3550
System image file is "flash:c3550-i5q3l2-mz.121-20.EA1a/c3550-i5q3l2-mz.12120.EA1a.bin"
cisco WS-C3550-24 (PowerPC) processor (revision N0) with 65526K/8192K bytes of
m
emory.
Processor board ID CAT0835N0ZR
Last reset from warm-reset
Bridging software.
Running Layer2/3 Switching Image
The password-recovery mechanism is enabled.
384K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:00:AF:D0:80
Motherboard assembly number: 73-5700-11
Power supply part number: 34-0966-04
Motherboard serial number: CAT083500TM
Power supply serial number: DTH08314MGG
Model revision number: N0
Motherboard revision number: A0
Model number: WS-C3550-24-EMI
System serial number: CAT0835N0ZR
Configuration register is 0x10F
CORE-CreweLib-A(config)#policy-map BAZ
CORE-CreweLib-A(config-pmap)#class class-default
CORE-CreweLib-(config-pmap-c)#?
QoS policy-map class configuration commands:
bandwidth Bandwidth
exit
Exit from QoS class action configuration mode
no
Negate or set default values of a command
trust
Set trust value for the class
<cr>
police Police
set
Set QoS values
The router will not accept this command
CORE-CreweLib-(config-pmap-c)#police 1000000 exceed-action drop
CORE-CreweLib-(config-pmap-c)#police ?
<8000-1000000000> Bits per second
aggregate
Choose aggregate policer for current class
Under int gig0/1
CORE-CreweLib-A(config-if)#service-policy output BAZ
I/f GigabitEthernet0/1 class class-default requested bandwidth 1000000 (kbps) A
vailable only 750000 (kbps)
When I try to put this command on the input I get the following error
CORE-CreweLib-A(config-if)#service-policy input BAZ
CORE-CreweLib-A(config-if)#
1d01h: CBWFQ : Can be enabled as an output feature only
1d01h: CBWFQ : Can be enabled as an output feature only
1d01h: CBWFQ : Can be enabled as an output feature only
3560
ROM: Bootstrap program is C3560 boot loader
BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC,
RELEASE SOFTWAR
E (fc4)
Crewe-YOT uptime is 1 day, 2 hours, 5 minutes
System returned to ROM by power-on
System image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.1
22-35.SE5.bin"
cisco WS-C3560-24PS (PowerPC405) processor (revision R0) with 122880K/8184K
byte
s of memory.
Processor board ID FDO1235Y2WS
Last reset from power-on
3 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
Base ethernet MAC Address
: 00:23:05:D7:7F:00
Motherboard assembly number : 73-9673-10
Power supply part number
: 341-0029-05
Motherboard serial number
: FDO1235012K
Power supply serial number
: DTN122644B2
Model revision number
: R0
Motherboard revision number : A0
Model number
: WS-C3560-24PS-E
System serial number
: FDO1235Y2WS
Top Assembly Part Number
: 800-26380-05
Top Assembly Revision Number : A0
Version ID
: V07
CLEI Code Number
: COMUZ10ARA
Hardware Board Revision Number : 0x01
Switch Ports Model
SW Version
SW Image
------ ----- ----------------------* 1 26 WS-C3560-24PS
12.2(35)SE5
C3560-IPSERVICES-M
Configuration register is 0xF
Crewe-YOT(config)#policy-map Bandwidth
Crewe-YOT(config-pmap)#clas
Crewe-YOT(config-pmap)#class clas
Crewe-YOT(config-pmap)#class class-default
Crewe-YOT(config-pmap-c)#?
QoS policy-map class configuration commands:
exit
Exit from QoS class action configuration mode
no
Negate or set default values of a command
police
Police
service-policy Configure QoS Service Policy
set
Set QoS values
trust
Set trust value for the class
<cr>
Crewe-YOT(config-pmap-c)#police ?
<8000-10000000000> Bits per second (postfix k, m, g optional; decimal point
allowed)
aggregate
Choose aggregate policer for current class