground clearance ......................................................14.9″ (377 mm)
G. Tread width..............................................................72.8″ (1850 mm)
H. Width over tires.......................................................92.1″ (2339 mm)
LW110.B Specifications
PERFORMANCE DATA Pin-On Buckets
KEY Bucket Type/Size
General Purpose
w/Bolt-on Edge
General Purpose w/
Teeth and Segments
General Purpose
w/Bolt-on Edge
General Purpose w/
Teeth and Segments
Stockpiling
w/Bolt-on Edge
Capacity, heaped (SAE)
2.0 yd3 (1.5 m3)
2.0 yd3 (1.5 m3)
2.25 yd3 (1.7 m3)
2.25 yd3 (1.7 m3)
2.5 yd3 (1.9 m3)
Capacity, struck (SAE)
1.7 yd3 (1.3 m3)
1.7 yd3 (1.3 m3)
1.9 yd3 (1.47 m3)
1.9 yd3 (1.47 m3)
2.1 yd3 (1.62 m3)
Bucket width
97.2″ (2468 mm)
97.2″ (2468 mm)
97.2″ (2468 mm)
97.2″ (2468 mm)
97.2″ (2468 mm)
Bucket Weight
1556 lb. (706 kg)
1622 lb. (736 kg)
1639 lb. (744 kg)
1707 lb. (774 kg)
1577 lb. (715 kg)
Breakout force
20,947 lb. (93.2 kN)
20,881 lb. (92.9 kN)
19,388 lb. (86.2 kN)
19,319 lb. (85.9 kN)
18,194 lb. (80.9 kN)
Tipping load, straight
18,091 lb. (8206 kg)
18,005 lb. (8167 kg)
17,887 lb. (8114 kg)
17,799 lb. (8073 kg)
17,882 lb. (8111 kg)
Tipping load @ 40° full turn
15,777 lb. (7156 kg)
15,691 lb. (7117 kg)
15,589 lb. (7071 kg)
15,500 lb. (7031 kg)
15,590 lb. (7072 kg)
Dump clearance, 45°
dump angle-full height
109.2″ (2773 mm)
105.3″ (2675 mm)
107.2″ (2723 mm)
103.4″ (2625 mm)
105.4″ (2677 mm)
Reach, 45° dump angle, full height 37.6″ (955 mm)
41.6″ (1057 mm)
39.6″ (1006 mm)
43.6″ (1107 mm)
41.3″ (1049 mm)
Reach, 45° dump angle,
7-ft. (2.13 m) height
55.9″ (1420 mm)
57.8″ (1469 mm)
56.9″ (1445 mm)
58.7″ (1491 mm)
57.6″ (1463 mm)
Max. Reach, bucket and
loader arms level
81.8″ (2077 mm)
87.7″ (2226 mm)
84.6″ (2148 mm)
90.5″ (2297 mm)
87.0″ (2209 mm)
Overall height, bucket
@ full height
181.3″ (4604 mm)
181.3″ (4604 mm)
184.4″ (4684 mm)
184.4″ (4684 mm)
186.5″ (4738 mm)
L
Hinge pin height, fully raised
142.1″ (3608 mm)
142.1″ (3608 mm)
142.1″ (3608 mm)
142.1″ (3608 mm)
142.1″ (3608 mm)
M
Overall length, bucket on ground 258.4″ (6563 mm)
264.3″ (6712 mm)
261.3″ (6638 mm)
267.2″ (6787 mm)
264.1″ (6708 mm)
N
Clearance circle, bucket @ carry 428.1″ (10,873 mm)
431.5″ (10,959 mm)
429.8″ (10,916 mm)
433.2″ (11,004 mm)
431.4″ (10,957 mm)
Hydraulic Lifting Capacity
@ Full Height
12,353 lb. (5603 kg)
12,287 lb. (5573 kg)
12,268 lb. (5565 kg)
12,201 lb. (5534 kg)
12,330 lb. (5593 kg)
Hydraulic Lifting Capacity
@ Max. Reach
17,077 lb. (7746 kg)
17,011 lb. (7716 kg)
16,977 lb. (7701 kg)
16,908 (7669 kg)
17,027 lb. (7723 kg)
Hydraulic Lifting Capacity
@ Ground Level
23,895 lb. (10,839 kg) 23,903 lb. (10,842 kg) 22,096 lb. (10,023 kg) 22,091 lb. (10,020 kg) 20,976 lb. (9515 kg)
Max. dump angle @ full height
50°
50°
50°
50°
50°
Max. Rollback @ full height
54°
54°
54°
54°
54°
Max. Rollback @ max. reach
52°
52°
52°
52°
52°
Max. Rollback @ carry
43°
43°
43°
43°
43°
Max. Rollback @ ground
40°
40°
40°
40°
40°
Digging depth
2.5″ (64 mm)
2.9″ (74 mm)
2.8″ (70 mm)
3.2″ (80 mm)
3.1″ (78 mm)
Operating weight
22,915 lb. (10,394 kg) 22,981 lb. (10,424 kg) 22,998 lb. (10,432 kg)
I
J
K
O
P
23,065 lb. (10,462 kg) 22,936 lb. (10,403 kg)
ADJUSTMENTS TO OPERATING WEIGHTS AND TIPPING LOADS WITH PIN-ON BUCKETS
Add (+) or deduct (-) lb. (kg) as indicated
For loader with:
Operating Weight
Tipping Load, Straight
Tipping Load, 40° Full Turn
17.5x25 12 ply L2 .................................-428 lb. (-194 kg).................................-312 lb. (-142 kg).................................-277 lb. (-125 kg)
17.5x25 12 ply L3 .................................-220 lb. (-100 kg) .................................-160 lb. (-73 kg)...................................-142 lb. (-65 kg)
17.5R25 XHA TL, 1 pc. rim...................-64 lb. (-29 kg) .....................................-46 lb. (-21 kg) ....................................-42 lb. (-19 kg)
17.5R25 XHA TL, 3 pc rim....................+224 lb. (+102 kg)................................+164 lb. (+74 kg)..................................+144 lb. (+65 kg)
17.5R25 GP-2B TL................................+172 lb. (+78 kg)..................................+126 lb. (+57 kg)..................................+111 lb. (+50 kg)
Note: Specification data is based on loader equipped with 17.5R25 (16 ply) XTLA Michelin radial tires, ROPS cab with heater & A/C, auxiliary steering, front and rear
fenders, full fuel, 175 lb. operator. Specifications per ISO 13497 unless otherwise noted.
LW110.B Specifications
PERFORMANCE DATA Coupler Buckets
KEY Bucket Type/Size
I
TRANSMISSION
Excavating
w/Bolt-on Edge
Excavating w/Teeth
and Segments
General Purpose
w/Bolt-on Edge
General Purpose w/
Teeth and Segments
4-in-1
w/Bolt-on Edge
Capacity, heaped (SAE)
2.0 yd3 (1.5 m3)
2.0 yd3 (1.5 m3)
2.25 yd3 (1.7 m3)
2.25 yd3 (1.7 m3)
1.75 yd3 (1.32 m3)
Capacity, struck (SAE)
1.7 yd3 (1.3 m3)
1.7 yd3 (1.3 m3)
1.96 yd3 (1.50 m3)
1.96 yd3 (1.50 m3)
1.52 yd3 (1.16 m3)
Bucket width
97.2" (2468 mm)
97.3" (2472 mm)
97.2" (2468 mm)
97.3" (2472 mm)
97.2" (2468 mm)
Bucket weight with coupler
2335 lb. (1059 kg)
2405 lb. (1091 kg)
2542 lb. (1153 kg)
2610 lb. (1184 kg)
3177 lb. (1441 kg)
Breakout force
16,685 lb. (74.2 kN)
16,916 lb. (75.2 kN)
15,811 lb. (70.3 kN)
15,897 lb. (70.7 kN)
17,949 lb. (79.8 kN)
Tipping load, straight
16,366 lb. (7423 kg) 16,304 lb. (7395 kg) 16,281 lb. (7385 kg) 16,215 lb. (7355 kg) 15,284 lb. (6933 kg)
Tipping load @ 40° full turn
14,184 lb. (6434 kg) 14,122 lb. (6406 kg) 14,099 lb. (6395 kg) 14,033 lb. (6365 kg) 13,158 lb. (5968 kg)
Dump clearance,
45° dump angle-full height
103.7″ (2634 mm)
100.3″ (2547 mm)
101.6″ (2580 mm)
100.3″ (2547 mm)
100.9″ (2564 mm)
Reach, 45° dump angle, full height 44.2″ (1122 mm)
47.7″ (1211 mm)
45.1″ (1145 mm)
47.7″ (1211 mm)
35.4″ (900 mm)
Reach, 45° dump angle,
7-ft. (2.13 m) height
59.4″ (1510 mm)
60.8″ (1544 mm)
59.0″ (1500 mm)
60.8″ (1544 mm)
49.0″ (1244 mm)
Max. Reach, bucket and
loader arms level
90.0″ (2288 mm)
95.9″ (2377 mm)
92.1″ (2339 mm)
98.0″ (2488 mm)
86.3″ (2193 mm)
Overall height, bucket
@ full height
186.1″ (4727 mm)
186.1″ (4727 mm)
193.7″ (4919 mm)
193.7″ (4919 mm)
186.8″ (4745 mm)
L
Hinge pin height, fully raised
142.0″ (3607 mm)
142.0″ (3607 mm)
142.0″ (3607 mm)
142.0″ (3607 mm)
142.0″ (3606 mm)
M
Overall length, bucket on ground 266.6″ (6772 mm)
271.8″ (6904 mm)
269.5″ (6845 mm)
275.0″ (6984 mm)
266.0″ (6757 mm)
N
Clearance circle, bucket @ carry 432.8″ (10,994 mm) 436.2″ (11,079 mm) 434.6″ (11,039 mm) 438.2″ (11,130 mm) 432.7″ (10,990 mm)
J
K
O
P
Hydraulic Lifting Capacity
@ Full Height
11,563 lb. (5245 kg) 11,493 lb. (5213 kg) 11,356 lb. (5151 kg) 11,288 lb. (5120 kg) 10,718 lb. (4862 kg)
Hydraulic Lifting Capacity
@ Max. Reach
16,201 lb. (7349 kg) 16,132 lb. (7317 kg) 15,975 lb. (7246 kg) 15,907 (7215 kg)
Hydraulic Lifting Capacity
@ Ground Level
16,171 lb. (7335 kg) 16,240 lb. (7366 kg) 14,733 lb. (6683 kg) 14,777 lb. (6703 kg) 15,049 lb. (6826 kg)
Max. dump angle @ full height
50°
50°
50°
50°
50°
Max. Rollback @ full height
54°
54°
54°
54°
54°
Max. Rollback @ max. reach
52°
52°
52°
52°
52°
Max. Rollback @ carry
43°
43°
43°
43°
43°
Max. Rollback @ ground
40°
40°
40°
41°
43°
Digging depth
2.5″ (63 mm)
2.9″ (73 mm)
3.5″ (89 mm)
3.9″ (99 mm)
6.3″ (160 mm)
Operating weight
23,694 lb. (10,747 kg) 23,764 lb. (10,779 kg) 23,901 lb. (10,841 kg) 23,969 lb. (10,872 kg) 24,536 lb. (11,129 kg)
15,332 lb. (6955 kg)
ADJUSTMENTS TO OPERATING WEIGHTS AND TIPPING LOADS WITH COUPLER BUCKETS
Add (+) or deduct (-) lb. (kg) as indicated
For loader with:
Operating Weight
Tipping Load, Straight
Tipping Load, 40° Full Turn
17.5x25 12 ply L2 .................................-428 lb. (-194 kg).................................-297 lb. (-135 kg).................................-262 lb. (-119 kg)
17.5x25 12 ply L3 .................................-220 lb. (-100 kg) .................................-152 lb. (-69 kg)...................................-135 lb. (-61 kg)
17.5R25 XHA TL, 1 pc. rim...................-64 lb. (-29 kg) .....................................-44 lb. (-20 kg) ....................................-39 lb. (-18 kg)
17.5R25 XHA TL, 3 pc rim....................+224 lb. (+102 kg)................................+156 lb. (+71 kg)..................................+137 lb. (+62 kg)
17.5R25 GP-2B TL................................+172 lb. (+78 kg)..................................+120 lb. (+54 kg)..................................+105 lb. (+48 kg)
Note: Specification data is based on loader equipped with 17.5R25 (16 ply) XTLA Michelin radial tires, ROPS cab with heater & A/C, auxiliary steering, front and rear
fenders, full fuel, 175 lb. operator. Specifications per ISO 13497 unless otherwise noted.
LW110.B Specifications
ENGINE
HYDRAULIC SYSTEM/STEERING
Make and Model................New Holland 445T/M2, EPA Tier 2 certified
Pump (steering/implement) .........Variable-displacement, piston pump
Cylinders .............................................................................................4
Maximum flow ..........................35.4 gpm (134 L/m) @ 2000 rpm and
2750 psi (18961 kPa)
Displacement............................................................275 cu. in. (4.5 L)
Bore x Stroke.................................4.09″ (104 mm) x 5.20″ (132 mm)
Power - Rated .......................................................................................
Gross (per SAE J1995)......................119 hp (89 kW) @ 2,000 rpm
Net (per SAE J1349)......................110 hp (82 kW) @ 2,000 rpm
Pressure .....................................Loader relief: 3625 psi (25,000 kPa);
Steering relief: 3500 psi (24,132 kPa)
Valves ...................................Closed-center, load sensing; positive low
pressure regeneration for bucket dump
Torque Rise ...................................................................................14%
Loader controls .......................Standard two-function valve; single- or
dual-lever controls, optional third-function valve;
with auxiliary lever, pilot operated controls
with electromagnetic detents for float,
raise, and bucket rollback; control lockout
Fuel Injection......................................................Direct injection, diesel
Hydraulic cycle times
Torque - Peak........................................................................................
Gross (per SAE J1995) .............355 lb.-ft. (481 N-m) @ 1,400 rpm
Net (per SAE J1349) .............336 lb.-ft. (455 N-m) @ 1,400 rpm
Fuel Filter.....................................................Full-flow spin-on cartridge
Raise-loaded.........................................................................5.6 sec.
Lube System........Full-flow spin-on filter cartridge with integral cooler
Dump-loaded........................................................................1.1 sec.
Aspiration .............................................Turbocharged, air to air cooled
Lower-empty, power down...................................................3.7 sec.
Air Cleaner ..........Dry type elements with warning restriction indicator
Lower-empty, float down......................................................2.7 sec.
Advanced Cooling System......Independent mounted coolers, mid-mounted
STEERING
Fan ..............Hydraulically driven suction fan, 28″ (711 mm) diameter,
purge feature (optional)
Type ........Hydraulic orbital, load sensing, 40° center pivot articulation
Radiator .....................................................................5 rows, 9 fins/in.
Filtration .................10 –micron, full flow cartridge filter on return line
HYDRAULIC CYLINDERS
TRANSMISSION
Type ..............................................................Countershaft, power shift
Torque Converter ...........Single-phase, single-stage, 2.549:1 stall ratio
Shift Control System ...................................Electronic control module,
torque sensing, manual or automatic shifting
Control location..........Steering column-mounted twist-grip shift lever,
auxiliary controls on loader joystick
Travel speeds with 17.5x25 L2/L3 tires
Forward
Lift Cylinders, bore x stroke x rod..............................4.0″ (102 mm) x
30.8″ (783 mm) x 2.25″ (57 mm)
Dump Cylinder, bore x stroke x rod............................4.5″ (114 mm) x
20.8″ (529 mm) x 2.5″ (64 mm)
Steering Cylinders, bore x stroke x rod .........................2.5″ (64 mm) x
18.2″ (462 mm) x 1.4″ (35 mm)
SERVICE CAPACITIES
Reverse
Gear 1...................4.3 mph (6.9 km/h) .........4.5 mph (7.2 km/h)
Gear 2...................8.3 mph (13.3 km/h) .......8.7 mph (14.0 km/h)
Gear 3...................14.5 mph (23.4 km/h) .....15.2 mph (24.5 km/h)
Gear 4...................23.4 mph (37.6 km/h)
AXLES/BRAKES
Fuel tank.....................................................................50.0 gal. (189 L)
Engine oil .......................................................................12 qt. (11.4 L)
Engine oil with filter .......................................................13 qt. (12.3 L)
Transmission with filter ...............................................5.0 gal. (18.9 L)
Cooling system...............................................................5.8 gal. (22 L)
Hydraulic reservoir ....................................................15.0 gal. (56.8 L)
Hydraulic system.....................................................30.0 gal. (113.6 L)
Axles (total), each ..........................................................23.2 qt. (22 L)
Differentials ................................................Limited slip, front and rear
Final drives..........................Heavy-duty out board planetary reduction
LW110.B BUCKET SELECTION CHART WITH FILL FACTORS
Brakes
Service brakes ........Outboard, hydraulically actuated, maintenance-free,
multiple wet disc with accumulator, acting on all
four wheels. Complies with SAE J1473 and ISO 3450.
Parking brake........................Spring applied, hydraulically released,
acting on transmission output shaft
ELECTRICAL
Electrical system .......24 volt, negative ground with 70-amp alternator
Batteries (two 12 volt) ...............................................700 CCA; 170 Ah
Material density (lb./yd3)
Rear axle oscillation.........................24 degrees total, 30.8″ (782 mm)
maximum vertical travel at wheel
4700
4500
4300
4100
3900
3700
3500
3300
3100
2900
2700
2500
———————————————————————————
———————————————————————————
95%
———————————————————————————
———————————————————————————
———————————————————————————
95%
100%
———————————————————————————
115%
———————————————————————————
95%
100%
———————————————————————————
115%
———————————————————————————
100%
———————————————————————————
115%
———————————————————————————
———————————————————————————
2
2.25
2.5
Bucket Capacity, Heaped (Cubic Yard)
LW110.B Specifications
STANDARD EQUIPMENT
ENGINE
New Holland 445T/M2 4-cylinder turbo
diesel
EPA off-road certified, Tier 2
Displacement: 275 cu in (4.5 L)
Horsepower (kilowatts):
Gross 119hp (89 kW) @ 2000 rpm
Net 110hp (82 kW) @ 2000 rpm
Air-to-air after cooler
Anti-freeze solution -34°F (-37°C)
Air cleaner - 2 stage w/radial seal
elements
Hydraulically driven suction fan w/ guard
Advanced Cooling System (ACS)
AXLES & TIRES
Limited slip differentials - front and rear
Maintenance free driveshafts
Axle dipsticks
Wheels, 1-pc rims
TRANSMISSION
Speeds: 4F-3R
Computer controlled, full-power,
proportional shifting
Single lever electronic shift control
Programmable gear selection
Selectable fully-automatic and manual
modes
Electronic transmission disconnect
On-board diagnostics with fault code
storage and retrieval
Single, vertically mounted, spin-on oil filter
Oil cooler
HYDRAULICS
Pilot-operated control
2-Spool valve
Pressure compensated, load sensing
hydraulics
Wide-angle steering system
Vertically mounted, spin-on oil filter
Hydraulic diagnostic quick couplers
O-ring face seal hydraulic fittings
Full-flow oil cooler
Steering system priority
LOADER SYSTEM
Automatic return-to-dig, automatic height
control, and automatic return-to-travel
Position indicator on bucket
Single lever / two spool loader control
Z-bar loader linkage
Single piece, flame cut, loader arms
Ground level lubrication points
BRAKES
4-Wheel, outboard mounted, wet disc
hydraulic brakes
OPTIONAL EQUIPMENT
Parking brake; switch actuated, spring
applied hydraulic release
Separate front and rear brake systems
ELECTRICAL SYSTEM
24-volt system
Two Heavy Duty 12V 700 cold cranking
amp (CCA) batteries
Halogen lights:
2 front and 2 rear work-lights
2 front driving (hi/low beam)
Stop/tail lights and backup lights
Front and rear turn signals and flashers
Alternator: 70 amp
Electrical disconnect switch
Horn
Backup alarm
OPERATOR STATION
ROPS cab with heater
Inside rearview mirror
Cloth mechanical suspension seat,
w/ 51 mm (2 in) seatbelt
Storage tray, cup holder
Tilt steering wheel w/integral steering knob
Fully adjustable wrist rest
Cigar/cigarette lighter-24 volt
Wiring & speaker covers, for radio
installation
OPERATOR STATION
Air conditioning for ROPS cab
Mechanical suspension seat,
Cloth covered with 3″ retractable belt
Air suspension seat,
Cloth covered with 2″ retractable belt
Cloth covered with 3″ retractable belt
AM/FM cassette stereo radio, 12 volt
Power converter 24V-12V with outlet
Fire extinguisher
Rotating beacon light
ENGINE
Cold weather starting aid, grid heater
Cold weather starting aid, block heater
Spark arresting muffler
Reversing fan (purge feature)
HYDRAULICS
Valve, 2 spool 2 lever control
Valve, 3 spool 3 lever control
Valve, 3 spool joystick + 1 lever control
Hydraulic pin-puller circuit for use with
coupler
Load Travel Stabilizer (LTS)
Secondary steering
INSTRUMENTS
Individual gauges for:
1. Engine coolant temp.
2. Fuel level
3. Hour meter
4. Speedometer
5. Trans. Oil temp.
Indicator Lights for:
1. Air filter restriction
2. Battery charge
3. Brake oil pressure
4. Emergency Steering (if equipped)
5. Engine coolant temp.
6. Engine oil pressure
7. Fuel level
8. General alarm
9. High beam
10. Parking break
11. Trans. Oil temp.
12. Trans. speed
13. Turn signals
OTHER EQUIPMENT
Articulation and loader lift arm locking bars
Drawbar hitch
Front and rear fenders, left side steps
Remote drain points
Front and rear lift and tie down points
Design, materials and/or specifications are subject to
change without notice and without liability therefor.
Specifications are applicable to units sold in Canada, the
United States, its territories and possessions, and may
vary outside these areas.
Visit our website at www.newhollandconstruction.com
© 2004 CNH America LLC
Safety begins with a thorough understanding of the
equipment. Always make sure you and your operators read the Operator’s Manual before using
the equipment. Pay close attention to all safety
and operating decals and never operate
machinery without all shields, protective
devices and structures in place.
Stock #NHC1230405 • 020405 • API • PRINTED IN U.S.A.
NEW HOLLAND CONSTRUCTION IS A BRAND OF CNH.
A GLOBAL LEADER FOR CONSTRUCTION EQUIPMENT, AGRICULTURE EQUIPMENT AND FINANCIAL SERVICES.
AXLES & TIRES
17.5x25, 12 PR L3 bias ply, rock tread,
1-pc rim
17.5R25, GP2B radial, traction tread,
3-pc rim
17.5R25, XTLA radial, traction tread,
1-pc rim
17.5R25, XTLA radial, traction tread,
3-pc rim
17.5R25, XHA radial, rock tread, 1-pc rim
17.5R25, XHA radial, rock tread, 3-pc rim
Spare tires and wheels
BUCKETS AND ATTACHMENTS
Pin-on buckets—see chart on page three
JRB hydraulic quick coupler with
pin-puller circuit
JRB 2.25 yd3 general purpose bucket
Other JRB attachments available–consult
your New Holland Construction dealer
for details
OTHER EQUIPMENT
Standard fenders with RH and LH steps
Rear frame articulation joint side covers
Axle stops for use with 17.5 tires with chains
Tool box
Transmission side covers
Special paint, other than standard NHC
yellow