MATERIAL SAFETY DATA SHEET
PRODUCT NAME ThermoFlex Sport
DISTRIBUTOR
Specialty Materials
2929 West 21st Street
Tulsa, OK 74107
USA
Tel: 918-437-8599
Fax: 918-437-8588
1. Product Description: – Adhesive film for adhesive backed fabrics.
2. Hazardous Ingredients
None
3. Physical Data
Property
Value
Material Form
Boiling Point
Melting Point
Vapor Pressure
Evaporation Rate
Solubility in Water
Odor
Color
Solid
Not applicable
Adhesives melt below 350º F
Not applicable
Not applicable
Insoluble
None
Varies
4. First Aid Measures
Inhalation:
Move to fresh air in case of accidental inhalation of fumes from
overheating or combustion. When symptoms persist or in cases of
doubt, seek medical advice.
Ingestion:
Do not induce vomiting without medical advice. When symptoms
persist or in cases of doubt, seek medical advice.
Eyes:
Rinse immediately with plenty of water for at least 15 minutes. If
eye irritation persists, seek medical attention.
Skin:
Wash off with soap and water. If skin irritation persists, seek
medical attention.
5. Fire Fighting Measures
Flash Point:
Above 300º F
Extinguishing media: Carbon dioxide blanket, water spray, dry powder, foam.
Special procedures: Full-face self-contained breathing apparatus (SCBA) used
in positive pressure mode should be worn to prevent
inhalation airborne contaminates.
Fire hazards:
Carbon Monoxide (CO), Carbon Dioxide (CO2), oxides of
nitrogen, other hazardous materials, and smoke are all
possible.
1
Specialty Materials
Material Safety Data Sheet
ThermoFlex Sport
Page 2 of 3
Date: June 2, 2008
6. Accidental Release Measures
This product form is not conducive to accidental release. It should not be allowed
to enter water courses, drains, or the soil. Refer to 12 for disposal methods.
7. Handling and Storage
Store at room temperature.
8. Exposure Controls/Personal Protection
No personal respiratory protective equipment normally required. Heat only in
areas with appropriate ventilation. Handle in accordance with good industrial
hygiene and safety practices. Wash hands before breaks and at the end of the
workday.
9. Stability and Reactivity
Stability:
Stable
Hazardous Polyermerization: Will not occur
Conditions to avoid:
Keep away from open flames and oxidizing agents.
To avoid thermal decomposition, do not overheat.
Incompatible Materials:
Strong oxidizing agents.
Hazardous Decomposition
Products:
Carbon Monoxide (CO), oxides of nitrogen, other
hazardous materials and smoke. Prolonged heating
at temperatures above about 390º F may result in
thermal decomposition.
10. Toxicological Information:
None of the ingredients in this product exceeding a concentration of 0.1% are on
the OSHA list of carcinogenic hazards.
11. Ecological Information
Not readily biodegradable. Adverse ecological impact is not known or expected
under normal use.
12. Disposable Considerations
The generator of waste material has the responsibility for proper waste
classification, transportation, and disposal in accordance with applicable federal,
state/provincial and local regulations.
13. Transportation Information
U.S. DOT Classification:
ICAO/IATA (air):
IMO/IMDG (maritime):
not regulated for transportation
not regulated for transportation
not regulated for transportation
2
Specialty Materials
Material Safety Data Sheet
ThermoFlex Sport
Page 3 of 3
Date: June 2, 2008
14. Other Information
The information provided in this Safety Data Sheet is correct to the best of our
knowledge, information and belief at the date of its publication. The information given is
designed only as guidance for safe use and is not considered a warranty or quality
specification. The information relates only to the specific material designated and may
not be valid for such material when used in combination with other materials and/or in
any particular process or processing conditions.
3