7100SZ Series SafeZone™
Installation and Instruction Manual
Patent Pending
80-9371-0081-020 (10-10)
Pull Side Applications with Slide Track
(7110SZ, 7150SZ)
(see page 5 for template)
2
3
1
Push Side Applications with Double Lever Arms
(7120SZ, 7130SZ)
(see page 3 for template)
4
Item No. Description
1
Track
2
3
4
Cover
Arm (Pull Side)
Double Lever Arm (Push Side)
Requirements:
!
!
!
!
!
!
!
!
!
Units are handed. Hand of unit and hand of door must be the same.
Door must be hung on ball bearing butt hinges or ¾” (19) offset pivots.
Door thickness must be 1¾” (44) minimum 2¼” (64) maximum.
Door must swing freely through the entire opening and closing cycle before beginning the installation procedure.
Frame face must be a minimum of 2” (51).
Ceiling clearance must be a minimum of 4” (102).
Power input to unit must be of the same voltage as that stated on the unit.
Unit to be mounted on interior of building in dry environment, maximum humidity of 95%.
See NFPA70 for wiring requirements and NFPA72 for alarm system requirements.
Component Layout
Backplate
Closer/Holder Unit
Assembly
Preparation for Fasteners
Sensor
Hook-up Board
Fasteners
Test Switch
Access Tube
Door or Frame
1/4” - 20 machine
screw
Hollow
Metal
Standard
Sleeve nuts and bolts
Backplate
Mtg Screw (5)
Metal
Optional Through-bolts and
grommet-nuts
Drill-Sizes
Drill: #7 (0.201” dia.)
Tap: 1/4” - 20
9/32” (7 mm) through;
3/8” (9.5 mm) door face
opposite to closer
Aluminum 3/8” (9.5 mm) through
or Wood
9/32” (7 mm);
3/8” (9.5 mm) dia. x
All
3/8” (9.5 mm) deep on
door opposite to closer
Cover Mtg
Screw (3)
Cover
Included with 7110SZ and 7150SZ
Included with 7120SZ and 7130SZ
7110 Main Arm (7210-1A)
7150 Main Arm, Handed
(7250-1L, 7250-1R)
7130 Arm
Assembly
(7701-1B)
Slide Track
(7200-1T)
Arm Screw
(7701-MAS)
Screw &
Washer
7120 Arm
Assembly
(7701-1A)
Slide Assembly
(7700SLD)
Track Mtg
Screw (3)
NOTE: Optional remote
for Advanced Settings
(sensitivity, door control
mode) if required.
(7100REM)
Certifications
UL228
UL10B
Page 2
80-9371-0081-020 (10-10)
Ceiling Line
7120SZ, 7130SZ
Use of an auxiliary door stop, by
others, is suggested, but is required
for doors opening beyond 110°.
3-1/2
Min
(89)
Double Lever Arm
(Push Side)
2
Min
(51)
Hinge
Edge
RH - Right Hand Door
LHR - Left Hand Reverse
1
Left Hand Door - LH
Right Hand Reverse - RHR
Drill #7; Tap 1/4-20
19-3/16
(487)
4
(102)
11-3/8
(289)
8-11/16
(221)
5/16
11/16
(8)
(17)
4-1/8
(105)
A
For Concealed
WiringOnly
7/8
(22)
2
DIA THRU
For Concealed Wired Only
(If surface wired, go to
Step 3.)
7-1/2
(191)
1-3/4
(44)
1-5/8
(41)
Left hand door shown, right hand opposite.
C
All dimensions shown in inches (mm).
Hinge or Pivot
DOOR OPENING
ANGLE
To 100°
100° to 180°
Dimension “A”
Inches
(mm)
5-7/8
3-1/8
150
80
3
6
5
4
L
R
Y
S
Arm
Mark
Main
Arm
Z
Arm
Pinion Screw
Flat
(7/16” Drive)
Page 3
80-9371-0081-020 (10-10)
8
7
90°
Closing Force
11/16”
Drive
+
9
Latch
Product shipped with closing
force set at the middle of the
power range.
11/16" Drive
Backcheck
Sweep
1/8” wrench
provided
Backcheck
Strength
!
Backcheck
Positioning
(75° - 95°)
10
Caution: Do not completely
close backcheck valve.
MAKE ELECTRICAL CONNECTIONS:
• Power input to unit must be of the same voltage as that listed on the label.
• All wiring connections use standard wiring practice conforming to local wiring codes.
• Maximum wire size is 18AWG.
• Make input power connections to the hook-up board terminal strip using illustrations.
24V AC/DC INPUT CIRCUIT BOARD
120V AC INPUT CIRCUIT BOARD
Test Switch
Fuse
Fuse
Test Switch
PTO125V
(125V / 1/2A)
PTO125V
(125V / 1/2A)
Solenoid
Connection
24V AC/DC
Power Input
11
!
Caution:
Determine proper
control board; 24V or 120V.
Safe Zone Sensor
Connection
120V AC
Power Input
Solenoid
Connection
Safe Zone Sensor
Connection
12
Adjust settings
Page 4
80-9371-0081-020 (10-10)
Ceiling Line
7110SZ, 7150SZ
Use of an auxiliary door stop, by
others, is suggested, but is required
for doors opening beyond 110°.
4
Min
(102)
Track Mount (Pull Side)
2
Min
(51)
RH - Right Hand Door
LHR - Left Hand Reverse
1
Drill #7; Tap 1/4-20
4
(102)
3-1/4
(83)
Left Hand Door - LH
Right Hand Reverse - RHR
19-3/16
(487)
11-3/8
(289)
4-1/8
(105)
8-11/16
(221)
1-1/16
1-3/8
(27)
(35)
For Concealed
Wiring Only
7/8
(22)
DIA THRU
For Concealed Wired Only
(If surface wired, go to
Step 3.)
Track Mount Unit
4
(102)
1-3/16
(30)
11
(279)
! Right hand door shown,
left hand opposite.
! All dimensions shown in
inches (mm).
22
(559)
C
2
Hinge or Pivot
3
4
Fully close Latch and Sweep
Valves with 1/8" wrench
provided.
5
6
Arm Indexing
RIGHT
HAND
Use main arm to rotate pinion
until flat is visible.
RE-INSTALL
HERE
LEFT
HAND
PINION
FLAT
Page 5
80-9371-0081-020 (10-10)
7
9
8
Arm
Stud
Slide
Assembly
1
Arm Washer
Arm Screw
Open Latch & Sweep Valves
Main Arm with 1/8” wrench provided.
2
10
11
Closing Force
!
Caution:
Do not completely
close backcheck valve
1/8” wrench
provided
Latch
+
12
11/16”
Drive
Sweep
Backcheck
Strength
Backcheck
Positioning
(75° - 95°)
Product shipped
with closing force
set at the middle of
the power range.
MAKE ELECTRICAL CONNECTIONS:
• Power input to unit must be of the same voltage as that listed on the label.
• All wiring connections use standard wiring practice conforming to local wiring codes.
• Maximum wire size is 18AWG.
• Make input power connections to the hook-up board terminal strip using illustrations.
24V AC/DC INPUT CIRCUIT BOARD
Fuse
Fuse
Caution:
Determine proper
control board; 24V or 120V.
Test Switch
PTO125V
(125V / 1/2A)
PTO125V
(125V / 1/2A)
Solenoid
Connection
13
!
120V AC INPUT CIRCUIT BOARD
Test Switch
24V AC/DC
Power Input
Backcheck
Safe Zone Sensor
Connection
120V AC
Power Input
Solenoid
Connection
Safe Zone Sensor
Connection
14
Adjust settings
Page 6
80-9371-0081-020 (10-10)
SafeZone™ Set-Up
Sensor Technical Specifications
DESCRIPTION
SPECIFICATION
Frequency:
Supply voltage:
24.125 GHz
12 to 24 V AC: ± 10%:
12 to 24 V DC: -10% / +30%:
Normal: 7’; Maximum: 10’-0”
0° to 90° vertical
-15° to +15° lateral
Mounting height:
Tilt angle:
Detection area:
Wide
Narrow
Minimum detection speed:
Power consumption:
Standard output relay:
Max contact voltage
Max contact current
Max switching power
Hold time:
Temperature range:
Dimensions:
Weight:
Material:
13ft (W) x 6.5ft (D)
6.5ft (W) x 8.2ft (D) (supplied as optional)
2 in/sec. (measured in axis)
<2W
60 VDC / 125 VAC
1 A (resistive)
30W (DC) / 60VA (AC)
0.5 sec. to 9 sec. (adjustable)
-4°F to 131°F
4.75in (W) x 3.15in (H) x 2.0in (D)
0.5lbs
ABS
Safety Precautions
•
•
•
•
•
•
Shut off all power going to the header before attempting any wiring procedures.
Maintain a clean & safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by
the door.
Always check placement of all wiring and components before powering up to insure that moving door parts will not
catch any wires and cause damage to equipment.
Ensure compliance with all applicable safety standards upon completion of installation.
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS
Circuit board components are vulnerable to damage by electrostatic discharge
(ESD). ESD can cause immediate or subtle damage to sensitive electronic parts.
An electrostatic charge can build up on the human body and then discharge when
you touch a board. A discharge can be produced when walking across a carpet
and touching a board, for example. Before handling any board, make sure you
dissipate your body’s charge.
CAUTION: In the event a unit needs to be opened, observe the following precautions.
Ground yourself by touching a conductive surface of the door or other element connected to common earth
ground to discharge the static electricity present in your body.
Avoid walking around while replacing items inside the case, especially if you are on carpet or during
conditions of low temperature and low humidity.
Handle the board by the edges only to avoid touching electronic components.
Store a loose board in an anti-static bag.
Page 7
80-9371-0081-020 (10-10)
Mechanical Adjustments
THE POSITION OF THE SENSING FIELD IS DETERMINED BY THE VERTICAL AND LATERAL ANGLE OF THE ANTENNA
B
A
C
-30º
0º
45º
30º
Sensing field as close to the door as possible:
-antenna set at the position of 0°
Sensing field close to the door:
-antenna set at the position of 30°
Sensing field far from the door:
-antenna set at the position of 45°
Set Up
+ Press to increase
hold open setting
(see table below).
Hold open time refers to the time the
door will remain open AFTER
movement is no longer detected.
Hold open time can be adjusted
manually by means of the push
buttons + (more) and - (less).
Setting
0
1
2
3
4
5 (Default)
6
7
8
9
Time (Seconds)
0.5
5
6
7
8
10
14
16
18
20
+30
- Press to decrease
hold open setting.
Pressing the two push buttons,
located on the circuit board,
simultaneously for three
seconds, will restore all default
settings.
Recommended Settings:
Setting 1-3
Setting 4-6
Setting 7-9
Troubleshooting
SYMPTOMS
PROBABLE CAUSE
Red LED does not light up.
The sensor power is off.
Check the wiring and power supply.
Cable is not connected.
Connect cable.
CORRECTIVE ACTION
ASSA ABLOY
Norton ® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Safe Zone™ is a trademark of Yale Security
Inc., an ASSA ABLOY Group company. Copyright © 2010 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Page 8
3000 Highway 74 East Monroe, NC 28112
Tel: (877)-974-2255 Fax: (800)-338-0965
www.nor tondoorcontrols.com
80-9371-0081-020 (10-10)