Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
This Product MasterSpec Section is licensed by ARCOM to AJW Architectural Products ("Licensee").
This Product MasterSpec Section modifies the original MasterSpec text, and does not include the
full content of the original MasterSpec Section.
Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by,
or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither
AIA nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec
Section by any end user. A qualified design professional should review and edit the document to suit
project requirements.
For more information, contact AJW Architectural Products, 509 Temple Hill Road, New Windsor, NY
12553; Phone: (845) 562-3332; Fax: (845) 562-3391; Website: www.ajw.com; Email: specs@ajw.com.
For information about MasterSpec contact ARCOM at (800) 424-5080 or visit www.MasterSpec.com.
SECTION 101200 - DISPLAY CASES
TIPS:
To view non-printing Editor's Notes that provide guidance for editing, click on Masterworks/Single-File
Formatting/Toggle/Editor's Notes.
To read detailed research, technical information about products and materials, and coordination
checklists, click on Masterworks/Supporting Information.
PART 1 - GENERAL
1.1
RELATED DOCUMENTS
A.
1.2
Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
SUMMARY
A.
Section Includes:
1.
2.
B.
Bulletin Boards.
Display Cases.
Related Requirements:
1.
2.
3.
Section 06100 "Rough Carpentry" for proper blocking and other anchorages required to
sustain bulletin boards and display cases.
Section 064113 "Wood-Veneer-Faced Architectural Cabinets" for custom wood display
cases.
Section 097723 "Fabric-Wrapped Panels" for tackable, fabric-covered wall panels.
DISPLAY CASES
101200 - 1
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
4.
5.
1.3
Section 101100 "Visual Display Units" for markerboards and tackboards.
Section 101300 "Directories" for boards with changeable messages and letters, and for
bulletin boards within built-in directories.
DEFINITIONS
A.
Bulletin Board: Glazed cabinet with tackable surface panel, without shelves, typically of
shallow depth for display of paper documents.
B.
Display Case: Glazed cabinet with or without optional tackable back panel, and adjustable
shelves.
C.
Tackable Panel: A material for holding push-pins or tacks typically consisting of a facing, such
as fabric, vinyl, or cork; adhered to a substrate, such as fiberboard, hardboard, particleboard.
1.4
REFERENCES
A.
ASTM B 221: Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars,
Rods, Wire, Profiles, and Tubes.
B.
ASTM E 84: Standard Test Method for Surface Burning Characteristics for Building Materials.
C.
ASTM C 208: Standard Specification for Cellulosic Fiber Insulating Board.
D.
ASTM C 1048: Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass.
E.
ANSI A 135.4: Tempered Hardboard.
F.
Federal Specifications (FS) CCC-W-408D - Wall Covering, Vinyl Coated.
G.
HPVA HP-1: Hardwood Plywood.
H.
NEMA LD 3: High Pressure Laminate.
1.5
ACTION SUBMITTALS
A.
Product Data:
1.
2.
B.
Include manufacturer's technical data sheets, outlining construction details, material
descriptions, dimensions of individual components and profiles, finishes and accessories
for [display cases] [and] [bulletin boards].
Include electrical characteristics for illuminated [display cases] [and] [bulletin boards].
LEED Submittals:
1.
Laboratory Test Reports for Credit IEQ 4.1: For adhesives, documentation indicating that
products comply with the testing and product requirements of the California Department
of Public Health's (formerly, the California Department of Health Services') "Standard
DISPLAY CASES
101200 - 2
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
2.
3.
C.
Shop Drawings: For [display cases] [and] [bulletin boards].
1.
2.
3.
4.
5.
D.
Include dimensioned plans, elevations, details, and attachment(s) to other work.
Show anchors and accessories.
Show location of seams and joints in tackboard panels.
Include sections of typical trim members.
Include diagrams for wiring of illuminated [display cases] [and] [bulletin boards].
Samples for Initial Selection:
1.
1.6
Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from
Indoor Sources Using Environmental Chambers."
Product Data for Credit IEQ 4.4: For composite wood products, documentation indicating
that the product contains no urea formaldehyde.
Laboratory Test Reports for Credit IEQ 4.4: For composite wood products used in
[display cases] [and] [bulletin boards], documentation indicating that products comply
with the testing and product requirements of the California Department of Public Health's
(formerly, the California Department of Health Services') "Standard Method for the
Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources
Using Environmental Chambers."
Provide swatches of tackable material, showing colors and textures.
CLOSEOUT SUBMITTALS
A.
1.7
Maintenance Data: Provide manufacturer's standard care and cleaning instructions, installation
guide, and a clean copy of the final approved shop drawings for owner's records.
DELIVERY, STORAGE, AND HANDLING
A.
Ship product upright in a manner providing proper protection.
B.
Do not remove factory-installed protective covering for [display cases] [and] [bulletin boards]
until after installation.
1.8
PROJECT CONDITIONS
A.
Environmental Limitations: Do not deliver or install [display cases] [and] [bulletin boards] for
indoor installations until spaces are enclosed and weathertight, wet-work in spaces is complete
and dry, work above ceilings is complete, and temporary HVAC system is operating and
maintaining ambient temperature and humidity conditions at occupancy levels during the
remainder of the construction period.
B.
Field Measurements: Verify actual dimensions of construction relevant to [display cases] [and]
[bulletin boards] prior to fabrication.
DISPLAY CASES
101200 - 3
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
PART 2 - PRODUCTS
2.1
MANUFACTURERS
A.
2.2
Source Limitations: Obtain [display cases] [and] [bulletin boards] from single source from
single manufacturer.
PERFORMANCE REQUIREMENTS
A.
Surface-Burning Characteristics: Comply with ASTM E 84; testing by a qualified independent
testing agency. Identify products with appropriate markings of applicable testing agency.
1.
2.
B.
2.3
Flame-Spread Index: [25] <Insert value> or less.
Smoke-Developed Index: Less than 450.
Electrical Components: Listed and labeled as defined in NFPA 70, by a qualified independent
testing agency, and marked for intended location and application.
BULLETIN BOARDS <Insert unique drawing designation>
A.
Basis-of-Design Product: Subject to compliance with requirements, provide AJW Architectural
Products; AJW Bulletin Boards or comparable product by one of the following:
1.
<Insert manufacturer's name>.
B.
Substitutions: [Under provisions of Division 01.] [Not permitted.]
C.
General: Factory-fabricated unit consisting of manufacturer's standard cabinet with tackable
panel on back inside surface and operable glazed doors at front.
1.
2.
3.
D.
a.
Surface Mounted Units: Secured by means of Z-bar hangers.
b.
Recessed Units: Secured into rough wall opening.
Size: [As indicated on Drawings.] [Manufacturer's standard size:] <Insert
dimensions>.
Aluminum-Framed Cabinet: Extruded aluminum; 3 inch (76 mm) perimeter trim, with [clear
anodized] [manufacturer's standard powder-coated] finish.
1.
E.
Frame and Cabinet Profile: Square frame section with square cabinet corners.
Mounting: [Surface mounted] [Recessed].
Color: [White] [Black] [Dark Bronze] [Match Architect's sample] <Insert color>.
Back Panel: Tackable panel consisting of [natural cork] [colored cork] [Type I vinyl] [Type
II vinyl] [designer polyester fabric] on substrate.
1.
Color and Pattern: [As selected by Architect from full range of manufacturer's colors]
<Insert color>.
DISPLAY CASES
101200 - 4
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
F.
Glazed Sliding Doors: [Tempered unframed safety glass] [Plastic acrylic sheet, unframed];
with extruded-aluminum top and bottom sliding tracks and ball-bearing rollers. Each door
equipped with plastic top guide, rubber bumpers, ground finger pull and keyed ratchet-type
tumbler locks.
1.
2.
G.
Thickness: [3/16 inch (5 mm)] <Insert dimension> thick.
Number of Doors: [One] [Two] [Three] [As indicated on Drawings] <Insert
number>.
Glazed Hinged Doors: [Tempered safety glass] [Plastic acrylic sheet]; set in frame matching
cabinet material and finish. Equip each door with full-height continuous piano hinges and keyed
tumbler locks..
1.
2.
Thickness: [3/16 inch (5 mm)] <Insert dimension> thick.
Number of Doors: [One] [Two] [Three] [As indicated on Drawings] <Insert
number>.
H.
Header Panel: 6 inch (152 mm) translucent plexiglass panel; with matching frame that
separates header panel from bulletin board.
I.
Illumination System: Concealed fluorescent-strip fixtures, including lamps and internal wiring
with single connection to building system.
1.
Ballasts: Low-temperature, high-power-factor, low-energy, fluorescent lamp ballasts that
comply with Certified Ballast Manufacturers Association standards and carry its label.
a.
2.4
Electrical Characteristics: Single-phase, [120] [230] [277] volts.
DISPLAY CASES <Insert unique drawing designation>
A.
Basis-of-Design Product: Subject to compliance with requirements, provide AJW Architectural
Products; AJW Display Cases or comparable product by one of the following:
1.
<Insert manufacturer's name>.
B.
Substitutions: [Under provisions of Division 01.] [Not permitted.]
C.
General: Factory-fabricated display case; with finished interior and operable glazed doors at
front, and trim on face to cover edge of recessed opening.
1.
2.
3.
D.
Frame Profile: Trim, 2 inch (51 mm), with mitered corners.
Mounting: Recessed.
Size: [As indicated on Drawings] [Manufacturer's standard size] <Insert
dimensions>.
Recessed Display Case:
1.
Display Case Cabinet: [Extruded aluminum box] [Wood laminate plywood box]
[Owner furnished].
DISPLAY CASES
101200 - 5
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
a.
2.
3.
Face Frame: Extruded aluminum.
Aluminum Finish: [Clear anodized] [Manufacturer's standard powder coat] finish.
a.
E.
Veneer and Finish: [Natural Maple] [Amber Maple] [Wild Cherry] [Select
Cherry] [Mahogany] [Walnut] [Manufacturer's Standard].
Color: [White] [Dark bronze] [Black] [Match Architect's sample] <Insert
color>.
Back Panel: Tackable panel consisting of [natural cork] [colored cork] [Type I vinyl] [Type
II vinyl] [designer polyester fabric] on substrate.
1.
Color: [As selected by Architect from full range of manufacturer's colors] <Insert
color>.
F.
Back Panel: Wood veneer finished; [Manufacturer's Standard] [Natural Maple] [Amber
Maple] [Wild Cherry] [Select Cherry] [Mahogany] [Walnut].
G.
Back Panel: None.
H.
Side Panels:
1.
2.
I.
Glazed Sliding Doors: [Tempered safety glass] [Plastic acrylic sheet]; unframed; with
extruded-aluminum top and bottom sliding tracks and ball-bearing rollers. Each door equipped
with plastic top guide and rubber bumpers, ground finger pull, and keyed ratchet-type tumbler
locks.
1.
2.
J.
Thickness: [3/16 inch (5 mm)] <Insert dimension> thick.
Number of Doors: [One] [Two] [Three] [As indicated on Drawings] <Insert
number>.
Shelves: 3/16 inch (5 mm) thick tempered glass; supported on adjustable shelf standards that
extend the full height of display case.
1.
2.
L.
Thickness: [3/16 inch (5 mm)] <Insert dimension> thick.
Number of Doors: [Two] [Three] [As indicated on Drawings] <Insert number>.
Glazed Hinged Doors: [Tempered safety glass] [Plastic acrylic sheet]; set in frame matching
cabinet material and finish. Equip each door with full-height continuous piano hinges and keyed
tumbler locks.
1.
2.
K.
Wood Veneer Finish: [Manufacturer's Standard] [Natural Maple] [Amber Maple]
[Wild Cherry] [Select Cherry] [Mahogany] [Walnut].
None.
Shelf Depth: [6 inches (150 mm)] [8 inches (200 mm)] [10 inches (250 mm)] [12
inches (300 mm)].
Number of Shelves: Two sets of three shelves..
Illumination System: Concealed fluorescent fixtures, including lamps and internal wiring with
single connection to building system.
DISPLAY CASES
101200 - 6
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
1.
Ballasts: Low-temperature, high-power-factor, low-energy, fluorescent lamp ballasts that
comply with Certified Ballast Manufacturers Association standards and carry its label.
a.
2.5
Electrical Characteristics: Single phase, [120] [230] [277] volts.
TACKABLE PANELS
A.
Natural Cork: [1/4 inch- (6.4 mm) thick, on 1/4-inch (6.4-mm) thick hardboard core] [1/8
inch (3.2 mm) thick, on 3/8 inch (9.5 mm) thick fiberboard core]; seamless, single-layer,
compressed fine grain cork sheet; bulletin board quality; face sanded for a natural finish[, with
surface-burning characteristics indicated].
B.
Colored Cork: 1/4 inch (6.4 mm) thick, seamless, homogeneous, self-cleaning sheet consisting
of granulated cork, linseed oil, resin binders, and dry pigments that are mixed and calendared
onto fabric backing; with washable vinyl finish, and integral color throughout[, with surfaceburning characteristics indicated]. Affixed to 1/4 inch (6.4 mm) thick hardboard core.
C.
Vinyl Fabric: Mildew resistant, washable vinyl, complying with FS CCC-W-408D, [Type I]
[Type II]. <Insert texture or pattern>; with surface-burning characteristics indicated. Affixed
to [1/4 inch- (6.4 mm) thick natural cork, on 1/4-inch (6.4-mm) thick hardboard] [1/2 inch
(12.7 mm) thick fiberboard] [1/8 inch (3.2 mm) thick natural cork, on 3/8 inch (9.5 mm)
thick fiberboard] core.
D.
Designer Fabric: Non-directional weave, 100 percent polyester; with surface-burning
characteristics indicated. Affixed to [1/4 inch- (6.4 mm) thick natural cork, on 1/4-inch (6.4mm) thick hardboard] [1/2 inch (12.7 mm) thick fiberboard] [1/8 inch (3.2 mm) thick
natural cork, on 3/8 inch (9.5 mm) thick fiberboard] core.
2.6
MATERIALS
A.
Hardboard: ANSI A135.4, tempered.
B.
Fiberboard: ASTM C 208.
C.
Hardwood Plywood: HPVA HP-1[.][, made with adhesive containing no urea
formaldehyde.][, that complies with the testing and product requirements of the
California Department of Public Health's (formerly, the California Department of Health
Services') "Standard Method for the Testing and Evaluation of Volatile Organic Chemical
Emissions from Indoor Sources Using Environmental Chambers."]
D.
Extruded-Aluminum: ASTM B 221 (ASTM B 221M), Alloy 6063-T5.
E.
Clear Tempered Glass: ASTM C 1048, Kind FT, Condition A, Type I, Class 1, Quality Q3, with
exposed edges seamed before tempering.
F.
High-Pressure Plastic Laminate: NEMA LD 3.
G.
Fasteners: Provide types, sizes, and lengths to suit installation conditions; head finish to match
frame where exposed..
DISPLAY CASES
101200 - 7
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
2.7
FABRICATION
A.
Fabricate [bulletin boards] [and] [display cases] to requirements indicated for dimensions,
design, and thickness and finish of materials.
B.
Use metals and shapes of thickness and reinforcing required to produce flat surfaces, and to
impart strength for size, design, and application indicated.
C.
Fabricate cabinets and door frames with reinforced corners, mitered to a hairline fit, with no
exposed fasteners.
D.
Fabricate shelf standards plumb and at heights to align shelf brackets for level shelves.
E.
Factory assemble units.
2.8
GENERAL FINISH REQUIREMENTS
A.
Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for
recommendations for applying and designating finishes.
B.
Protect mechanical finishes on exposed surfaces from damage by applying a strippable,
temporary protective covering before shipping.
C.
Appearance of Finished Work: Noticeable variations in same piece are unacceptable. Variations
in appearance of adjoining components are acceptable if they are within the range of approved
Samples and are assembled or installed to minimize contrast.
2.9
ALUMINUM FINISHES
A.
Clear Anodized Finish: AAMA 611, AA-M12C22A31, Class II, 0.010 mm or thicker.
B.
Powder-Coat Finish: AAMA 2603, except with a minimum dry film thickness of 1.5 mils (0.04
mm). Comply with coating manufacturer's written instructions for cleaning, conversion coating,
and applying and baking finish.
PART 3 - EXECUTION
3.1
EXAMINATION
A.
Examine all work areas and verify that all applicable measurements, structural supports,
backing, and environmental conditions are in accordance with manufacturer's prerequisites for
installation.
B.
Proceed with installation only after the above criteria is met.
DISPLAY CASES
101200 - 8
Copyright 2013 AIA
MasterSpec Premium
09/13
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AJW ARCHITECTURAL PRODUCTS.
3.2
PREPARATION
A.
3.3
Prepare recesses for display cases as required by type and size of unit.
INSTALLATION
A.
General: Install [display cases] [and] [bulletin boards] in accordance with manufacturer's
instructions, including proper wall surface preparation.
B.
Set plumb and level, with perimeter trim straight.
C.
Install units in locations and at mounting heights indicated on Drawings, or if not indicated, at
heights indicated below. Provide grounds, clips, backing materials, adhesives, brackets,
anchors, trim, and accessories necessary for complete installation.
1.
Mounting Height: [72 inches (1829 mm)] <Insert dimension> above finished floor to
top of cabinet.
D.
Attach units to wall surfaces with concealed fasteners.
E.
Recessed Display Cases: Attach units to wall framing with fasteners at not more than 16 inches
(400 mm) o.c. Attach aluminum trim over edges of recessed display cases and conceal grounds
and clips. Attach trim with fasteners at not more than 24 inches (600 mm) o.c.
F.
Comply with requirements specified elsewhere for connecting illuminated [bulletin boards]
[and] [display cases].
G.
Install display case shelving level and straight.
3.4
FINAL CLEANUP
A.
Remove temporary protective coatings.
B.
Clean surfaces in accordance with manufacturer's instructions.
C.
Legally dispose of all packaging and construction debris.
END OF SECTION 101200
DISPLAY CASES
101200 - 9