PHILIPPINE BIDDING DOCUMENTS
(As Harmonized with Development Partners)
Procurement of
GOODS
Supply and Delivery of Materials for
Two (2)-Units 175KVA 220V/460V, 3Phase, 60 Hz,
Non Polychlorinated Biphenyl (PCB)
Transformer with Complete Accessories at Port of
General Santos, Makar Wharf, General Santos City
Government of the Republic of the Philippines
Fourth Edition
December 2010
TABLE OF CONTENTS
SECTION I. INVITATION TO BID ............................................................................3
SECTION II. INSTRUCTIONS TO BIDDERS .............................................................6
SECTION III. BID DATA SHEET ......................................................................... 34
SECTION IV. GENERAL CONDITIONS OF CONTRACT ....................................... 38
SECTION V. SPECIAL CONDITIONS OF CONTRACT ........................................... 55
SECTION VI. SCHEDULE OF REQUIREMENTS.................................................... 61
SECTION VII. TECHNICAL SPECIFICATIONS ..................................................... 62
SECTION VIII. BIDDING FORMS ........................................................................ 64
Section I. Invitation to Bid
3
Port Management Office – General Santos
Makar Wharf, Labangal, General Santos City, Tel. No. (083) 552-4484, 380-3628; Fax No. (083) 552-4446
Email Address: ppa_gensan@yahoo.com
INVITATION TO BID FOR
Supply and Delivery of Materials
for Two (2) Units-175KVA 220V/460V, 3Phase,
60 Hz Non Polychlorinated Biphenyl (PCB) Transformer
with Complete Accessories at Port of General Santos,
Makar Wharf, General Santos City
The Philippine Ports Authority, Port Management Office of General Santos
(PPA, PMO-GS), through the Corporate Budget for 2013 intends to apply the sum of One
Million One Hundred Fifty One Thousand Six Hundred Fifty Pesos (1,151,650.00) being
the Approved Budget for the Contract (ABC) to payments under the contract Supply and
Delivery of Materials for Two (2) Units-175KVA, 220V/460V, 3Phase, 60 Hz, Non
Polychlorinated Biphenyl (PCB) Transformer with Complete Accessories at Port of General
Santos, Makar Wharf, General Santos City.
1.
Bids received in excess of the ABC shall be automatically rejected at bid opening.
The PPA, PMO-GS Bids and Awards Committee for Procurement of Goods
(BAC-PG) now invites bids for Supply and Delivery of Materials for Two (2) Units175KVA, 220V/460V, 3Phase, 60 Hz, Non Polychlorinated Biphenyl (PCB)
Transformer with Complete Accessories at Port of General Santos, Makar Wharf,
General Santos City. Delivery of the goods is required within thirty (30) calendar
days from the signing of the contract. Bidders should be a licensed and duly
authorized dealer of heavy duty electrical equipment, supplies and accessories.
2.
Bidding will be conducted through open competitive bidding procedures using a nondiscretionary “pass/fail” criterion as specified in the Implementing Rules and
Regulations (IRR) of Republic Act (RA) 9184, otherwise known as the “Government
Procurement Reform Act”.
3.
Bidding is restricted to Filipino citizens/sole proprietorships, partnerships, or
organizations with at least sixty percent (60%) interest or outstanding capital stock
belonging to citizens of the Philippines, and to citizens or organizations of a country the
laws or regulations of which grant similar rights or privileges to Filipino citizens,
pursuant to RA 5183 and subject to Commonwealth Act 138.
4.
Interested bidders may obtain further information from Secretariat of the BAC-PG
and inspect the Bidding Documents at the address given below during 8:00 am to 5:00
pm, Monday to Friday.
4
5.
A complete set of Bidding Documents may be purchased by interested Bidders from the
address below and upon payment of a nonrefundable fee for the Bidding Documents in
the amount of Five Thousand Pesos (Php5,000.00) (VAT exclusive).
It may also be downloaded free of charge from the website of the Philippine
Government Electronic Procurement System (PhilGEPS) and the website of the
Procuring Entity, provided that Bidders shall pay the nonrefundable fee for the Bidding
Documents not later than the submission of their bids.
6.
PPA PMO-GS BAC-PG will hold a Pre-Bid Conference on October 16, 2013 @
9:00AM at PPA Phil-Am Hall, Makar Wharf, General Santos City, which shall be
open to all interested parties.
7.
Bids must be delivered to the address below on or before October 29, 2013 @ 1:00
P.M.. All Bids must be accompanied by a bid security in any of the acceptable forms
and in the amount stated in ITB Clause 18.
Bid opening shall be on the same day at 1:30 P.M. Bids will be opened in the presence
of the Bidders’ representatives who choose to attend at the address below. Late bids
shall not be accepted.
8.
The PPA PMO-GS BAC-PG reserves the right to accept or reject any bid, to annul
the bidding process, and to reject all bids at any time prior to contract award, without
thereby incurring any liability to the affected bidder or bidders.
9.
For further information, please refer to:
MARIA VIVIEN M. TANCO
Head, BAC- PG Secretariat
Philippine Ports Authority, Port Management Office- General Santos
Makar Wharf, General Santos City
Tel. Nos. (083) 301-2074
Email Add:mv_tanco@yahoo.com
Fax No. (083)552-4446
Website:www.ppa.com.ph
(Sgd) LUZ PATRICIA F. TANCO
Chairperson, BAC-PG
5
Section II. Instructions to Bidders
6
TABLE OF CONTENTS
A. GENERAL .......................................................................................................... 9
1.
Scope of Bid ............................................................................................................... 9
2.
Source of Funds .......................................................................................................... 9
3.
Corrupt, Fraudulent, Collusive, and Coercive Practices ............................................ 9
4.
Conflict of Interest ................................................................................................... 10
5.
Eligible Bidders ........................................................................................................ 12
6.
Bidder’s Responsibilities.......................................................................................... 13
7.
Origin of Goods ........................................................................................................ 15
8.
Subcontracts ............................................................................................................. 15
B. CONTENTS OF BIDDING DOCUMENTS .............................................................. 15
9.
Pre-Bid Conference .................................................................................................. 15
10.
Clarification and Amendment of Bidding Documents ............................................. 16
C. PREPARATION OF BIDS .................................................................................... 16
11.
Language of Bid ....................................................................................................... 16
12.
Documents Comprising the Bid: Eligibility and Technical Components ................ 16
13.
Documents Comprising the Bid: Financial Component .......................................... 18
14.
Alternative Bids........................................................................................................ 19
15.
Bid Prices ................................................................................................................. 19
16.
Bid Currencies .......................................................................................................... 20
17.
Bid Validity .............................................................................................................. 21
18.
Bid Security .............................................................................................................. 21
19.
Format and Signing of Bids ..................................................................................... 23
20.
Sealing and Marking of Bids .................................................................................... 24
D. SUBMISSION AND OPENING OF BIDS ................................................................ 24
21.
Deadline for Submission of Bids ............................................................................. 24
22.
Late Bids .................................................................................................................. 25
23.
Modification and Withdrawal of Bids ...................................................................... 25
24.
Opening and Preliminary Examination of Bids ....................................................... 25
E. EVALUATION AND COMPARISON OF BIDS ....................................................... 27
25.
Process to be Confidential ........................................................................................ 27
26.
Clarification of Bids ................................................................................................. 27
27.
Domestic Preference ................................................................................................ 27
7
28.
Detailed Evaluation and Comparison of Bids .......................................................... 28
29.
Post-Qualification..................................................................................................... 29
30.
Reservation Clause ................................................................................................... 30
F. AWARD OF CONTRACT .................................................................................... 31
31.
Contract Award ........................................................................................................ 31
32.
Signing of the Contract ............................................................................................ 32
33.
Performance Security ............................................................................................... 32
34.
Notice to Proceed ..................................................................................................... 33
8
A. General
1.
2.
Scope of Bid
1.1.
The procuring entity named in the BDS (hereinafter referred to as the
“Procuring Entity”) wishes to receive bids for supply and delivery of the
goods as described in Section VII. Technical Specifications (hereinafter
referred to as the “Goods”).
1.2.
The name, identification, and number of lots specific to this bidding are
provided in the BDS. The contracting strategy and basis of evaluation of lots
is described in ITB Clause 28.
Source of Funds
The Procuring Entity has a budget or has applied for or received funds from the
Funding Source named in the BDS, and in the amount indicated in the BDS. It intends
to apply part of the funds received for the Project, as defined in the BDS, to cover
eligible payments under the contract.
3.
Corrupt, Fraudulent, Collusive, and Coercive Practices
3.1.
Unless otherwise specified in the BDS, the Procuring Entity as well as the
bidders and suppliers shall observe the highest standard of ethics during the
procurement and execution of the contract. In pursuance of this policy, the
Procuring Entity:
(a)
defines, for purposes of this provision, the terms set forth below as
follows:
(i)
“corrupt practice” means behavior on the part of officials in the
public or private sectors by which they improperly and
unlawfully enrich themselves, others, or induce others to do so,
by misusing the position in which they are placed, and includes
the offering, giving, receiving, or soliciting of anything of value
to influence the action of any such official in the procurement
process or in contract execution; entering, on behalf of the
government, into any contract or transaction manifestly and
grossly disadvantageous to the same, whether or not the public
officer profited or will profit thereby, and similar acts as
provided in RA 3019.
(ii)
“fraudulent practice” means a misrepresentation of facts in
order to influence a procurement process or the execution of a
contract to the detriment of the Procuring Entity, and includes
collusive practices among Bidders (prior to or after bid
submission) designed to establish bid prices at artificial, noncompetitive levels and to deprive the Procuring Entity of the
benefits of free and open competition.
9
(b)
4.
(iii)
“collusive practices” means a scheme or arrangement between
two or more Bidders, with or without the knowledge of the
Procuring Entity, designed to establish bid prices at artificial,
non-competitive levels.
(iv)
“coercive practices” means harming or threatening to harm,
directly or indirectly, persons, or their property to influence
their participation in a procurement process, or affect the
execution of a contract;
(v)
“obstructive practice” is
(aa)
deliberately destroying, falsifying, altering or
concealing of evidence material to an administrative
proceedings or investigation or making false statements
to investigators in order to materially impede an
administrative proceedings or investigation of the
Procuring Entity or any foreign government/foreign or
international financing institution into allegations of a
corrupt, fraudulent, coercive or collusive practice;
and/or threatening, harassing or intimidating any party
to prevent it from disclosing its knowledge of matters
relevant to the administrative proceedings or
investigation or from pursuing such proceedings or
investigation; or
(bb)
acts intended to materially impede the exercise of the
inspection and audit rights of the Procuring Entity or
any foreign government/foreign or international
financing institution herein.
will reject a proposal for award if it determines that the Bidder
recommended for award has engaged in any of the practices mentioned
in this Clause for purposes of competing for the contract.
3.2.
Further, the Procuring Entity will seek to impose the maximum civil,
administrative, and/or criminal penalties available under applicable laws on
individuals and organizations deemed to be involved in any of the practices
mentioned in ITB Clause 3.1(a).
3.3.
Furthermore, the Funding Source and the Procuring Entity reserve the right to
inspect and audit records and accounts of a bidder or supplier in the bidding
for and performance of a contract themselves or through independent auditors
as reflected in the GCC Clause 3.
Conflict of Interest
4.1.
All Bidders found to have conflicting interests shall be disqualified to
participate in the procurement at hand, without prejudice to the imposition of
appropriate administrative, civil, and criminal sanctions. A Bidder may be
considered to have conflicting interests with another Bidder in any of the
10
events described in paragraphs (a) through (c) below and a general conflict of
interest in any of the circumstances set out in paragraphs (d) through (f)
below:
4.2.
(a)
A Bidder has controlling shareholders in common with another Bidder;
(b)
A Bidder receives or has received any direct or indirect subsidy from
any other Bidder;
(c)
A Bidder has the same legal representative as that of another Bidder
for purposes of this bid;
(d)
A Bidder has a relationship, directly or through third parties, that puts
them in a position to have access to information about or influence on
the bid of another Bidder or influence the decisions of the Procuring
Entity regarding this bidding process. This will include a firm or an
organization who lends, or temporarily seconds, its personnel to firms
or organizations which are engaged in consulting services for the
preparation related to procurement for or implementation of the project
if the personnel would be involved in any capacity on the same project;
(e)
A Bidder submits more than one bid in this bidding process. However,
this does not limit the participation of subcontractors in more than one
bid; or
(f)
A Bidder who participated as a consultant in the preparation of the
design or technical specifications of the Goods and related services that
are the subject of the bid.
In accordance with Section 47 of the IRR of RA 9184, all Bidding Documents
shall be accompanied by a sworn affidavit of the Bidder that it is not related to
the Head of the Procuring Entity, members of the Bids and Awards Committee
(BAC), members of the Technical Working Group (TWG), members of the
BAC Secretariat, the head of the Project Management Office (PMO) or the
end-user unit, and the project consultants, by consanguinity or affinity up to
the third civil degree. On the part of the Bidder, this Clause shall apply to the
following persons:
(a)
If the Bidder is an individual or a sole proprietorship, to the Bidder
himself;
(b)
If the Bidder is a partnership, to all its officers and members;
(c)
If the Bidder is a corporation, to all its officers, directors, and
controlling stockholders; and
(d)
If the Bidder is a joint venture (JV), the provisions of items (a), (b), or
(c) of this Clause shall correspondingly apply to each of the members
of the said JV, as may be appropriate.
Relationship of the nature described above or failure to comply with this
Clause will result in the automatic disqualification of a Bidder.
11
5.
Eligible Bidders
5.1.
5.2.
Unless otherwise provided in the BDS, the following persons shall be eligible
to participate in this bidding:
(a)
Duly licensed Filipino citizens/sole proprietorships;
(b)
Partnerships duly organized under the laws of the Philippines and of
which at least sixty percent (60%) of the interest belongs to citizens of
the Philippines;
(c)
Corporations duly organized under the laws of the Philippines, and of
which at least sixty percent (60%) of the outstanding capital stock
belongs to citizens of the Philippines;
(d)
Cooperatives duly organized under the laws of the Philippines, and of
which at least sixty percent (60%) of the interest belongs to citizens of
the Philippines; and
(e)
Unless otherwise provided in the BDS, persons/entities forming
themselves into a JV, i.e., a group of two (2) or more persons/entities
that intend to be jointly and severally responsible or liable for a
particular contract: Provided, however, that Filipino ownership or
interest of the joint venture concerned shall be at least sixty percent
(60%).
Foreign bidders may be eligible to participate when any of the following
circumstances exist, as specified in the BDS:
(a)
When a Treaty or International or Executive Agreement as provided in
Section 4 of the RA 9184 and its IRR allow foreign bidders to
participate;
(b)
Citizens, corporations, or associations of a country, included in the list
issued by the GPPB, the laws or regulations of which grant reciprocal
rights or privileges to citizens, corporations, or associations of the
Philippines;
(c)
When the Goods sought to be procured are not available from local
suppliers; or
(d)
When there is a need to prevent situations that defeat competition or
restrain trade.
5.3.
Government corporate entities may be eligible to participate only if they can
establish that they (a) are legally and financially autonomous, (b) operate
under commercial law, and (c) are not dependent agencies of the GOP or the
Procuring Entity.
5.4.
Unless otherwise provided in the BDS, the Bidder must have completed at
least one contract similar to the Project the value of which, adjusted to current
12
prices using the National Statistics Office consumer price index, must be at
least equivalent to a percentage of the ABC stated in the BDS.
For this purpose, contracts similar to the Project shall be those described in the
BDS, and completed within the relevant period stated in the Invitation to Bid
and ITB Clause 12.1(a)(iii).
5.5.
The Bidder must submit a computation of its Net Financial Contracting
Capacity (NFCC) or a commitment from a Universal or Commercial Bank to
extend a credit line in its favor if awarded the contract for this Project (CLC).
The NFCC, computed using the following formula, must be at least equal to
the ABC to be bid:
NFCC = [(Current assets minus current liabilities) (K)] minus the value of
all outstanding or uncompleted portions of the projects under ongoing
contracts, including awarded contracts yet to be started coinciding with the
contract for this Project.
Where:
K = 10 for a contract duration of one year or less, 15 for a contract
duration of more than one year up to two years, and 20 for a contract
duration of more than two years.
The CLC must be at least equal to ten percent (10%) of the ABC for this
Project. If issued by a foreign bank, it shall be confirmed or authenticated by a
Universal or Commercial Bank. In the case of local government units (LGUs),
the Bidder may also submit CLC from other banks certified by the Bangko
Sentral ng Pilipinas (BSP) as authorized to issue such financial instrument.
6.
Bidder’s Responsibilities
6.1.
The Bidder or its duly authorized representative shall submit a sworn
statement in the form prescribed in Section VIII. Bidding Forms as required in
ITB Clause 12.1(b)(iii).
6.2.
The Bidder is responsible for the following:
(a)
Having taken steps to carefully examine all of the Bidding
Documents;
(b)
Having acknowledged all conditions, local or otherwise, affecting the
implementation of the contract;
(c)
Having made an estimate of the facilities available and needed for the
contract to be bid, if any;
(d)
Having complied with its responsibility to inquire or secure
Supplemental/Bid Bulletin(s) as provided under ITB Clause 10.3.
13
(e)
Ensuring that it is not “blacklisted” or barred from bidding by the GOP
or any of its agencies, offices, corporations, or LGUs, including
foreign government/foreign or international financing institution whose
blacklisting rules have been recognized by the GPPB;
(f)
Ensuring that each of the documents submitted in satisfaction of the
bidding requirements is an authentic copy of the original, complete,
and all statements and information provided therein are true and
correct;
(g)
Authorizing the Head of the Procuring Entity or its duly authorized
representative/s to verify all the documents submitted;
(h)
Ensuring that the signatory is the duly authorized representative of the
Bidder, and granted full power and authority to do, execute and
perform any and all acts necessary and/or to represent the Bidder in the
bidding, with the duly notarized Secretary’s Certificate attesting to
such fact, if the Bidder is a corporation, partnership, cooperative, or
joint venture;
(i)
Complying with the disclosure provision under Section 47 of RA 9184
in relation to other provisions of RA 3019; and
(j)
Complying with existing labor laws and standards, in the case of
procurement of services.
Failure to observe any of the above responsibilities shall be at the risk of the
Bidder concerned.
6.3.
The Bidder is expected to examine all instructions, forms, terms, and
specifications in the Bidding Documents.
6.4.
It shall be the sole responsibility of the Bidder to determine and to satisfy itself
by such means as it considers necessary or desirable as to all matters
pertaining to the contract to be bid, including: (a) the location and the nature
of this Project; (b) climatic conditions; (c) transportation facilities; and (d)
other factors that may affect the cost, duration, and execution or
implementation of this Project.
6.5.
The Procuring Entity shall not assume any responsibility regarding erroneous
interpretations or conclusions by the prospective or eligible bidder out of the
data furnished by the procuring entity.
6.6.
The Bidder shall bear all costs associated with the preparation and submission
of his bid, and the Procuring Entity will in no case be responsible or liable for
those costs, regardless of the conduct or outcome of the bidding process.
6.7.
Before submitting their bids, the Bidder is deemed to have become familiar
with all existing laws, decrees, ordinances, acts and regulations of the
Philippines which may affect this Project in any way.
14
6.8.
7.
The Bidder should note that the Procuring Entity will accept bids only from
those that have paid the nonrefundable fee for the Bidding Documents at the
office indicated in the Invitation to Bid.
Origin of Goods
Unless otherwise indicated in the BDS, there is no restriction on the origin of goods
other than those prohibited by a decision of the United Nations Security Council taken
under Chapter VII of the Charter of the United Nations, subject to ITB Clause 27.1.
8.
Subcontracts
8.1.
Unless otherwise specified in the BDS, the Bidder may subcontract portions of
the Goods to an extent as may be approved by the Procuring Entity and stated
in the BDS. However, subcontracting of any portion shall not relieve the
Bidder from any liability or obligation that may arise from the contract for this
Project.
8.2.
Subcontractors must comply with the eligibility criteria and the documentary
requirements specified in the BDS. In the event that any subcontractor is
found by the Procuring Entity to be ineligible, the subcontracting of such
portion of the Goods shall be disallowed.
8.3.
The Bidder may identify the subcontractor to whom a portion of the Goods
will be subcontracted at any stage of the bidding process or during contract
implementation. If the Bidder opts to disclose the name of the subcontractor
during bid submission, the Bidder shall include the required documents as part
of the technical component of its bid.
B. Contents of Bidding Documents
9.
Pre-Bid Conference
9.1.
(a) If so specified in the BDS, a pre-bid conference shall be held at the venue
and on the date indicated therein, to clarify and address the Bidders’ questions
on the technical and financial components of this Project.
(b) The pre-bid conference shall be held at least twelve (12) calendar days
before the deadline for the submission and receipt of bids. If the Procuring
Entity determines that, by reason of the method, nature, or complexity of the
contract to be bid, or when international participation will be more
advantageous to the GOP, a longer period for the preparation of bids is
necessary, the pre-bid conference shall be held at least thirty (30) calendar
days before the deadline for the submission and receipt of bids, as specified in
the BDS.
9.2.
Bidders are encouraged to attend the pre-bid conference to ensure that they
fully understand the Procuring Entity’s requirements. Non-attendance of the
Bidder will in no way prejudice its bid; however, the Bidder is expected to
15
know the changes and/or amendments to the Bidding Documents discussed
during the pre-bid conference.
9.3.
10.
Any statement made at the pre-bid conference shall not modify the terms of
the Bidding Documents unless such statement is specifically identified in
writing as an amendment thereto and issued as a Supplemental/Bid Bulletin.
Clarification and Amendment of Bidding Documents
10.1.
Bidders who have purchased the Bidding Documents may request for
clarification on any part of the Bidding Documents for an interpretation. Such
request must be in writing and submitted to the Procuring Entity at the address
indicated in the BDS at least ten (10) calendar days before the deadline set for
the submission and receipt of bids.
10.2.
Supplemental/Bid Bulletins may be issued upon the Procuring Entity’s
initiative for purposes of clarifying or modifying any provision of the Bidding
Documents not later than seven (7) calendar days before the deadline for the
submission and receipt of bids. Any modification to the Bidding Documents
shall be identified as an amendment.
10.3.
Any Supplemental/Bid Bulletin issued by the BAC shall also be posted on the
Philippine Government Electronic Procurement System (PhilGEPS) and the
website of the Procuring Entity concerned, if available. It shall be the
responsibility of all Bidders who secure the Bidding Documents to inquire and
secure Supplemental/Bid Bulletins that may be issued by the BAC. However,
Bidders who have submitted bids before the issuance of the Supplemental/Bid
Bulletin must be informed and allowed to modify or withdraw their bids in
accordance with ITB Clause 23.
C. Preparation of Bids
11.
Language of Bid
The bid, as well as all correspondence and documents relating to the bid exchanged
by the Bidder and the Procuring Entity, shall be written in English. Supporting
documents and printed literature furnished by the Bidder may be in another language
provided they are accompanied by an accurate translation in English certified by the
appropriate embassy or consulate in the Philippines, in which case the English
translation shall govern for purposes of interpretation of the bid.
12.
Documents Comprising
Components
12.1.
the
Bid:
Eligibility
and
Technical
Unless otherwise indicated in the BDS, the first envelope shall contain the
following eligibility and technical documents:
(a)
Eligibility Documents –
Class “A” Documents:
16
(i)
Registration certificate from the Securities and Exchange
Commission (SEC), Department of Trade and Industry (DTI)
for sole proprietorship, or Cooperative Development Authority
(CDA) for cooperatives, or any proof of such registration as
stated in the BDS;
(ii)
Mayor’s permit issued by the city or municipality where the
principal place of business of the prospective bidder is located;
(iii)
Statement of all its ongoing and completed government and
private contracts within the period stated in the BDS, including
contracts awarded but not yet started, if any. The statement
shall include, for each contract, the following:
(iii.1) name of the contract;
(iii.2) date of the contract;
(iii.3) kinds of Goods;
(iii.4) amount of contract and value of outstanding contracts;
(iii.5) date of delivery; and
(iii.6) end user’s acceptance or official receipt(s) issued for the
contract, if completed.
(iv)
Audited financial statements, stamped “received” by the
Bureau of Internal Revenue (BIR) or its duly accredited and
authorized institutions, for the preceding calendar year, which
should not be earlier than two (2) years from bid submission;
(v)
NFCC computation or CLC in accordance with ITB Clause
5.5; and
Class “B” Document:
(vi)
(b)
If applicable, the JVA in case the joint venture is already in
existence, or duly notarized statements from all the potential
joint venture partners stating that they will enter into and abide
by the provisions of the JVA in the instance that the bid is
successful.
Technical Documents –
(i)
Bid security in accordance with ITB Clause 18. If the Bidder
opts to submit the bid security in the form of:
(i.1)
a bank draft/guarantee or an irrevocable letter of credit
issued by a foreign bank, it shall be accompanied by a
confirmation from a Universal or Commercial Bank; or
17
(i.2)
13.
a surety bond, it shall be accompanied by a certification
by the Insurance Commission that the surety or
insurance company is authorized to issue such
instruments;
(ii)
Conformity with technical specifications, as enumerated and
specified in Sections VI and VII of the Bidding Documents;
and
(iii)
Sworn statement in accordance with Section 25.2(a)(iv) of the
IRR of RA 9184 and using the form prescribed in Section VIII.
Bidding Forms.
Documents Comprising the Bid: Financial Component
13.1.
13.2.
Unless otherwise stated in the BDS, the financial component of the bid shall
contain the following:
(a)
Financial Bid Form, which includes bid prices and the bill of quantities
and the applicable Price Schedules, in accordance with ITB Clauses
15.1 and 15.4;
(b)
If the Bidder claims preference as a Domestic Bidder or Domestic
Entity, a certification from the DTI, SEC, or CDA issued in accordance
with ITB Clause 27, unless otherwise provided in the BDS; and
(c)
Any other document related to the financial component of the bid as
stated in the BDS.
(a)
Unless otherwise stated in the BDS, all bids that exceed the ABC shall
not be accepted.
(b)
Unless otherwise indicated in the BDS, for foreign-funded
procurement, a ceiling may be applied to bid prices provided the
following conditions are met:
(i)
Bidding Documents are obtainable free of charge on a freely
accessible website. If payment of Bidding Documents is required
by the procuring entity, payment could be made upon the
submission of bids.
(ii) The procuring entity has procedures in place to ensure that the
ABC is based on recent estimates made by the responsible unit of
the procuring entity and that the estimates reflect the quality,
supervision and risk and inflationary factors, as well as prevailing
market prices, associated with the types of works or goods to be
procured.
(iii) The procuring entity has trained cost estimators on estimating
prices and analyzing bid variances.
18
(iv) The procuring entity has established a system to monitor and
report bid prices relative to ABC and engineer’s/procuring
entity’s estimate.
(v) The procuring entity has established a system to monitor and
report bid prices relative to ABC and procuring entity’s estimate.
The procuring entity has established a monitoring and evaluation
system for contract implementation to provide a feedback on
actual total costs of goods and works.
14.
Alternative Bids
Alternative Bids shall be rejected. For this purpose, alternative bid is an offer made by
a Bidder in addition or as a substitute to its original bid which may be included as part
of its original bid or submitted separately therewith for purposes of bidding. A bid
with options is considered an alternative bid regardless of whether said bid proposal is
contained in a single envelope or submitted in two (2) or more separate bid envelopes.
15.
Bid Prices
15.1.
The Bidder shall complete the appropriate Price Schedules included herein,
stating the unit prices, total price per item, the total amount and the expected
countries of origin of the Goods to be supplied under this Project.
15.2.
The Bidder shall fill in rates and prices for all items of the Goods described in
the Bill of Quantities. Bids not addressing or providing all of the required
items in the Bidding Documents including, where applicable, Bill of
Quantities, shall be considered non-responsive and, thus, automatically
disqualified. In this regard, where a required item is provided, but no price is
indicated, the same shall be considered as non-responsive, but specifying a "0"
(zero) for the said item would mean that it is being offered for free to the
Government.
15.3.
The terms Ex Works (EXW), Cost, Insurance and Freight (CIF), Cost and
Insurance Paid to (CIP), Delivered Duty Paid (DDP), and other trade terms
used to describe the obligations of the parties, shall be governed by the rules
prescribed in the current edition of the International Commercial Terms
(INCOTERMS) published by the International Chamber of Commerce, Paris.
15.4.
Prices indicated on the Price Schedule shall be entered separately in the
following manner:
(a)
For Goods offered from within the Procuring Entity’s country:
(i)
The price of the Goods quoted EXW (ex works, ex factory, ex
warehouse, ex showroom, or off-the-shelf, as applicable),
including all customs duties and sales and other taxes already
paid or payable:
19
(b)
15.5.
(i.1)
on the components and raw material used in the
manufacture or assembly of Goods quoted ex works or
ex factory; or
(i.2)
on the previously imported Goods of foreign origin
quoted ex warehouse, ex showroom, or off-the-shelf
and any Procuring Entity country sales and other taxes
which will be payable on the Goods if the contract is
awarded.
(ii)
The price for inland transportation, insurance, and other local
costs incidental to delivery of the Goods to their final
destination.
(iii)
The price of other (incidental) services, if any, listed in the
BDS.
For Goods offered from abroad:
(i)
Unless otherwise stated in the BDS, the price of the Goods
shall be quoted DDP with the place of destination in the
Philippines as specified in the BDS. In quoting the price, the
Bidder shall be free to use transportation through carriers
registered in any eligible country. Similarly, the Bidder may
obtain insurance services from any eligible source country.
(ii)
The price of other (incidental) services, if any, listed in the
BDS.
Prices quoted by the Bidder shall be fixed during the Bidder’s performance of
the contract and not subject to variation or price escalation on any account. A
bid submitted with an adjustable price quotation shall be treated as nonresponsive and shall be rejected, pursuant to ITB Clause 24.
All bid prices shall be considered as fixed prices, and therefore not subject to
price escalation during contract implementation, except under extraordinary
circumstances. Extraordinary circumstances refer to events that may be
determined by the National Economic and Development Authority in
accordance with the Civil Code of the Philippines, and upon the
recommendation of the Procuring Entity. Nevertheless, in cases where the cost
of the awarded contract is affected by any applicable new laws, ordinances,
regulations, or other acts of the GOP, promulgated after the date of bid
opening, a contract price adjustment shall be made or appropriate relief shall
be applied on a no loss-no gain basis.
16.
Bid Currencies
16.1.
Prices shall be quoted in the following currencies:
(a)
For Goods that the Bidder will supply from within the Philippines, the
prices shall be quoted in Philippine Pesos.
20
(b)
17.
18.
For Goods that the Bidder will supply from outside the Philippines, the
prices may be quoted in the currency(ies) stated in the BDS. However,
for purposes of bid evaluation, bids denominated in foreign currencies
shall be converted to Philippine currency based on the exchange rate as
published in the BSP reference rate bulletin on the day of the bid
opening.
16.2.
If so allowed in accordance with ITB Clause 16.1, the Procuring Entity for
purposes of bid evaluation and comparing the bid prices will convert the
amounts in various currencies in which the bid price is expressed to Philippine
Pesos at the foregoing exchange rates.
16.3.
Unless otherwise specified in the BDS, payment of the contract price shall be
made in Philippine Pesos.
Bid Validity
17.1.
Bids shall remain valid for the period specified in the BDS which shall not
exceed one hundred twenty (120) calendar days from the date of the opening
of bids.
17.2.
In exceptional circumstances, prior to the expiration of the Bid validity period,
the Procuring Entity may request Bidders to extend the period of validity of
their bids. The request and the responses shall be made in writing. The bid
security described in ITB Clause 18 should also be extended corresponding to
the extension of the bid validity period at the least. A Bidder may refuse the
request without forfeiting its bid security, but his bid shall no longer be
considered for further evaluation and award. A Bidder granting the request
shall not be required or permitted to modify its bid.
Bid Security
18.1.
The bid security in the amount stated in the BDS shall be equal to the
percentage of the ABC in accordance with the following schedule:
Amount of Bid Security
(Equal to Percentage of the ABC)
Form of Bid Security
(a) Cash or cashier’s/manager’s
check issued by a Universal or
Commercial Bank.
(b) Bank
draft/guarantee
or
irrevocable letter of credit issued
by a Universal or Commercial
Bank: Provided, however, that it
shall
be
confirmed
or
authenticated by a Universal or
Commercial Bank, if issued by a
foreign bank.
(c) Surety bond callable upon
demand issued by a surety or
21
Two percent (2%)
Five percent (5%)
insurance company duly certified
by the Insurance Commission as
authorized to issue such security.
(d) Any
combination
of
the
foregoing.
Proportionate to share of form with
respect to total amount of security
For biddings conducted by LGUs, the Bidder may also submit bid securities in
the form of cashier’s/manager’s check, bank draft/guarantee, or irrevocable
letter of credit from other banks certified by the BSP as authorized to issue
such financial statement.
18.2.
The bid security should be valid for the period specified in the BDS. Any bid
not accompanied by an acceptable bid security shall be rejected by the
Procuring Entity as non-responsive.
18.3.
No bid securities shall be returned to bidders after the opening of bids and
before contract signing, except to those that failed or declared as postdisqualified, upon submission of a written waiver of their right to file a motion
for reconsideration and/or protest. Without prejudice on its forfeiture, bid
securities shall be returned only after the bidder with the Lowest Calculated
and Responsive Bid has signed the contract and furnished the performance
security, but in no case later than the expiration of the bid security validity
period indicated in ITB Clause 18.2.
18.4.
Upon signing and execution of the contract pursuant to ITB Clause 32, and the
posting of the performance security pursuant to ITB Clause 33, the successful
Bidder’s bid security will be discharged, but in no case later than the bid
security validity period as indicated in the ITB Clause 18.2.
18.5.
The bid security may be forfeited:
(a)
if a Bidder:
(i)
withdraws its bid during the period of bid validity specified in
ITB Clause 17;
(ii)
does not accept the correction of errors pursuant to ITB Clause
28.3(b);
(iii)
fails to submit the requirements within the prescribed period or
a finding against their veracity as stated in ITB Clause 29.2;
(iv)
submission of eligibility requirements
information or falsified documents;
(v)
submission of bids that contain false information or falsified
documents, or the concealment of such information in the bids
in order to influence the outcome of eligibility screening or any
other stage of the public bidding;
22
containing
false
(vi)
allowing the use of one’s name, or using the name of another
for purposes of public bidding;
(vii)
withdrawal of a bid, or refusal to accept an award, or enter into
contract with the Government without justifiable cause, after
the Bidder had been adjudged as having submitted the Lowest
Calculated and Responsive Bid;
(viii) refusal or failure to post the required performance security
within the prescribed time;
(b)
19.
(ix)
refusal to clarify or validate in writing its bid during postqualification within a period of seven (7) calendar days from
receipt of the request for clarification;
(x)
any documented attempt by a bidder to unduly influence the
outcome of the bidding in his favor;
(xi)
failure of the potential joint venture partners to enter into the
joint venture after the bid is declared successful; or
(xii)
all other acts that tend to defeat the purpose of the competitive
bidding, such as habitually withdrawing from bidding,
submitting late Bids or patently insufficient bid, for at least
three (3) times within a year, except for valid reasons.
if the successful Bidder:
(i)
fails to sign the contract in accordance with ITB Clause 32; or
(ii)
fails to furnish performance security in accordance with ITB
Clause 33.
Format and Signing of Bids
19.1.
Bidders shall submit their bids through their duly authorized representative
using the appropriate forms provided in Section VIII. Bidding Forms on or
before the deadline specified in the ITB Clauses 21 in two (2) separate sealed
bid envelopes, and which shall be submitted simultaneously. The first shall
contain the technical component of the bid, including the eligibility
requirements under ITB Clause 12.1, and the second shall contain the
financial component of the bid.
19.2.
Forms as mentioned in ITB Clause 19.1 must be completed without any
alterations to their format, and no substitute form shall be accepted. All blank
spaces shall be filled in with the information requested.
19.3.
The Bidder shall prepare and submit an original of the first and second
envelopes as described in ITB Clauses 12 and 13. In the event of any
discrepancy between the original and the copies, the original shall prevail.
23
20.
19.4.
The bid, except for unamended printed literature, shall be signed, and each and
every page thereof shall be initialed, by the duly authorized representative/s of
the Bidder.
19.5.
Any interlineations, erasures, or overwriting shall be valid only if they are
signed or initialed by the duly authorized representative/s of the Bidder.
Sealing and Marking of Bids
20.1.
Bidders shall enclose their original eligibility and technical documents
described in ITB Clause 12 in one sealed envelope marked “ORIGINAL TECHNICAL COMPONENT”, and the original of their financial component
in another sealed envelope marked “ORIGINAL - FINANCIAL
COMPONENT”, sealing them all in an outer envelope marked “ORIGINAL
BID”.
20.2.
Each copy of the first and second envelopes shall be similarly sealed duly
marking the inner envelopes as “COPY NO. ___ - TECHNICAL
COMPONENT” and “COPY NO. ___ – FINANCIAL COMPONENT” and
the outer envelope as “COPY NO. ___”, respectively. These envelopes
containing the original and the copies shall then be enclosed in one single
envelope.
20.3.
The original and the number of copies of the Bid as indicated in the BDS shall
be typed or written in indelible ink and shall be signed by the bidder or its duly
authorized representative/s.
20.4.
All envelopes shall:
20.5.
(a)
contain the name of the contract to be bid in capital letters;
(b)
bear the name and address of the Bidder in capital letters;
(c)
be addressed to the Procuring Entity’s BAC in accordance with ITB
Clause 1.1;
(d)
bear the specific identification of this bidding process indicated in the
ITB Clause 1.2; and
(e)
bear a warning “DO NOT OPEN BEFORE…” the date and time for
the opening of bids, in accordance with ITB Clause 21.
If bids are not sealed and marked as required, the Procuring Entity will assume
no responsibility for the misplacement or premature opening of the bid.
D. Submission and Opening of Bids
21.
Deadline for Submission of Bids
Bids must be received by the Procuring Entity’s BAC at the address and on or before
the date and time indicated in the BDS.
24
22.
Late Bids
Any bid submitted after the deadline for submission and receipt of bids prescribed by
the Procuring Entity, pursuant to ITB Clause 21, shall be declared “Late” and shall
not be accepted by the Procuring Entity.
23.
24.
Modification and Withdrawal of Bids
23.1.
The Bidder may modify its bid after it has been submitted; provided that the
modification is received by the Procuring Entity prior to the deadline
prescribed for submission and receipt of bids. The Bidder shall not be allowed
to retrieve its original bid, but shall be allowed to submit another bid equally
sealed, properly identified, linked to its original bid marked as “TECHNICAL
MODIFICATION” or “FINANCIAL MODIFICATION” and stamped
“received” by the BAC. Bid modifications received after the applicable
deadline shall not be considered and shall be returned to the Bidder unopened.
23.2.
A Bidder may, through a Letter of Withdrawal, withdraw its bid after it has
been submitted, for valid and justifiable reason; provided that the Letter of
Withdrawal is received by the Procuring Entity prior to the deadline
prescribed for submission and receipt of bids.
23.3.
Bids requested to be withdrawn in accordance with ITB Clause 23.1 shall be
returned unopened to the Bidders. A Bidder may also express its intention not
to participate in the bidding through a letter which should reach and be
stamped by the BAC before the deadline for submission and receipt of bids. A
Bidder that withdraws its bid shall not be permitted to submit another bid,
directly or indirectly, for the same contract.
23.4.
No bid may be modified after the deadline for submission of bids. No bid may
be withdrawn in the interval between the deadline for submission of bids and
the expiration of the period of bid validity specified by the Bidder on the
Financial Bid Form. Withdrawal of a bid during this interval shall result in the
forfeiture of the Bidder’s bid security, pursuant to ITB Clause 18.5, and the
imposition of administrative, civil and criminal sanctions as prescribed by RA
9184 and its IRR.
Opening and Preliminary Examination of Bids
24.1.
The BAC shall open the first bid envelopes of Bidders in public as specified in
the BDS to determine each Bidder’s compliance with the documents
prescribed in ITB Clause 12. For this purpose, the BAC shall check the
submitted documents of each bidder against a checklist of required documents
to ascertain if they are all present, using a non-discretionary “pass/fail”
criterion. If a bidder submits the required document, it shall be rated “passed”
for that particular requirement. In this regard, bids that fail to include any
requirement or are incomplete or patently insufficient shall be considered as
“failed”. Otherwise, the BAC shall rate the said first bid envelope as “passed”.
24.2.
Unless otherwise specified in the BDS, immediately after determining
compliance with the requirements in the first envelope, the BAC shall
25
forthwith open the second bid envelope of each remaining eligible bidder
whose first bid envelope was rated “passed”. The second envelope of each
complying bidder shall be opened within the same day. In case one or more of
the requirements in the second envelope of a particular bid is missing,
incomplete or patently insufficient, and/or if the submitted total bid price
exceeds the ABC unless otherwise provided in ITB Clause 13.2, the BAC
shall rate the bid concerned as “failed”. Only bids that are determined to
contain all the bid requirements for both components shall be rated “passed”
and shall immediately be considered for evaluation and comparison.
24.3.
Letters of withdrawal shall be read out and recorded during bid opening, and
the envelope containing the corresponding withdrawn bid shall be returned to
the Bidder unopened. If the withdrawing Bidder’s representative is in
attendance, the original bid and all copies thereof shall be returned to the
representative during the bid opening. If the representative is not in
attendance, the bid shall be returned unopened by registered mail. The Bidder
may withdraw its bid prior to the deadline for the submission and receipt of
bids, provided that the corresponding Letter of Withdrawal contains a valid
authorization requesting for such withdrawal, subject to appropriate
administrative sanctions.
24.4.
If a Bidder has previously secured a certification from the Procuring Entity to
the effect that it has previously submitted the above-enumerated Class “A”
Documents, the said certification may be submitted in lieu of the requirements
enumerated in ITB Clause 12.1(a), items (i) to (v).
24.5.
In the case of an eligible foreign Bidder as described in ITB Clause 5, the
Class “A” Documents described in ITB Clause 12.1(a) may be substituted
with the appropriate equivalent documents, if any, issued by the country of the
foreign Bidder concerned.
24.6.
Each partner of a joint venture agreement shall likewise submit the
requirements in ITB Clauses 12.1(a)(i) and 12.1(a)(ii). Submission of
documents required under ITB Clauses 12.1(a)(iii) to 12.1(a)(v) by any of the
joint venture partners constitutes compliance.
24.7.
A Bidder determined as “failed” has three (3) calendar days upon written
notice or, if present at the time of bid opening, upon verbal notification, within
which to file a request or motion for reconsideration with the BAC: Provided,
however, that the motion for reconsideration shall not be granted if it is
established that the finding of failure is due to the fault of the Bidder
concerned: Provided, further, that the BAC shall decide on the request for
reconsideration within seven (7) calendar days from receipt thereof. If a failed
Bidder signifies his intent to file a motion for reconsideration, the BAC shall
keep the bid envelopes of the said failed Bidder unopened and/or duly sealed
until such time that the motion for reconsideration or protest has been
resolved.
24.8.
The Procuring Entity shall prepare the minutes of the proceedings of the bid
opening that shall include, as a minimum: (a) names of Bidders, their bid
26
price, bid security, findings of preliminary examination; and (b) attendance
sheet. The BAC members shall sign the abstract of bids as read.
E. Evaluation and Comparison of Bids
25.
26.
Process to be Confidential
25.1.
Members of the BAC, including its staff and personnel, as well as its
Secretariat and TWG, are prohibited from making or accepting any kind of
communication with any bidder regarding the evaluation of their bids until the
issuance of the Notice of Award, unless otherwise allowed in the case of ITB
Clause 26.
25.2.
Any effort by a bidder to influence the Procuring Entity in the Procuring
Entity’s decision in respect of bid evaluation, bid comparison or contract
award will result in the rejection of the Bidder’s bid.
Clarification of Bids
To assist in the evaluation, comparison, and post-qualification of the bids, the
Procuring Entity may ask in writing any Bidder for a clarification of its bid. All
responses to requests for clarification shall be in writing. Any clarification submitted
by a Bidder in respect to its bid and that is not in response to a request by the
Procuring Entity shall not be considered.
27.
Domestic Preference
27.1.
Unless otherwise stated in the BDS, the Procuring Entity will grant a margin
of preference for the purpose of comparison of bids in accordance with the
following:
(a)
The preference shall be applied when (i) the lowest Foreign Bid is
lower than the lowest bid offered by a Domestic Bidder, or (ii) the
lowest bid offered by a non-Philippine national is lower than the
lowest bid offered by a Domestic Entity.
(b)
For evaluation purposes, the lowest Foreign Bid or the bid offered by a
non-Philippine national shall be increased by fifteen percent (15%).
(c)
In the event that (i) the lowest bid offered by a Domestic Entity does
not exceed the lowest Foreign Bid as increased, or (ii) the lowest bid
offered by a non-Philippine national as increased, then the Procuring
Entity shall award the contract to the Domestic Bidder/Entity at the
amount of the lowest Foreign Bid or the bid offered by a nonPhilippine national, as the case may be.
(d)
If the Domestic Entity/Bidder refuses to accept the award of contract at
the amount of the Foreign Bid or bid offered by a non-Philippine
national within two (2) calendar days from receipt of written advice
from the BAC, the Procuring Entity shall award to the bidder offering
the Foreign Bid or the non-Philippine national, as the case may be,
27
subject to post-qualification and submission of all the documentary
requirements under these Bidding Documents.
28.
27.2.
A Bidder may be granted preference as a Domestic Entity subject to the
certification from the DTI (in case of sole proprietorships), SEC (in case of
partnerships and corporations), or CDA (in case of cooperatives) that the (a)
sole proprietor is a citizen of the Philippines or the partnership, corporation,
cooperative, or association is duly organized under the laws of the Philippines
with at least seventy five percent (75%) of its interest or outstanding capital
stock belonging to citizens of the Philippines, (b) habitually established in
business and habitually engaged in the manufacture or sale of the merchandise
covered by his bid, and (c) the business has been in existence for at least five
(5) consecutive years prior to the advertisement and/or posting of the
Invitation to Bid for this Project.
27.3.
A Bidder may be granted preference as a Domestic Bidder subject to the
certification from the DTI that the Bidder is offering unmanufactured articles,
materials or supplies of the growth or production of the Philippines, or
manufactured articles, materials, or supplies manufactured or to be
manufactured in the Philippines substantially from articles, materials, or
supplies of the growth, production, or manufacture, as the case may be, of the
Philippines.
Detailed Evaluation and Comparison of Bids
28.1.
The Procuring Entity will undertake the detailed evaluation and comparison of
bids which have passed the opening and preliminary examination of bids,
pursuant to ITB Clause 24, in order to determine the Lowest Calculated Bid.
28.2.
The Lowest Calculated Bid shall be determined in two steps:
28.3.
(a)
The detailed evaluation of the financial component of the bids, to
establish the correct calculated prices of the bids; and
(b)
The ranking of the total bid prices as so calculated from the lowest to
the highest. The bid with the lowest price shall be identified as the
Lowest Calculated Bid.
The Procuring Entity's BAC shall immediately conduct a detailed evaluation
of all bids rated “passed,” using non-discretionary pass/fail criteria. Unless
otherwise specified in the BDS, the BAC shall consider the following in the
evaluation of bids:
(a)
Completeness of the bid. Unless the ITB specifically allows partial
bids, bids not addressing or providing all of the required items in the
Schedule of Requirements including, where applicable, bill of
quantities, shall be considered non-responsive and, thus, automatically
disqualified. In this regard, where a required item is provided, but no
price is indicated, the same shall be considered as non-responsive, but
specifying a "0" (zero) for the said item would mean that it is being
offered for free to the Procuring Entity; and
28
(b)
29.
Arithmetical corrections. Consider computational errors and omissions
to enable proper comparison of all eligible bids. It may also consider
bid modifications, if allowed in the BDS. Any adjustment shall be
calculated in monetary terms to determine the calculated prices.
28.4.
Based on the detailed evaluation of bids, those that comply with the abovementioned requirements shall be ranked in the ascending order of their total
calculated bid prices, as evaluated and corrected for computational errors,
discounts and other modifications, to identify the Lowest Calculated Bid.
Total calculated bid prices, as evaluated and corrected for computational
errors, discounts and other modifications, which exceed the ABC shall not be
considered, unless otherwise indicated in the BDS.
28.5.
The Procuring Entity’s evaluation of bids shall only be based on the bid price
quoted in the Financial Bid Form.
28.6.
Bids shall be evaluated on an equal footing to ensure fair competition. For
this purpose, all bidders shall be required to include in their bids the cost of all
taxes, such as, but not limited to, value added tax (VAT), income tax, local
taxes, and other fiscal levies and duties which shall be itemized in the bid form
and reflected in the detailed estimates. Such bids, including said taxes, shall
be the basis for bid evaluation and comparison.
Post-Qualification
29.1.
The Procuring Entity shall determine to its satisfaction whether the Bidder that
is evaluated as having submitted the Lowest Calculated Bid (LCB) complies
with and is responsive to all the requirements and conditions specified in ITB
Clauses 5, 12, and 13.
29.2.
Within a non-extendible period of three (3) calendar days from receipt by the
bidder of the notice from the BAC that it submitted the LCB, the Bidder shall
submit the following documentary requirements:
(a)
Tax clearance per Executive Order 398, Series of 2005;
(b)
Latest income and business tax returns in the form specified in the
BDS;
(c)
Certificate of PhilGEPS Registration; and
(d)
Other appropriate licenses and permits required by law and stated in
the BDS.
Failure of the Bidder declared as Lowest Calculated Bid to duly submit the
requirements under this Clause or a finding against the veracity of such shall
be ground for forfeiture of the bid security and disqualification of the Bidder
for award.
29.3.
The determination shall be based upon an examination of the documentary
evidence of the Bidder’s qualifications submitted pursuant to ITB Clauses 12
29
and 13, as well as other information as the Procuring Entity deems necessary
and appropriate, using a non-discretionary “pass/fail” criterion.
30.
29.4.
If the BAC determines that the Bidder with the Lowest Calculated Bid passes
all the criteria for post-qualification, it shall declare the said bid as the Lowest
Calculated Responsive Bid, and recommend to the Head of the Procuring
Entity the award of contract to the said Bidder at its submitted price or its
calculated bid price, whichever is lower.
29.5.
A negative determination shall result in rejection of the Bidder’s Bid, in which
event the Procuring Entity shall proceed to the next Lowest Calculated Bid to
make a similar determination of that Bidder’s capabilities to perform
satisfactorily. If the second Bidder, however, fails the post qualification, the
procedure for post qualification shall be repeated for the Bidder with the next
Lowest Calculated Bid, and so on until the Lowest Calculated Responsive Bid
is determined for contract award.
29.6.
Within a period not exceeding seven (7) calendar days from the date of receipt
of the recommendation of the BAC, the Head of the Procuring Entity shall
approve or disapprove the said recommendation. In the case of GOCCs and
GFIs, the period provided herein shall be fifteen (15) calendar days.
Reservation Clause
30.1.
Notwithstanding the eligibility or post-qualification of a Bidder, the Procuring
Entity concerned reserves the right to review its qualifications at any stage of
the procurement process if it has reasonable grounds to believe that a
misrepresentation has been made by the said Bidder, or that there has been a
change in the Bidder’s capability to undertake the project from the time it
submitted its eligibility requirements. Should such review uncover any
misrepresentation made in the eligibility and bidding requirements, statements
or documents, or any changes in the situation of the Bidder which will affect
its capability to undertake the project so that it fails the preset eligibility or bid
evaluation criteria, the Procuring Entity shall consider the said Bidder as
ineligible and shall disqualify it from submitting a bid or from obtaining an
award or contract.
30.2.
Based on the following grounds, the Procuring Entity reserves the right to
reject any and all bids, declare a failure of bidding at any time prior to the
contract award, or not to award the contract, without thereby incurring any
liability, and make no assurance that a contract shall be entered into as a result
of the bidding:
(a)
If there is prima facie evidence of collusion between appropriate public
officers or employees of the Procuring Entity, or between the BAC and
any of the Bidders, or if the collusion is between or among the bidders
themselves, or between a Bidder and a third party, including any act
which restricts, suppresses or nullifies or tends to restrict, suppress or
nullify competition;
30
30.3.
(b)
If the Procuring Entity’s BAC is found to have failed in following the
prescribed bidding procedures; or
(c)
For any justifiable and reasonable ground where the award of the
contract will not redound to the benefit of the GOP as follows:
(i)
If the physical and economic conditions have significantly
changed so as to render the project no longer economically,
financially or technically feasible as determined by the head of
the procuring entity;
(ii)
If the project is no longer necessary as determined by the head
of the procuring entity; and
(iii)
If the source of funds for the project has been withheld or
reduced through no fault of the Procuring Entity.
In addition, the Procuring Entity may likewise declare a failure of bidding
when:
(a)
No bids are received;
(b)
All prospective Bidders are declared ineligible;
(c)
All bids fail to comply with all the bid requirements or fail postqualification; or
(d)
The Bidder with the Lowest Calculated Responsive Bid (LCRB)
refuses, without justifiable cause to accept the award of contract, and
no award is made.
F. Award of Contract
31.
Contract Award
31.1.
Subject to ITB Clause 29, the Procuring Entity shall award the contract to the
Bidder whose bid has been determined to be the LCRB.
31.2.
Prior to the expiration of the period of bid validity, the Procuring Entity shall
notify the successful Bidder in writing that its bid has been accepted, through a
Notice of Award received personally or sent by registered mail or
electronically, receipt of which must be confirmed in writing within two (2)
days by the Bidder with the LCRB and submitted personally or sent by
registered mail or electronically to the Procuring Entity.
31.3.
Notwithstanding the issuance of the Notice of Award, award of contract shall
be subject to the following conditions:
(a)
Submission of the valid JVA, if applicable, within ten (10) calendar
days from receipt by the Bidder of the notice from the BAC that the
Bidder has the LCRB;
31
31.4.
32.
33.
(b)
Posting of the performance security in accordance with ITB Clause 33;
(c)
Signing of the contract as provided in ITB Clause 32; and
(d)
Approval by higher authority, if required.
At the time of contract award, the Procuring Entity shall not increase or
decrease the quantity of goods originally specified in Section VI. Schedule of
Requirements.
Signing of the Contract
32.1.
At the same time as the Procuring Entity notifies the successful Bidder that its
bid has been accepted, the Procuring Entity shall send the Contract Form to
the Bidder, which contract has been provided in the Bidding Documents,
incorporating therein all agreements between the parties.
32.2.
Within ten (10) calendar days from receipt of the Notice of Award, the
successful Bidder shall post the required performance security and sign and
date the contract and return it to the Procuring Entity.
32.3.
The Procuring Entity shall enter into contract with the successful Bidder
within the same ten (10) calendar day period provided that all the documentary
requirements are complied with.
32.4.
The following documents shall form part of the contract:
(a)
Contract Agreement;
(b)
Bidding Documents;
(c)
Winning bidder’s bid, including the Technical and Financial Proposals,
and all other documents/statements submitted;
(d)
Performance Security;
(e)
Credit line in accordance with ITB Clause 5.5, if applicable;
(f)
Notice of Award of Contract; and
(g)
Other contract documents that may be required by existing laws and/or
specified in the BDS.
Performance Security
33.1.
To guarantee the faithful performance by the winning Bidder of its obligations
under the contract, it shall post a performance security within a maximum
period of ten (10) calendar days from the receipt of the Notice of Award from
the Procuring Entity and in no case later than the signing of the contract.
32
33.2.
The performance security shall be denominated in Philippine Pesos and posted
in favor of the Procuring Entity in an amount equal to the percentage of the
total contract price in accordance with the following schedule:
Form of Performance Security
(a) Cash or cashier’s/manager’s
check issued by a Universal or
Commercial Bank.
(b) Bank
draft/guarantee
or
irrevocable letter of credit
issued by a Universal or
Commercial Bank: Provided,
however, that it shall be
confirmed or authenticated by a
Universal or Commercial Bank,
if issued by a foreign bank.
(c) Surety bond callable upon
demand issued by a surety or
insurance
company
duly
certified by the Insurance
Commission as authorized to
issue such security; and/or
(d) Any combination of the
foregoing.
33.3.
34.
Amount of Performance Security
(Equal to Percentage of the Total
Contract Price)
Five percent (5%)
(Php57,582.50)
Thirty percent (30%)
(Php345,495.00)
Proportionate to share of form with
respect to total amount of security
Failure of the successful Bidder to comply with the above-mentioned
requirement shall constitute sufficient ground for the annulment of the award
and forfeiture of the bid security, in which event the Procuring Entity shall
initiate and complete the post qualification of the second Lowest Calculated
Bid. The procedure shall be repeated until the LCRB is identified and selected
for contract award. However if no Bidder passed post-qualification, the BAC
shall declare the bidding a failure and conduct a re-bidding with readvertisement.
Notice to Proceed
34.1.
Within three (3) calendar days from the date of approval of the contract by the
appropriate government approving authority, the Procuring Entity shall issue
its Notice to Proceed to the Bidder.
34.2.
The contract effectivity date shall be provided in the Notice to Proceed by the
Procuring Entity, which date shall not be later than seven (7) calendar days
from the issuance of the Notice to Proceed.
33
Section III. Bid Data Sheet
34
Bid Data Sheet
ITB Clause
1.1
The Procuring Entity is PHILIPPINE PORTS AUTHORITY.
1.2
The lot(s) and reference is/are:
Supply and Delivery of Materials for Two (2) Units-175KVA, 220V/460V,
3Phase, 60 Hz Non Polychlorinated Biphenyl (PCB) Transformer with
Complete Accessories at Port of General Santos, Makar Wharf, General
Santos City.
2
The Funding Source is:
The Government of the Philippines (GOP) through THE CORPORATE
BUDGET FOR CY 2013 FOR THE CONTRACT APPROVED BY THE
GOVERNING BOARD in the amount of Php1,702,900.00.
The name of the Project is:
Supply and Delivery of Materials for Two (2) Units-175KVA,
220V/460V, 3Phase, 60 Hz Non Polychlorinated Biphenyl (PCB)
Transformer with Complete Accessories at Port of General Santos, Makar
Wharf, General Santos City .
3.1
No further instructions.
5.1
No further instructions.
5.2
None of the circumstances mentioned in the ITB Clause exists in this
Project. Foreign bidders, except those falling under ITB Clause 5.2(b), may
not participate in this Project.
5.4
For the procurement of Expendable Supplies: The Bidder must have
completed, within the period specified in the Invitation to Bid and ITB
Clause 12.1(a)(iii), a single contract that is similar to this Project,
equivalent to at least twenty-five percent (25%) of the ABC.
7
No further instructions.
8.1
Subcontracting is not allowed.
8.2
Not applicable.
35
9.1
The Procuring Entity will hold a pre-bid conference for this Project on
October 16, 2013 @ 9:00 A.M. at PHILIPPINE PORTS AUTHORITY,
PHIL-AM HALL, MAKAR WHARF, GENERAL SANTOS CITY.
10.1
The Procuring Entity’s address is:
PORT OF GENERAL SANTOS, MAKAR WHARF, GENERAL
SANTOS CITY
12.1(a)
No further instructions.
12.1(a)(i)
“No other acceptable proof of registration is recognized.”
13.1
List any additional requirements or state “No additional requirements.”
13.1(b)
No further instructions.
13.2
The ABC is One Million One Hundred Fifty One Thousand Six
Hundred Fifty Pesos (Php1,151,650.00). Any bid with a financial
component exceeding this amount shall not be accepted.
15.4(a)(iii)
“No incidental services are required.”
15.4(b)
“No incidental services are required.”
16.1(b)
The Bid prices for Goods supplied from outside of the Philippines shall be
quoted in Philippine Peso.
16.3
Not applicable.
17.1
Bids will be valid until 120 Calendar Days from the date of the Bid
Opening.
18.1
The bid security shall be in the following amount:
1. The amount of Php23,033.00 [2% of 1,151,650.00], if bid security is in
cash, cashier’s/manager’s check, bank draft/guarantee or irrevocable
letter of credit;
2. The amount of Php57,582.50 [5% of Php1,151,650.00] if bid security
is in Surety Bond; or
3. Any combination of the foregoing proportionate to the share of form
with respect to total amount of security.
4. Bid Securing Declaration duly notarized.
18.2
The bid security shall be valid until 120 Calendar Days from the date of the
36
Bid Opening.
20.3
Each Bidder shall submit One (1) original and Three (3) copies of the first
and second components of its bid.
21
The address for submission of bids is
LUZ PATRICIA F. TANCO
Chairperson, BAC-PG
Philippine Ports Authority-Port Management Office, Port of General
Santos, Makar Wharf, General Santos City.
The deadline for submission of bids is October 29, 2013@ 1:00P.M.
24.1
The place of bid opening is at Phil-Am Hall, Philippine Ports AuthorityPort Management Office, Port of General Santos, Makar Wharf, General
Santos City.
The date and time of bid opening is October 29, 2013@ 1:30P.M.
24.2
No further instructions.
27.1
No further instructions.
28.3
Not Applicable
28.3(b)
BID MODIFICATION IS NOT ALLOWED.
28.4
No further instructions.
29.2(a)
No further instructions.
29.2(b)
Bidders have the option to submit either manually filed latest tax returns or
tax returns filed through the Electronic Filing and Payments System
(EFPS).
NOTE: The latest income and business tax returns are those within the last
six months preceding the date of bid submission.
29.2(d)
List licenses and permits relevant to the Project and the corresponding law
requiring it.
32.4(g)
List additional contract documents relevant to the Project that may be
required by existing laws and/or the Procuring Entity.
37
Section IV. General Conditions of Contract
38
TABLE OF CONTENTS
1.
DEFINITIONS .............................................................................................. 41
2.
CORRUPT, FRAUDULENT, COLLUSIVE, AND COERCIVE
PRACTICES ................................................................................................. 42
3.
INSPECTION AND AUDIT BY THE FUNDING SOURCE ................................. 43
4.
GOVERNING LAW AND LANGUAGE ........................................................... 43
5.
NOTICES ..................................................................................................... 43
6.
SCOPE OF CONTRACT ................................................................................ 44
7.
SUBCONTRACTING ..................................................................................... 44
8.
PROCURING ENTITY’S RESPONSIBILITIES ................................................ 44
9.
PRICES ....................................................................................................... 44
10. PAYMENT ................................................................................................... 45
11. ADVANCE PAYMENT AND TERMS OF PAYMENT ....................................... 45
12. TAXES AND DUTIES .................................................................................... 46
13. PERFORMANCE SECURITY ........................................................................ 46
14. USE OF CONTRACT DOCUMENTS AND INFORMATION .............................. 46
15. STANDARDS ................................................................................................ 47
16. INSPECTION AND TESTS ............................................................................. 47
17. WARRANTY ................................................................................................ 48
18. DELAYS IN THE SUPPLIER’S PERFORMANCE ............................................ 48
19. LIQUIDATED DAMAGES ............................................................................. 49
20. SETTLEMENT OF DISPUTES ....................................................................... 49
21. LIABILITY OF THE SUPPLIER ..................................................................... 50
22. FORCE MAJEURE ....................................................................................... 50
23. TERMINATION FOR DEFAULT.................................................................... 50
24. TERMINATION FOR INSOLVENCY .............................................................. 51
25. TERMINATION FOR CONVENIENCE ........................................................... 51
26. TERMINATION FOR UNLAWFUL ACTS ...................................................... 52
27. PROCEDURES FOR TERMINATION OF CONTRACTS ................................... 52
28. ASSIGNMENT OF RIGHTS ........................................................................... 53
39
29. CONTRACT AMENDMENT .......................................................................... 53
30. APPLICATION ............................................................................................. 53
40
1.
Definitions
1.1.
In this Contract, the following terms shall be interpreted as indicated:
(a)
“The Contract” means the agreement entered into between the
Procuring Entity and the Supplier, as recorded in the Contract Form
signed by the parties, including all attachments and appendices thereto
and all documents incorporated by reference therein.
(b)
“The Contract Price” means the price payable to the Supplier under the
Contract for the full and proper performance of its contractual
obligations.
(c)
“The Goods” means all of the supplies, equipment, machinery, spare
parts, other materials and/or general support services which the
Supplier is required to provide to the Procuring Entity under the
Contract.
(d)
“The Services” means those services ancillary to the supply of the
Goods, such as transportation and insurance, and any other incidental
services, such as installation, commissioning, provision of technical
assistance, training, and other such obligations of the Supplier covered
under the Contract.
(e)
“GCC” means the General Conditions of Contract contained in this
Section.
(f)
“SCC” means the Special Conditions of Contract.
(g)
“The Procuring Entity” means the organization purchasing the Goods,
as named in the SCC.
(h)
“The Procuring Entity’s country” is the Philippines.
(i)
“The Supplier” means the individual contractor, manufacturer
distributor, or firm supplying/manufacturing the Goods and Services
under this Contract and named in the SCC.
(j)
The “Funding Source” means the organization named in the SCC.
(k)
“The Project Site,” where applicable, means the place or places named
in the SCC.
(l)
“Day” means calendar day.
(m)
The “Effective Date” of the contract will be the date of receipt by the
Supplier of the Notice to Proceed or the date provided in the Notice to
Proceed. Performance of all obligations shall be reckoned from the
Effective Date of the Contract.
41
(n)
2.
“Verified Report” refers to the report submitted by the Implementing
Unit to the Head of the Procuring Entity setting forth its findings as to
the existence of grounds or causes for termination and explicitly stating
its recommendation for the issuance of a Notice to Terminate.
Corrupt, Fraudulent, Collusive, and Coercive Practices
2.1.
Unless otherwise provided in the SCC, the Procuring Entity as well as the
bidders, contractors, or suppliers shall observe the highest standard of ethics
during the procurement and execution of this Contract. In pursuance of this
policy, the Procuring Entity:
(a)
defines, for the purposes of this provision, the terms set forth below as
follows:
(i)
"corrupt practice" means behavior on the part of officials in the
public or private sectors by which they improperly and
unlawfully enrich themselves, others, or induce others to do so,
by misusing the position in which they are placed, and it
includes the offering, giving, receiving, or soliciting of
anything of value to influence the action of any such official in
the procurement process or in contract execution; entering, on
behalf of the Government, into any contract or transaction
manifestly and grossly disadvantageous to the same, whether or
not the public officer profited or will profit thereby, and similar
acts as provided in Republic Act 3019.
(ii)
"fraudulent practice" means a misrepresentation of facts in
order to influence a procurement process or the execution of a
contract to the detriment of the Procuring Entity, and includes
collusive practices among Bidders (prior to or after bid
submission) designed to establish bid prices at artificial, noncompetitive levels and to deprive the Procuring Entity of the
benefits of free and open competition.
(iii)
“collusive practices” means a scheme or arrangement between
two or more Bidders, with or without the knowledge of the
Procuring Entity, designed to establish bid prices at artificial,
non-competitive levels.
(iv)
“coercive practices” means harming or threatening to harm,
directly or indirectly, persons, or their property to influence
their participation in a procurement process, or affect the
execution of a contract;
(v)
“obstructive practice” is
(aa)
deliberately destroying, falsifying, altering or
concealing of evidence material to an administrative
proceedings or investigation or making false statements
to investigators in order to materially impede an
42
administrative proceedings or investigation of the
Procuring Entity or any foreign government/foreign or
international financing institution into allegations of a
corrupt, fraudulent, coercive or collusive practice;
and/or threatening, harassing or intimidating any party
to prevent it from disclosing its knowledge of matters
relevant to the administrative proceedings or
investigation or from pursuing such proceedings or
investigation; or
(bb)
(b)
2.2.
3.
acts intended to materially impede the exercise of the
inspection and audit rights of the Procuring Entity or
any foreign government/foreign or international
financing institution herein.
will reject a proposal for award if it determines that the Bidder
recommended for award has engaged in any of the practices mentioned
in this Clause for purposes of competing for the contract.
Further the Funding Source, Borrower or Procuring Entity, as appropriate, will
seek to impose the maximum civil, administrative and/or criminal penalties
available under the applicable law on individuals and organizations deemed to
be involved with any of the practices mentioned in GCC Clause 2.1(a).
Inspection and Audit by the Funding Source
The Supplier shall permit the Funding Source to inspect the Supplier’s accounts and
records relating to the performance of the Supplier and to have them audited by
auditors appointed by the Funding Source, if so required by the Funding Source.
4.
5.
Governing Law and Language
4.1.
This Contract shall be interpreted in accordance with the laws of the Republic
of the Philippines.
4.2.
This Contract has been executed in the English language, which shall be the
binding and controlling language for all matters relating to the meaning or
interpretation of this Contract. All correspondence and other documents
pertaining to this Contract exchanged by the parties shall be written in
English.
Notices
5.1.
Any notice, request, or consent required or permitted to be given or made
pursuant to this Contract shall be in writing. Any such notice, request, or
consent shall be deemed to have been given or made when received by the
concerned party, either in person or through an authorized representative of
the Party to whom the communication is addressed, or when sent by registered
mail, telex, telegram, or facsimile to such Party at the address specified in the
43
SCC, which shall be effective when delivered and duly received or on the
notice’s effective date, whichever is later.
5.2.
6.
7.
8.
9.
A Party may change its address for notice hereunder by giving the other Party
notice of such change pursuant to the provisions listed in the SCC for GCC
Clause 5.1.
Scope of Contract
6.1.
The GOODS and Related Services to be provided shall be as specified in
Section VI. Schedule of Requirements.
6.2.
This Contract shall include all such items, although not specifically
mentioned, that can be reasonably inferred as being required for its completion
as if such items were expressly mentioned herein.
Any additional
requirements for the completion of this Contract shall be provided in the SCC.
Subcontracting
7.1.
Subcontracting of any portion of the Goods, if allowed in the BDS, does not
relieve the Supplier of any liability or obligation under this Contract. The
Supplier will be responsible for the acts, defaults, and negligence of any
subcontractor, its agents, servants or workmen as fully as if these were the
Supplier’s own acts, defaults, or negligence, or those of its agents, servants or
workmen.
7.2.
Subcontractors disclosed and identified during the bidding may be changed
during the implementation of this Contract, subject to compliance with the
required qualifications and the approval of the Procuring Entity.
Procuring Entity’s Responsibilities
8.1.
Whenever the performance of the obligations in this Contract requires that the
Supplier obtain permits, approvals, import, and other licenses from local
public authorities, the Procuring Entity shall, if so needed by the Supplier,
make its best effort to assist the Supplier in complying with such requirements
in a timely and expeditious manner.
8.2.
The Procuring Entity shall pay all costs involved in the performance of its
responsibilities in accordance with GCC Clause 6.
Prices
9.1.
For the given scope of work in this Contract as awarded, all bid prices are
considered fixed prices, and therefore not subject to price escalation during
contract implementation, except under extraordinary circumstances and upon
prior approval of the GPPB in accordance with Section 61 of R.A. 9184 and
its IRR or except as provided in this Clause.
9.2.
Prices charged by the Supplier for Goods delivered and/or services performed
under this Contract shall not vary from the prices quoted by the Supplier in its
44
bid, with the exception of any change in price resulting from a Change Order
issued in accordance with GCC Clause 29.
10.
11.
Payment
10.1.
Payments shall be made only upon a certification by the Head of the Procuring
Entity to the effect that the Goods have been rendered or delivered in
accordance with the terms of this Contract and have been duly inspected and
accepted. Except with the prior approval of the President no payment shall be
made for services not yet rendered or for supplies and materials not yet
delivered under this Contract. Ten percent (10%) of the amount of each
payment shall be retained by the Procuring Entity to cover the Supplier’s
warranty obligations under this Contract as described in GCC Clause 17.
10.2.
The Supplier’s request(s) for payment shall be made to the Procuring Entity in
writing, accompanied by an invoice describing, as appropriate, the Goods
delivered and/or Services performed, and by documents submitted pursuant to
the SCC provision for GCC Clause 6.2, and upon fulfillment of other
obligations stipulated in this Contract.
10.3.
Pursuant to GCC Clause 10.2, payments shall be made promptly by the
Procuring Entity, but in no case later than sixty (60) days after submission of
an invoice or claim by the Supplier.
10.4.
Unless otherwise provided in the SCC, the currency in which payment is made
to the Supplier under this Contract shall be in Philippine Pesos.
Advance Payment and Terms of Payment
11.1.
Advance payment shall be made only after prior approval of the President, and
shall not exceed fifteen percent (15%) of the Contract amount, unless
otherwise directed by the President or in cases allowed under Annex “D” of
RA 9184.
11.2.
For Goods supplied from abroad, the terms of payment shall be as follows:
(a)
On Contract Signature: Ten percent (10%) of the Contract Price shall
be paid within sixty (60) days from signing of the Contract and upon
submission of a claim and a bank guarantee for the equivalent amount
valid until the Goods are delivered and in the form provided in Section
VIII. Bidding Forms.
(b)
On Delivery: Seventy percent (70%) of the Contract Price shall be paid
to the Supplier within sixty (60) days after the date of receipt of the
Goods and upon submission of the documents (i) through (vi) specified
in the SCC provision on Delivery and Documents.
(c)
On Acceptance: The remaining twenty percent (20%) of the Contract
Price shall be paid to the Supplier within sixty (60) days after the date
of submission of the acceptance and inspection certificate for the
respective delivery issued by the Procuring Entity’s authorized
representative. In the event that no inspection or acceptance certificate
45
is issued by the Procuring Entity’s authorized representative within
forty five (45) days of the date shown on the delivery receipt the
Supplier shall have the right to claim payment of the remaining twenty
percent (20%) subject to the Procuring Entity’s own verification of the
reason(s) for the failure to issue documents (vii) and (viii) as described
in the SCC provision on Delivery and Documents.
11.3.
12.
All progress payments shall first be charged against the advance payment until
the latter has been fully exhausted.
Taxes and Duties
The Supplier, whether local or foreign, shall be entirely responsible for all the
necessary taxes, stamp duties, license fees, and other such levies imposed for the
completion of this Contract.
13.
Performance Security
13.1.
Within ten (10) calendar days from receipt of the Notice of Award from the
Procuring Entity but in no case later than the signing of the contract by both
parties, the successful Bidder shall furnish the performance security in any the
forms prescribed in the ITB Clause 33.2.
13.2.
The performance security posted in favor of the Procuring Entity shall be
forfeited in the event it is established that the winning bidder is in default in
any of its obligations under the contract.
13.3.
The performance security shall remain valid until issuance by the Procuring
Entity of the Certificate of Final Acceptance.
13.4.
The performance security may be released by the Procuring Entity and
returned to the Supplier after the issuance of the Certificate of Final
Acceptance subject to the following conditions:
13.5.
14.
(a)
There are no pending claims against the Supplier or the surety
company filed by the Procuring Entity;
(b)
The Supplier has no pending claims for labor and materials filed
against it; and
(c)
Other terms specified in the SCC.
In case of a reduction of the contract value, the Procuring Entity shall allow a
proportional reduction in the original performance security, provided that any
such reduction is more than ten percent (10%) and that the aggregate of such
reductions is not more than fifty percent (50%) of the original performance
security.
Use of Contract Documents and Information
46
15.
14.1.
The Supplier shall not, except for purposes of performing the obligations in
this Contract, without the Procuring Entity’s prior written consent, disclose
this Contract, or any provision thereof, or any specification, plan, drawing,
pattern, sample, or information furnished by or on behalf of the Procuring
Entity. Any such disclosure shall be made in confidence and shall extend only
as far as may be necessary for purposes of such performance.
14.2.
Any document, other than this Contract itself, enumerated in GCC Clause
14.1 shall remain the property of the Procuring Entity and shall be returned
(all copies) to the Procuring Entity on completion of the Supplier’s
performance under this Contract if so required by the Procuring Entity.
Standards
The Goods provided under this Contract shall conform to the standards mentioned in
the Section VII. Technical Specifications; and, when no applicable standard is
mentioned, to the authoritative standards appropriate to the Goods’ country of origin.
Such standards shall be the latest issued by the institution concerned.
16.
Inspection and Tests
16.1.
The Procuring Entity or its representative shall have the right to inspect and/or
to test the Goods to confirm their conformity to the Contract specifications at
no extra cost to the Procuring Entity. The SCC and Section VII. Technical
Specifications shall specify what inspections and/or tests the Procuring Entity
requires and where they are to be conducted. The Procuring Entity shall notify
the Supplier in writing, in a timely manner, of the identity of any
representatives retained for these purposes.
16.2.
If applicable, the inspections and tests may be conducted on the premises of
the Supplier or its subcontractor(s), at point of delivery, and/or at the goods’
final destination. If conducted on the premises of the Supplier or its
subcontractor(s), all reasonable facilities and assistance, including access to
drawings and production data, shall be furnished to the inspectors at no charge
to the Procuring Entity. The Supplier shall provide the Procuring Entity with
results of such inspections and tests.
16.3.
The Procuring Entity or its designated representative shall be entitled to attend
the tests and/or inspections referred to in this Clause provided that the
Procuring Entity shall bear all of its own costs and expenses incurred in
connection with such attendance including, but not limited to, all traveling and
board and lodging expenses.
16.4.
The Procuring Entity may reject any Goods or any part thereof that fail to pass
any test and/or inspection or do not conform to the specifications. The
Supplier shall either rectify or replace such rejected Goods or parts thereof or
make alterations necessary to meet the specifications at no cost to the
Procuring Entity, and shall repeat the test and/or inspection, at no cost to the
Procuring Entity, upon giving a notice pursuant to GCC Clause 5.
47
16.5.
17.
18.
The Supplier agrees that neither the execution of a test and/or inspection of the
Goods or any part thereof, nor the attendance by the Procuring Entity or its
representative, shall release the Supplier from any warranties or other
obligations under this Contract.
Warranty
17.1.
The Supplier warrants that the Goods supplied under the Contract are new,
unused, of the most recent or current models, and that they incorporate all
recent improvements in design and materials, except when the technical
specifications required by the Procuring Entity provides otherwise.
17.2.
The Supplier further warrants that all Goods supplied under this Contract shall
have no defect, arising from design, materials, or workmanship or from any
act or omission of the Supplier that may develop under normal use of the
supplied Goods in the conditions prevailing in the country of final destination.
17.3.
In order to assure that manufacturing defects shall be corrected by the
Supplier, a warranty shall be required from the Supplier for a minimum period
specified in the SCC. The obligation for the warranty shall be covered by, at
the Supplier’s option, either retention money in an amount equivalent to at
least ten percent (10%) of the final payment, or a special bank guarantee
equivalent to at least ten percent (10%) of the Contract Price or other such
amount if so specified in the SCC. The said amounts shall only be released
after the lapse of the warranty period specified in the SCC; provided,
however, that the Supplies delivered are free from patent and latent defects
and all the conditions imposed under this Contract have been fully met.
17.4.
The Procuring Entity shall promptly notify the Supplier in writing of any
claims arising under this warranty. Upon receipt of such notice, the Supplier
shall, within the period specified in the SCC and with all reasonable speed,
repair or replace the defective Goods or parts thereof, without cost to the
Procuring Entity.
17.5.
If the Supplier, having been notified, fails to remedy the defect(s) within the
period specified in GCC Clause 17.4, the Procuring Entity may proceed to
take such remedial action as may be necessary, at the Supplier’s risk and
expense and without prejudice to any other rights which the Procuring Entity
may have against the Supplier under the Contract and under the applicable
law.
Delays in the Supplier’s Performance
18.1.
Delivery of the Goods and/or performance of Services shall be made by the
Supplier in accordance with the time schedule prescribed by the Procuring
Entity in Section VI. Schedule of Requirements.
18.2.
If at any time during the performance of this Contract, the Supplier or its
Subcontractor(s) should encounter conditions impeding timely delivery of the
Goods and/or performance of Services, the Supplier shall promptly notify the
Procuring Entity in writing of the fact of the delay, its likely duration and its
48
cause(s). As soon as practicable after receipt of the Supplier’s notice, and
upon causes provided for under GCC Clause 22, the Procuring Entity shall
evaluate the situation and may extend the Supplier’s time for performance, in
which case the extension shall be ratified by the parties by amendment of
Contract.
18.3.
19.
Except as provided under GCC Clause 22, a delay by the Supplier in the
performance of its obligations shall render the Supplier liable to the imposition
of liquidated damages pursuant to GCC Clause 19, unless an extension of
time is agreed upon pursuant to GCC Clause 29 without the application of
liquidated damages.
Liquidated Damages
Subject to GCC Clauses 18 and 22, if the Supplier fails to satisfactorily deliver any or
all of the Goods and/or to perform the Services within the period(s) specified in this
Contract inclusive of duly granted time extensions if any, the Procuring Entity shall,
without prejudice to its other remedies under this Contract and under the applicable
law, deduct from the Contract Price, as liquidated damages, the applicable rate of one
tenth (1/10) of one (1) percent of the cost of the unperformed portion for every day of
delay until actual delivery or performance. The maximum deduction shall be ten
percent (10%) of the amount of contract. Once the maximum is reached, the
Procuring Entity shall rescind the Contract pursuant to GCC Clause 23, without
prejudice to other courses of action and remedies open to it.
20.
Settlement of Disputes
20.1.
If any dispute or difference of any kind whatsoever shall arise between the
Procuring Entity and the Supplier in connection with or arising out of this
Contract, the parties shall make every effort to resolve amicably such dispute
or difference by mutual consultation.
20.2.
If after thirty (30) days, the parties have failed to resolve their dispute or
difference by such mutual consultation, then either the Procuring Entity or the
Supplier may give notice to the other party of its intention to commence
arbitration, as hereinafter provided, as to the matter in dispute, and no
arbitration in respect of this matter may be commenced unless such notice is
given.
20.3.
Any dispute or difference in respect of which a notice of intention to
commence arbitration has been given in accordance with this Clause shall be
settled by arbitration. Arbitration may be commenced prior to or after
delivery of the Goods under this Contract.
20.4.
In the case of a dispute between the Procuring Entity and the Supplier, the
dispute shall be resolved in accordance with Republic Act 9285 (“R.A.
9285”), otherwise known as the “Alternative Dispute Resolution Act of 2004.”
20.5.
Notwithstanding any reference to arbitration herein, the parties shall continue
to perform their respective obligations under the Contract unless they
49
otherwise agree; and the Procuring Entity shall pay the Supplier any monies
due the Supplier.
21.
22.
23.
Liability of the Supplier
21.1.
The Supplier’s liability under this Contract shall be as provided by the laws of
the Republic of the Philippines, subject to additional provisions, if any, set
forth in the SCC.
21.2.
Except in cases of criminal negligence or willful misconduct, and in the case
of infringement of patent rights, if applicable, the aggregate liability of the
Supplier to the Procuring Entity shall not exceed the total Contract Price,
provided that this limitation shall not apply to the cost of repairing or
replacing defective equipment.
Force Majeure
22.1.
The Supplier shall not be liable for forfeiture of its performance security,
liquidated damages, or termination for default if and to the extent that the
Supplier’s delay in performance or other failure to perform its obligations
under the Contract is the result of a force majeure.
22.2.
For purposes of this Contract the terms “force majeure” and “fortuitous event”
may be used interchangeably. In this regard, a fortuitous event or force
majeure shall be interpreted to mean an event which the Contractor could not
have foreseen, or which though foreseen, was inevitable. It shall not include
ordinary unfavorable weather conditions; and any other cause the effects of
which could have been avoided with the exercise of reasonable diligence by
the Contractor. Such events may include, but not limited to, acts of the
Procuring Entity in its sovereign capacity, wars or revolutions, fires, floods,
epidemics, quarantine restrictions, and freight embargoes.
22.3.
If a force majeure situation arises, the Supplier shall promptly notify the
Procuring Entity in writing of such condition and the cause thereof. Unless
otherwise directed by the Procuring Entity in writing, the Supplier shall
continue to perform its obligations under the Contract as far as is reasonably
practical, and shall seek all reasonable alternative means for performance not
prevented by the force majeure.
Termination for Default
23.1.
The Procuring Entity shall terminate this Contract for default when any of the
following conditions attends its implementation:
(a)
Outside of force majeure, the Supplier fails to deliver or perform any
or all of the Goods within the period(s) specified in the contract, or
within any extension thereof granted by the Procuring Entity pursuant
to a request made by the Supplier prior to the delay, and such failure
amounts to at least ten percent (10%) of the contact price;
50
24.
(b)
As a result of force majeure, the Supplier is unable to deliver or
perform any or all of the Goods, amounting to at least ten percent
(10%) of the contract price, for a period of not less than sixty (60)
calendar days after receipt of the notice from the Procuring Entity
stating that the circumstance of force majeure is deemed to have
ceased; or
(c)
The Supplier fails to perform any other obligation under the Contract.
23.2.
In the event the Procuring Entity terminates this Contract in whole or in part,
for any of the reasons provided under GCC Clauses 23 to 26, the Procuring
Entity may procure, upon such terms and in such manner as it deems
appropriate, Goods or Services similar to those undelivered, and the Supplier
shall be liable to the Procuring Entity for any excess costs for such similar
Goods or Services. However, the Supplier shall continue performance of this
Contract to the extent not terminated.
23.3.
In case the delay in the delivery of the Goods and/or performance of the
Services exceeds a time duration equivalent to ten percent (10%) of the
specified contract time plus any time extension duly granted to the Supplier,
the Procuring Entity may terminate this Contract, forfeit the Supplier's
performance security and award the same to a qualified Supplier.
Termination for Insolvency
The Procuring Entity shall terminate this Contract if the Supplier is declared bankrupt
or insolvent as determined with finality by a court of competent jurisdiction. In this
event, termination will be without compensation to the Supplier, provided that such
termination will not prejudice or affect any right of action or remedy which has
accrued or will accrue thereafter to the Procuring Entity and/or the Supplier.
25.
Termination for Convenience
25.1.
The Procuring Entity may terminate this Contract, in whole or in part, at any
time for its convenience. The Head of the Procuring Entity may terminate a
contract for the convenience of the Government if he has determined the
existence of conditions that make Project Implementation economically,
financially or technically impractical and/or unnecessary, such as, but not
limited to, fortuitous event(s) or changes in law and national government
policies.
25.2.
The Goods that have been delivered and/or performed or are ready for delivery
or performance within thirty (30) calendar days after the Supplier’s receipt of
Notice to Terminate shall be accepted by the Procuring Entity at the contract
terms and prices. For Goods not yet performed and/or ready for delivery, the
Procuring Entity may elect:
(a)
to have any portion delivered and/or performed and paid at the contract
terms and prices; and/or
51
(b)
25.3.
26.
If the Supplier suffers loss in its initial performance of the terminated contract,
such as purchase of raw materials for goods specially manufactured for the
Procuring Entity which cannot be sold in open market, it shall be allowed to
recover partially from this Contract, on a quantum meruit basis. Before
recovery may be made, the fact of loss must be established under oath by the
Supplier to the satisfaction of the Procuring Entity before recovery may be
made.
Termination for Unlawful Acts
26.1.
27.
to cancel the remainder and pay to the Supplier an agreed amount for
partially completed and/or performed goods and for materials and parts
previously procured by the Supplier.
The Procuring Entity may terminate this Contract in case it is determined
prima facie that the Supplier has engaged, before or during the implementation
of this Contract, in unlawful deeds and behaviors relative to contract
acquisition and implementation. Unlawful acts include, but are not limited to,
the following:
(a)
Corrupt, fraudulent, and coercive practices as defined in ITB Clause
3.1(a);
(b)
Drawing up or using forged documents;
(c)
Using adulterated materials, means or methods, or engaging in
production contrary to rules of science or the trade; and
(d)
Any other act analogous to the foregoing.
Procedures for Termination of Contracts
27.1.
The following provisions shall govern the procedures for termination of this
Contract:
(a)
Upon receipt of a written report of acts or causes which may constitute
ground(s) for termination as aforementioned, or upon its own initiative,
the Implementing Unit shall, within a period of seven (7) calendar
days, verify the existence of such ground(s) and cause the execution of
a Verified Report, with all relevant evidence attached;
(b)
Upon recommendation by the Implementing Unit, the Head of the
Procuring Entity shall terminate this Contract only by a written notice
to the Supplier conveying the termination of this Contract. The notice
shall state:
(i)
that this Contract is being terminated for any of the ground(s)
afore-mentioned, and a statement of the acts that constitute the
ground(s) constituting the same;
(ii)
the extent of termination, whether in whole or in part;
52
28.
(iii)
an instruction to the Supplier to show cause as to why this
Contract should not be terminated; and
(iv)
special instructions of the Procuring Entity, if any.
(c)
The Notice to Terminate shall be accompanied by a copy of the
Verified Report;
(d)
Within a period of seven (7) calendar days from receipt of the Notice
of Termination, the Supplier shall submit to the Head of the Procuring
Entity a verified position paper stating why this Contract should not be
terminated. If the Supplier fails to show cause after the lapse of the
seven (7) day period, either by inaction or by default, the Head of the
Procuring Entity shall issue an order terminating this Contract;
(e)
The Procuring Entity may, at any time before receipt of the Supplier’s
verified position paper described in item (d) above withdraw the
Notice to Terminate if it is determined that certain items or works
subject of the notice had been completed, delivered, or performed
before the Supplier’s receipt of the notice;
(f)
Within a non-extendible period of ten (10) calendar days from receipt
of the verified position paper, the Head of the Procuring Entity shall
decide whether or not to terminate this Contract. It shall serve a
written notice to the Supplier of its decision and, unless otherwise
provided, this Contract is deemed terminated from receipt of the
Supplier of the notice of decision. The termination shall only be based
on the ground(s) stated in the Notice to Terminate;
(g)
The Head of the Procuring Entity may create a Contract Termination
Review Committee (CTRC) to assist him in the discharge of this
function. All decisions recommended by the CTRC shall be subject to
the approval of the Head of the Procuring Entity; and
(h)
The Supplier must serve a written notice to the Procuring Entity of its
intention to terminate the contract at least thirty (30) calendar days
before its intended termination. The Contract is deemed terminated if it
is not resumed in thirty (30) calendar days after the receipt of such
notice by the Procuring Entity.
Assignment of Rights
The Supplier shall not assign his rights or obligations under this Contract, in whole or
in part, except with the Procuring Entity’s prior written consent.
29.
Contract Amendment
Subject to applicable laws, no variation in or modification of the terms of this
Contract shall be made except by written amendment signed by the parties.
30.
Application
53
These General Conditions shall apply to the extent that they are not superseded by
provisions of other parts of this Contract.
54
Section V. Special Conditions of Contract
55
Special Conditions of Contract
GCC Clause
1.1(g)
The Procuring Entity is Philippine Ports Authority-Port Management
Office, Port of General Santos, Makar Wharf, General Santos City.
1.1(i)
The Supplier is [to be inserted at the time of contract award].
1.1(j)
The Funding Source is
the Government of the Philippines (GOP) through THE
CORPORATE BUDGET FOR CY 2013 FOR THE CONTRACT
APPROVED BY THE GOVERNING BOARD in the amount of
Php1,702,900.
1.1(k)
The Project Site is the Port of General Santos, Makar Wharf, General
Santos City.
The Procuring Entity’s address for Notices is:
PORT OF GENERAL SANTOS, MAKAR WHARF, GENERAL
SANTOS CITY
5.1
The Procuring Entity is Philippine Ports Authority-Port Management
Office, Port of General Santos, Makar Wharf, General Santos City.
6.2
List here any additional requirements for the completion of this
Contract.
The following requirements and the corresponding
provisions may be deleted, amended, or retained depending on its
applicability to this Contract:
Delivery and Documents –
For purposes of the Contract, “EXW,” “FOB,” “FCA,” “CIF,” “CIP,”
“DDP” and other trade terms used to describe the obligations of the
parties shall have the meanings assigned to them by the current
edition of INCOTERMS published by the International Chamber of
Commerce, Paris. The Delivery terms of this Contract shall be as
follows:
For Goods Supplied from Within the Philippines, state “The delivery
terms applicable to this Contract are delivered at the Port of General
Santos, Makar Wharf, General Santos City. Risk and title will pass
from the Supplier to the Procuring Entity upon receipt and final
acceptance of the Goods at their final destination.”
Delivery of the Goods shall be made by the Supplier in accordance
with the terms specified in
56
Section VI. Schedule of Requirements. The details of shipping and/or
other documents to be furnished by the Supplier are as follows:
For Goods supplied from within the Philippines:
Upon delivery of the Goods to the Project Site, the Supplier shall
notify the Procuring Entity and present the following documents to
the Procuring Entity:
(i)
Original and four copies of the Supplier’s invoice showing
Goods’ description, quantity, unit price, and total amount;
(ii)
Original and four copies delivery receipt/note, railway receipt,
or truck receipt;
(iii)
Original Supplier’s factory inspection report;
(iv)
Original and four copies of the Manufacturer’s and/or
Supplier’s warranty certificate;
(v)
Original and four copies of the certificate of origin (for
imported Goods);
(vi)
Delivery receipt detailing number and description of items
received signed by the authorized receiving personnel;
(vii)
Certificate of Acceptance/Inspection Report signed by the
Procuring Entity’s representative at the Project Site; and
(viii)
Four copies of the Invoice Receipt for Property signed by the
Procuring Entity’s representative at the Project Site.
For Goods supplied from abroad:
Upon shipment, the Supplier shall notify the Procuring Entity and the
insurance company by cable the full details of the shipment, including
Contract Number, description of the Goods, quantity, vessel, bill of
lading number and date, port of loading, date of shipment, port of
discharge etc. Upon delivery to the Project Site, the Supplier shall
notify the Procuring Entity and present the following documents as
applicable with the documentary requirements of any letter of credit
issued taking precedence:
(i)
Original and four copies of the Supplier’s invoice showing
Goods’ description, quantity, unit price, and total amount;
57
(ii)
Original and four copies of the negotiable, clean shipped on
board bill of lading marked “freight pre-paid” and five copies
of the non-negotiable bill of lading ;
(iii)
Original Supplier’s factory inspection report;
(iv)
Original and four copies of the Manufacturer’s and/or
Supplier’s warranty certificate;
(v)
Original and four copies of the certificate of origin (for
imported Goods);
(vi)
Delivery receipt detailing number and description of items
received signed by the Procuring Entity’s representative at the
Project Site;
(vii)
Certificate of Acceptance/Inspection Report signed by the
Procuring Entity’s representative at the Project Site; and
(viii)
Four copies of the Invoice Receipt for Property signed by the
Procuring Entity’s representative at the Project Site.
For purposes of this Clause the Procuring Entity’s Representative at
the Project Site is Engr. Danilo E. Perez
Incidental Services –
The Supplier is required to provide all of the following services,
including additional services, if any, specified in
Section VI. Schedule of Requirements:
Select appropriate requirements and delete the rest.
(a)
furnishing of a detailed operations and maintenance manual
for each appropriate unit of the supplied Goods;
(b)
performance or supervision or maintenance and/or repair of
the supplied Goods, for a period of time agreed by the parties,
provided that this service shall not relieve the Supplier of any
warranty obligations under this Contract; and
Packaging –
The Supplier shall provide such packaging of the Goods as is required
to prevent their damage or deterioration during transit to their final
58
destination, as indicated in this Contract. The packaging shall be
sufficient to withstand, without limitation, rough handling during
transit and exposure to extreme temperatures, salt and precipitation
during transit, and open storage. Packaging case size and weights
shall take into consideration, where appropriate, the remoteness of the
GOODS’ final destination and the absence of heavy handling
facilities at all points in transit.
The packaging, marking, and documentation within and outside the
packages shall comply strictly with such special requirements as shall
be expressly provided for in the Contract, including additional
requirements, if any, specified below, and in any subsequent
instructions ordered by the Procuring Entity.
The outer packaging must be clearly marked on at least four (4) sides
as follows:
Name of the Procuring Entity
Name of the Supplier
Contract Description
Final Destination
Gross weight
Any special lifting instructions
Any special handling instructions
Any relevant HAZCHEM classifications
A packaging list identifying the contents and quantities of the package
is to be placed on an accessible point of the outer packaging if
practical. If not practical the packaging list is to be placed inside the
outer packaging but outside the secondary packaging.
Insurance –
The Goods supplied under this Contract shall be fully insured by the
Supplier in a freely convertible currency against loss or damage
incidental to manufacture or acquisition, transportation, storage, and
delivery. The Goods remain at the risk and title of the Supplier until
their final acceptance by the Procuring Entity.
Transportation –
Where the Supplier is required under Contract to deliver the Goods
CIF, CIP or DDP, transport of the Goods to the port of destination or
such other named place of destination in the Philippines, as shall be
specified in this Contract, shall be arranged and paid for by the
Supplier, and the cost thereof shall be included in the Contract Price.
59
Where the Supplier is required under this Contract to transport the
Goods to a specified place of destination within the Philippines,
defined as the Project Site, transport to such place of destination in the
Philippines, including insurance and storage, as shall be specified in
this Contract, shall be arranged by the Supplier, and related costs shall
be included in the Contract Price.
Where the Supplier is required under Contract to deliver the Goods
CIF, CIP or DDP, Goods are to be transported on carriers of
Philippine registry. In the event that no carrier of Philippine registry is
available, Goods may be shipped by a carrier which is not of
Philippine registry provided that the Supplier obtains and presents to
the Procuring Entity certification to this effect from the nearest
Philippine consulate to the port of dispatch. In the event that carriers
of Philippine registry are available but their schedule delays the
Supplier in its performance of this Contract the period from when the
Goods were first ready for shipment and the actual date of shipment
the period of delay will be considered force majeure in accordance
with GCC Clause 22.
The Procuring Entity accepts no liability for the damage of Goods
during transit other than those prescribed by INCOTERMS for DDP
Deliveries. In the case of Goods supplied from within the Philippines
or supplied by domestic Suppliers risk and title will not be deemed to
have passed to the Procuring Entity until their receipt and final
acceptance at the final destination.
Patent Rights –
The Supplier shall indemnify the Procuring Entity against all
third-party claims of infringement of patent, trademark, or industrial
design rights arising from use of the Goods or any part thereof.
10.4
13.4(c)
Not applicable.
16.1
No further instructions.
17.3
The inspection and test that will be conducted is: On site inspection
and Continuity Test.
17.4
Three (3) months after acceptance by the Procuring Entity of the
delivered Goods or after the Goods are consumed, whichever is
earlier.
21.1
The period for correction of defects in the warranty period is One (1)
Year from the date of delivery.
60
Section VI. Schedule of Requirements
The delivery schedule expressed as weeks/months stipulates hereafter a delivery date which
is the date of delivery to the project site.
Item
Number
1
Description
175KVA, 220V/460V,
3Phase, 60 Hz Non
Polychlorinated Biphenyl
(PCB) Transformer with
Complete Accessories
Quantity
2
61
Total
2
Delivered,
Weeks/Months
not to exceed thirty
(30) calendar days
Section VII. Technical Specifications
Specifications for the Project Supply and Delivery of Materials for Two(2)-Units
175-KVA, 220V/460V, 3 Phase, 60 Hz, Non Polychlorinated biphenyl (PCB)
Transformer with complete accessories:
30 rolls
30 rolls
6 pieces
50 meters
2 length
24 pieces
12 pieces
25 meters
– 3M Rubber Tape
– 3M PVC Tape
– 500 MCM Solderless Connector
– 500 MCM TW Wire 600V
– 30 cm wide Ladder Type Cable Tray w/ cover & supports
(painted), at 2.50meters each
– 500 MCM Compressor Type Eye Terminal or Equivalent
– 3” long 6 x ½” Φ Stainless Nut & Bolt with plain & lock washers
– 16mm² Bare Copper for grounding
62
Technical Specifications
Item
Specification
Statement of Compliance
Bidders must state here either “Comply”
or “Not Comply” against each of the
individual
parameters
of
each
Specification stating the corresponding
performance parameter of the equipment
offered. Statements of “Comply” or “Not
Comply” must be supported by evidence
in a Bidders Bid and cross-referenced to
that evidence. Evidence shall be in the
form of manufacturer’s un-amended sales
literature, unconditional statements of
specification and compliance issued by the
manufacturer, samples, independent test
data etc., as appropriate. A statement that
is not supported by evidence or is
subsequently found to be contradicted by
the evidence presented will render the Bid
under evaluation liable for rejection. A
statement either in the Bidders statement
of compliance or the supporting evidence
that is found to be false either during Bid
evaluation, post-qualification or the
execution of the Contract may be regarded
as fraudulent and render the Bidder or
supplier liable for prosecution subject to
the provisions of ITB Clause 3.1(a)(ii)
and/or GCC Clause 2.1(a)(ii).
1
175KVA, 220V/460V, 3Phase,
60 Hz Non Polychlorinated
Biphenyl (PCB) Transformer
with Complete Accessories
63
Section VIII. Bidding Forms
64
TABLE OF CONTENTS
BID FORM........................................................................................................... 66
CONTRACT AGREEMENT FORM ........................................................................ 68
OMNIBUS SWORN STATEMENT .......................................................................... 69
65
Bid Form
Date:
To:
MS. EVANGELINE J. CRISTOBAL
Acting Port Manager
Philippine Ports Authority, PMO-General Santos
Makar Wharf, General Santos City
Dear Ms. Cristobal:
Having examined the Bidding Documents including Bid Bulletin Number/s if any, the
receipt of which is hereby duly acknowledged, we, the undersigned, offer to
[supply/deliver/perform] [description of the Goods] in conformity with the said Bidding
Documents for the sum of [total Bid amount in words and figures] or such other sums as may
be ascertained in accordance with the Schedule of Prices attached herewith and made part of
this Bid.
We undertake, if our Bid is accepted, to deliver the goods in accordance with the
delivery schedule specified in the Schedule of Requirements.
If our Bid is accepted, we undertake to provide a performance security in the form,
amounts, and within the times specified in the Bidding Documents.
We agree to abide by this Bid for the Bid Validity Period specified in BDS provision
for ITB Clause 18.2 and it shall remain binding upon us and may be accepted at any time
before the expiration of that period.
Until a formal Contract is prepared and executed, this Bid, together with your written
acceptance thereof and your Notice of Award, shall be binding upon us.
We understand that you are not bound to accept the lowest or any Bid you may receive.
We certify/confirm that we comply with the eligibility requirements as per ITB Clause
5 of the Bidding Documents.
Dated this ________________ day of ________________ 20______.
[signature]
[in the capacity of]
Duly authorized to sign Bid for and on behalf of
66
____________________________
Bid Proposal
Name of Bidder ________________________________________________
1
2
3
4
5
6
Item
Description
Country of
origin
Quantity
Unit price
per item
Total price
67
Contract Agreement Form
THIS AGREEMENT made the _____ day of __________ 20_____ between [name of
PROCURING ENTITY] of the Philippines (hereinafter called “the Entity”) of the one part and
[name of Supplier] of [city and country of Supplier] (hereinafter called “the Supplier”) of the
other part:
WHEREAS the Entity invited Bids for certain goods and ancillary services, viz.,
[brief description of goods and services] and has accepted a Bid by the Supplier for the
supply of those goods and services in the sum of [contract price in words and figures]
(hereinafter called “the Contract Price”).
NOW THIS AGREEMENT WITNESSETH AS FOLLOWS:
1.
In this Agreement words and expressions shall have the same meanings as are
respectively assigned to them in the Conditions of Contract referred to.
2.
The following documents shall be deemed to form and be read and construed as part
of this Agreement, viz.:
(a)
(b)
(c)
(d)
(e)
(f)
the Bid Form and the Price Schedule submitted by the Bidder;
the Schedule of Requirements;
the Technical Specifications;
the General Conditions of Contract;
the Special Conditions of Contract; and
the Entity’s Notification of Award.
3.
In consideration of the payments to be made by the Entity to the Supplier as
hereinafter mentioned, the Supplier hereby covenants with the Entity to provide the goods
and services and to remedy defects therein in conformity in all respects with the provisions of
the Contract
4.
The Entity hereby covenants to pay the Supplier in consideration of the provision of
the goods and services and the remedying of defects therein, the Contract Price or such other
sum as may become payable under the provisions of the contract at the time and in the
manner prescribed by the contract.
IN WITNESS whereof the parties hereto have caused this Agreement to be executed
in accordance with the laws of the Republic of the Philippines on the day and year first above
written.
Signed, sealed, delivered by
the
(for the Entity)
Signed, sealed, delivered by
the
(for the Supplier).
68
Omnibus Sworn Statement
REPUBLIC OF THE PHILIPPINES )
CITY/MUNICIPALITY OF ______ ) S.S.
AFFIDAVIT
I, [Name of Affiant], of legal age, [Civil Status], [Nationality], and residing at [Address
of Affiant], after having been duly sworn in accordance with law, do hereby depose and state
that:
1. Select one, delete the other:
If a sole proprietorship: I am the sole proprietor of [Name of Bidder] with office
address at [address of Bidder];
If a partnership, corporation, cooperative, or joint venture: I am the duly authorized
and designated representative of [Name of Bidder] with office address at [address of
Bidder];
2. Select one, delete the other:
If a sole proprietorship: As the owner and sole proprietor of [Name of Bidder], I have
full power and authority to do, execute and perform any and all acts necessary to
represent it in the bidding for [Name of the Project] of the [Name of the Procuring
Entity];
If a partnership, corporation, cooperative, or joint venture: I am granted full power
and authority to do, execute and perform any and all acts necessary and/or to
represent the [Name of Bidder] in the bidding as shown in the attached [state title of
attached document showing proof of authorization (e.g., duly notarized Secretary’s
Certificate issued by the corporation or the members of the joint venture)];
3. [Name of Bidder] is not “blacklisted” or barred from bidding by the Government of
the Philippines or any of its agencies, offices, corporations, or Local Government
Units, foreign government/foreign or international financing institution whose
blacklisting rules have been recognized by the Government Procurement Policy
Board;
4. Each of the documents submitted in satisfaction of the bidding requirements is an
authentic copy of the original, complete, and all statements and information provided
therein are true and correct;
5. [Name of Bidder] is authorizing the Head of the Procuring Entity or its duly
authorized representative(s) to verify all the documents submitted;
6. Select one, delete the rest:
69
If a sole proprietorship: I am not related to the Head of the Procuring Entity,
members of the Bids and Awards Committee (BAC), the Technical Working Group,
and the BAC Secretariat, the head of the Project Management Office or the end-user
unit, and the project consultants by consanguinity or affinity up to the third civil
degree;
If a partnership or cooperative: None of the officers and members of [Name of
Bidder] is related to the Head of the Procuring Entity, members of the Bids and
Awards Committee (BAC), the Technical Working Group, and the BAC Secretariat,
the head of the Project Management Office or the end-user unit, and the project
consultants by consanguinity or affinity up to the third civil degree;
If a corporation or joint venture: None of the officers, directors, and controlling
stockholders of [Name of Bidder] is related to the Head of the Procuring Entity,
members of the Bids and Awards Committee (BAC), the Technical Working Group,
and the BAC Secretariat, the head of the Project Management Office or the end-user
unit, and the project consultants by consanguinity or affinity up to the third civil
degree;
7. [Name of Bidder] complies with existing labor laws and standards; and
8. [Name of Bidder] is aware of and has undertaken the following responsibilities as a
Bidder:
a) Carefully examine all of the Bidding Documents;
b) Acknowledge all conditions, local or otherwise, affecting the implementation of
the Contract;
c) Made an estimate of the facilities available and needed for the contract to be bid,
if any; and
d) Inquire or secure Supplemental/Bid Bulletin(s) issued for the [Name of the
Project].
IN WITNESS WHEREOF, I have hereunto set my hand this __ day of ___, 20__ at
____________, Philippines.
_____________________________________
Bidder’s Representative/Authorized Signatory
Subscribed and Sworn to before me this ____ of _______ 2013 with the affiant exhibiting to
me his/her identification card bearing his/her signature and photograph.
Doc. No. ____
Page No. _____
Book No. ____
Series of 2013.
70
71