OFFICE OF THE EXECUTIVE ENGINEER
JAWAHARLAL NEHRU KRISHI VISHWA VIDYALAYA, JABALPUR
Schedule of item :- Construction of P.G. Boys Hostel Ground Floor at College of Agriculture, Rewa.
S.No
Particulars
1.
Surface dressing of the ground including removing
vegetation and in-equalities not exceeding 15 cm
deep and disposal of rubbish, lead upto 50 m and lift
upto 1.5 m.
 All kinds of soil.
Boring, providing and installing bored cast-in-situ
reinforced cement concrete single under reamed pile
of specified diameter and length below the pile cap
M20 in cement concrete, to carry a safe working load
not less than specified, excluding the cost of steel
reinforcement but including the cost of boring. The
length of the pile to be embedded in the pile cap etc.
all complete, including removal of excavated earth
with all lifts and leads (Length of pile for payment
shall be measured up to bottom of pile cap).
Excluding cost of Steel. And rates are inclusive of
cost of concreate.
 200 mm diameter.
 250 mm diameter.
 300 mm diameter.
Extra for providing additional blub for item no.20.9
 200 mm diameter.
 250 mm diameter.
 300 mm diameter.
Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in over areas
foundation trenches or drains (not exceeding 1.5 m in
width or 10 sqm on plan) including dressing of sides
and ramming of bottoms, lift upto 1.5 m, including
getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m.
All kinds of soil
 Pipes, cables etc, not exceeding 80 mm dia.
Supplying and filling in plinth with crusher stone
dust/ coarse sand under floors including, watering,
ramming consolidating in layers not exceeding 20cm
in depth in layers not exceeding 20cm in depth and
dressing complete.
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
 M - 10 with 40mm nominal size graded stone
aggregate.
Reinforced cement concrete work in beams, suspended
floors, roofs having slope of any degree landings,
balconies, shelves, chajjas, lintels, bands, plain window
sills, staircases and spiral stair cases up to floor two
level excluding the cost of centering, shuttering,
finishing and Reinforcement in concrete grade.
 M 20 Nomial mix (with 20mm nominal size
graded stone aggregate)
2.
3.
4.
5.
6.
7.
My Document/ Tender File-2
Qty.
Unit
Rate
Amount in word
Rs.
840.00
100 M2
553.00
Five hundred fifty three
only
122.40
331.20
208.80
Mt.
Mt.
Mt.
280.00
340.00
506.00
Two hundred eighty only
Three hundred forty only
Five hundred six only
68.00
184.00
116.00
Each
Each
Each
99.00
229.00
448.00
26.496
Cum
107.00
551.726
Cum
530.0
82.158
Cum.
2833.00
255.129
Cum
3863.00
Ninety Nine only
Two hundred Twenty nine only
Four hundred forty eight
only
One hundred seven only.
Five hundred thirty only
Two
thousand
eight
hundred thirty three only
Three thousand eight
hundred sixty three only
8.
9.
10.
11.
12.
13.
Reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position
and binding including cost of binding wire up to floor
two level including all wastage etc. complete.
 Thermo- Mechanically treated bars (TMT)
Centering and shuttering including strutting,
propping etc. and removal of form for :
Suspended floors, roofs, landings, balconies and
platform. Shelves (Cast in situ) Lintels, beams,
 Foundations, footings, bases of columns, etc.
for mass concrete up to plinth level.
 Wall s (any thickness) including attached
pilasters buttresses, plinth beams and string
courses etc. up to plinth level.
 Suspended floors, roofs, landings, balconies
and platform. Shelves (Cast in situ) Lintels,
beams, beams, access girders, bressumers
and cantilevers, Columns, Pillars, Posts and
Struts Walls in super structure.
Brick work with well burnt chimney bricks in bull
spat entrench kiln, crushing strength not less than
25kg /sqcm and water absorption not m ore than 20%
in foundation and plinth
 Cement Mortar 1:6 (1 Cement : 6 sand)
Half brick masonry with M.S. bricks of class
designation 25 in superstructure above plinth level up
to floor II level.
 Cement mortar 1:4 (1 cement :4 sand)
Providing and fixing pressed steel door frames
confirming to IS: 4351manufactured from
commercial mild steel sheet of 1.25 mm thickness
including hinges jamb, lock jamb, bead and if
required angle threshold of mild steel angle of section
50x25mm, or base ties of 1.25mm pressed mild steel
welded or rigidly fixed together by mechanical
means, adjustable lugs with split end tail to each
jamb including steel butt hinges 2.5mm thick with
mortar guards, lock strike- plate and shock absorbers
as specified and applying a coat of approved steel
primer after pre-treatment of the surface as directed
by Engineer-in-charge:
 Double rebate ( size, 115 mm x 50 mm)
Providing and fixing panelled or panelled and glazed
shutters for doors, windows and clerestory windows
including ISI marked black enamelled M.S butt
hinges with necessary screws excluding, panelling
which will be paid for separately.
Kiln seasoned and chemically treated Hollock wood.
 35 mm thick shutters
My Document/ Tender File-2
Kg.
42.00
139.86
Sqm.
127.00
One hundred
seven only
447.03
Sqm.
193.00
One hundred ninety three
only
1057.37
Sqm.
199.00
One hundred ninety nine
only
97.094
Cum
2190.00
Two
thousand
One
hundred ninety only
110.92
Sqm.
302.80
Three hundred two & pisa
eighty only
127.20
Mtr.
348.00
Three hundred forty eight
only
6.98
Sqm.
1126.00
One
thousand
One
hundred twenty two only
28064.419
Forty two only
twenty
14.
15.
16.
17.
18.
19.
Providing and laying Ceramic glazed floor tiles of
any size (910mm thickness) of 1st quality
conforming to IS : 15622 of approved make in
colours such as White, Ivory, Grey, Fume Red
Brown, laid on 20 mm thick Cement Mortar 1:4 (1
Cement : 4 sand) including pointing the joints with
white cement and matching pigment etc., complete.
Providing and fixing Ist quality ceramic glazed wall
tiles conforming to IS : 15622 (6-7mm thickness) of
approved make in all colours, shades except
burgundy, bottle green, black of any size as approved
by Engineer-in-Charge in skirting, risers of steps and
dados over 12 mm thick bed of cement Mortar 1:3 (1
cement : 3 sand) and jointing with grey cement slurry
@ 3.3kg per sqm including pointing in white cement
mixed with pigment of matching shade complete.
Granite stone flooring with 18mm thick granite stone
(sample of granite shall be approved by engineer-incharge) over 20mm (average) thick base of cement
mortar 1:4 (1 cement : 4 sand) laid and jointed with
white cemtent slurry mixed with pigment of required
shade to match the shade of stone complete. (area of
slab over 0.50 sqm) (item to be executed only in
public buildings.)
 All shades other than black
Providing and fixing ISI marked flush door shutters
conforming to IS: 2202 (Part I) decorative type, core of
block board construction with frame of 1st class hard
wood and well matched teak3 ply veneering with vertical
grains or cross bands and face veneers on both faces of
shutters.
 35 mm thick including ISI marked Stainless
Steel butt hinges with necessary screws.
Steel work welded in built up sections/ framed work
including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer using
structural steel etc. as required. hoisting, fixing in
position and applying a priming coat of approved steel
 In gratings, frames, guard bar, ladder,
railings, brackets, gates and similar works.
Providing and laying 60mm thick factory made
cement concrete interlocking paver block of M-30
grade reflective type rubber modulded glossy colour
paving block made by block making machine with
strong vibratory compaction and of approved size and
shape laid in required colour and pattern over and
including 60mm thick compacted bed of stone dust
filling the joints with sand etc. all complete as per the
direction of Engineer in charge including locking
edges wherever required wihing cement concrete
M15 grade or cement mortor 1:3 with pigment of
required shade to match the colour /shade of block
including cost of labour, material , etc. all complete.
My Document/ Tender File-2
53.97
Sqm.
737.00
Seven hundred
seven only.
thirty
193.28
Sqm.
547.00
Five hundred forty seven
only.
38.50
Sqm.
2367.00
Two
thousand
three
hundred sixty seven only.
33.04
Sqm.
1593.00
One
thousand
five
hundred ninety nine only
769.50
Kg.
55.50
28.13
Sqm.
473.00
Fifty five point fifty only
Four hundred
three only
seventy
20.
21.
22.
23.
24.
Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other sections
of approved make conforming to IS: 733 and IS : 1285,
fixed with rawl plugs and screws or with fixing clips, or
with expansion hold fasteners including necessary filling
up of gaps at junctions, at top, bottom and sides with
required PVC/neoprene felt etc. Aluminium sections shall
be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing/ paneling, C.P. brass
/ stainless steel screws, all complete as per architectural
drawings and the directions of Engineer-incharge.
(Glazing and paneling to be paid for separately) :
For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making
provision for fixing of fittings wherever required
including the cost of PVC / neoprene gasket required
(Fittings shall be paid for separately).
 Anodised aluminium (anodised transparent or
dyed torequired shade according to IS: 1868,
Minimumanodic coating of grade AC 15)
Kota /cuddapah stone slabs 25 mm thick in risers of
steps, skirting, dado and pillars laid on 12 mm
(average) thick cement mortar 1:3 (1 cement 3 sand)
and jointed with grey cement slurry mixed with
pigment to match the shade of the slabs, including
rubbing and polishing complete
Kota / cuddapah stone slab flooring over 20 mm
(average) thick base laid over and jointed with grey
cement slurry mixed with pigment to match the shade
of the slab including rubbing and polishing complete
with base of cement mortar 1 : 4 (1 cement : 4 sand) :
11.23.1
 25 mm thick.
Providing and fixing factory made P.V.C. door frame
of size 50x47mm with a wall thickness of 5mm,
made out of extruded 5mm rigid PVC foam sheet
mitred at corners and joined with 2 Nos. of 150mm
long brackets of 15x15mm M.S. square tube, the
vertical door profiles to be reinforced with 19x19mm
M.S. square tube of 19 gauge, EPDM rubber gasket
weather seal to be provided through out the frame.
The door frame to be fixed to the wall using M.S.
screws of 65/100mm size complete as per
manufacturers specification and direction of
Engineer-in-Charge.
Providing and fixing to existing door frames.
 9.120.1 30mm thick factory made panel PVC
door shutter consisting of frame made out of
M.S. tubes of 19 gauge thickness and size of
19mm x 19mm for styles and 15x15mm for top
& bottom rails. M.S. frame shall have a coat of
steel primers of approved make and manufacture
. M.S. frame covered with 5mm thick heat
moulded PVC 'C' channel of size 30mm
thickness, 70mm width out of which 50mm shall
be flat and 20mm shall be tapered in 45degree
My Document/ Tender File-2
278.68
Kg.
236.00
Two hundred thirty six
only
75.10
Sqm.
701.00
Seven hundred one only
368.83
Sqm.
670.00
Six hundred seventy only
64.35
Mtr.
382.00
20.47
Sqm.
2188.00
Three hundred eighty two
only
Two
thousand
one
hundred eighty eight only
25.
26.
27.
28.
29.
30.
31
32.
angle on either side forming styles; and 5mm
thick, 95mm wide PVC sheet out of which
75mm shall be flat and 20mm shall be tapered in
45 degree on the inner side to form top and
bottom rail and 115mm wide PVC sheet out of
which 75mm shall be flat and 20mm shall be
tapered on both sides to form lock rail.
Top,bottom and lock rails shall be provided
either side of the panel. 10mm (5mm x 2 ) thick,
20mm wide cross PVC sheet be provided as gap
insert for top rail & bottom rail. paneling of
5mm thick both side PVC sheet to be fitted in
the M.S.frame welded/ sealed to the styles &
rails with 7mm (5mm+2mm) thick x 15mm
wide PVC sheet beading on inner side, and
joined together with solvent cement adhesive.
An additional 5mm thick PVC strip of 20mm
width is to be stuck on the interior side of the 'C'
Channel using PVC solvent adhesive etc.
complete as per direction of Engineer-incharge. Manufacturer’s specification & drawing
(for W.C. and bathroom door shutter).
Providing and fixing bright finished brass tower bolts
(barrel type) with necessary screws etc. complete :
 200x10 mm
Providing and fixing bright finished brass handles
with screws etc. complete :
 125 mm
Providing and fixing aluminium hanging floor door
stopper ISI marked anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or
dyed to required colour and shade with necessary
screws etc. complete.
 Twin rubber stopper
Providing and fixing ISI marked oxidized M.S. liding
door bolts with nuts and screws etc.
 250x16 mm
6 mm cement plaster of mix :CM 1:3 (1 cement: 3
sand)
12mm thick cement plaster of mix:
 1:4 (1 cement : 4 sand)
15mmthickcement plaster on rough side of or half
brick wall of mix:
 1:4 (1 cement : 4 sand)
Providing and applying Birla/J.K. or equivalent wall
care exterior/interior mix putty for outer surface i/c
sand pappering for making the surface smooth for
applying any or vinyle paint with all cost of
materials, labours, and scaffolding etc. in all position
complete.(this Item is to be executed only in new
public buildings).
My Document/ Tender File-2
44
Each
219.00
Two hundred nineteen nine
only
62
Each
106.00
One hundred six only
18
Each
49.00
Forty nine only
18
501.30
Each
Sqm.
86.00
69.00
Eighty six only
Sixty nine only
564.43
Sqm.
90.00
Ninety only
672.86
Sqm.
106.00
1738.59
Sqm
93.00
One hundred six only
Ninety three only
33.
34.
35.
36.
Wall painting with plastic emulsion paint of approved
brand and manufacture to give an even shade:
 Two or more coats on new work
Finishing walls with Acrylic Smooth exterior +paint
of required shade:
 New work (Two or more coat applied @ 1.67 ltr/10
sqm over and including base coat of water proofing
cement paint applied @ 2.20 kg/ 10 sqm).
Painting with synthetic enamel paint of approved
brand and manufacture to give an even shade :
 Two or more coats on new work
Providing and fixing glazing in steel doors windows,
ventilator, shutters & partitions etc. per architectural
drawing & asper direction of engineer-incharge.With steel beading metal sash puttey.
 With float glass 4mm thick
1410.36
Sqm
46.00 Forty six only
328.23
Sqm.
59.00
Fifty nine only
155.74
Sqm.
37.00
Thirty seven only
55.37
Sqm.
646.00
Six hundred forty six only
Note :- Tender rates shall be applicable (% rate) in base item also. Any other items of S.O.R. can also be
incorporated in the schedule during execution of work.
Assistant Engineer (Civil)
J.N.K.V.V., Jabalpur
My Document/ Tender File-2
Executive Engineer
J.N.K.V.V., Jabalpur