INSTRUCTIONS FOR PREPARATION OF PAPERS

advertisement
INSTRUCTIONS FOR PREPARATION OF PAPERS
FOR XXII SYMPOSIUM EPNC 2012
Andrzej Nowak, Kay H. Yeadon*, Ryszard Chmielnicki
Poznań University of Technology, Institute of Industrial Electrical Engineering
Piotrowo 3a, 61-138 Poznań, Poland, e-mail: epnc@put.poznan.pl
*Katholieke Universiteit Leuven, Electrical Engineering Department, Div. ESAT/ELEN
Kasteelpark Arenberg 10, B 3001 Leuven-Heverlee, Belgium, e-mail: khyeadon@esat.kuleuven.ac.be
Abstract - The paper should be prepared as a camera ready text
on A4 paper (210 x 297 mm). Only papers written in English will
be published in the proceedings. The paper will be printed directly
from the supplied text, therefore neat and accurate preparation
as well as linguistic correctness of the English text are very
important. Paper must contain an abstract not exceeding 100
words. The papers should be submitted in DOC and PDF format
directly to the Symposium Secretariat.
Tables should be numbered. Table captions should be
centred.
TABLE I
TYPE SIZES AND APPEARANCE
Size
in
points
Times New Roman
Appearance
I. GENERAL INFORMATION
The paper should be prepared in double-column format not
exceeding 2 pages in overall length including figures, tables
and references. Microsoft Word or any other word processor
should be used. Use an English spelling corrector and if your
native language is not English, get a language specialist
to proof-ready your paper. Do not number the pages.
II. TECHNICAL INFORMATION
14
10
9
10
10
8
10
9
8
8
TITLE
Authors’ Names, Main Text
Affiliations
Equations
SECTION TITLES
TABLE CAPTIONS
Subheadings
Abstract
Tables, Figure captions
Footnotes, References
Type typefaces and sizes: Times New Roman or a similar
typeface is advisable. Follow the type sizes specified in Table I.
Format: Set the top margin to 35 mm for the first page and
20 mm for second page, the bottom margin to 20 mm. Set
the left and right margin to 15 mm. The width of the
columns should be set to 88 mm and the space between them
to 4 mm. Use 3.5 mm for paragraph indentation. Leftand right-justify your text. On the second page, try to adjust
the lengths of the two columns so that they are the same.
Spacing: single. Titles, authors’ names, authors’ affiliation,
section titles, figures, captions, tables and equations should
be centred and separated by empty lines.
B. Formulas
A. Figures and tables
C. References
bold, CAPITAL LETTERS
CAPITAL LETTERS
SMALL CAPS
italic
bold
Formulas should be centred and numbered in round brackets.
The brackets should be placed to the right of the formula.
1
curl curl A  J


(1)
Physical quantities written with the Latin alphabet must be
typed in italics. Put an empty line between the text and the
formula.
When citing references in the text, put the corresponding
reference number in square brackets [1].
REFERENCES
AC supply
Fig.1. System with nonlinear elements
Figures should be inserted in the text. Captions should
be placed under figures as shown in Figure 1.
[1] L. Bojtor, I. Schmitd, “Simulation of controlled converter-fed
synchronous motor”, Proc. of 4-th European Conference on Power
Electronics and Applications, Firenze, vol.4, pp. 609-614, 1991.
[2] A. Bossavit, “How weak is the ‘weak solution’ in finite element
methods”, IEEE Trans.Magn., vol. 33, No. 5, pp. 2429-2432, 1998.
[3] M.P. Kaźmierkowski, H. Tunia, Automatic control of converter-fed
drives. Amsterdam, Elsevier, 1994.
[4] C. Numudri, P. C. Sen, “Digital simulation of an inverter-fed selfcontrolled synchronous motor”, IEEE Trans. Ind. Electr., IE-34, No. 2,
pp. 205-215, 1987.
Download