Paintworks Specification 6711W - Exterior new miscellaneous substrates
Page 1 of 2
Description area
EXTERIOR ALUMINIUM AND COPPER
Surface Preparation: Refer to Masterspec Section 6700W Wattyl Taubmans Painting General for product clauses
Valspar Paint (NZ) Ltd provides recommended generic coating systems for various applications. Some substrate manufacturers
have their own recommended coating system. In these cases the substrate manufacturer's recommendations take precedence
over the Wattyl Taubmans Granosite coating system and products must be selected to satisfy the substrate manufacturer's
recommendations.
Cut and paste the coating system that meets to your requirements and paste into your Masterspec document
Coating type:
Solvent based premium clear finish
Gloss levels: Gloss
1st coat:
Incralac (Clear Copper Coating)
2nd coat:
Incralac (Clear Copper Coating)
3rd coat:
Incralac (Clear Copper Coating)
General metal steelwork: handrails, bracketing, framing etc.
Coating type:
Water based premium acrylic enamel finish
Gloss levels: ~
1st coat:
Wattyl Killrust Super Etch
2nd coat:
Taubmans UltraProof Acrylic Enamel
3rd coat:
Taubmans UltraProof Acrylic Enamel
General metal steelwork: handrails, bracketing, framing etc.
Gloss options: Gloss, satin, semi gloss, eggshell
Coating type:
Water based premium acrylic finish
Gloss levels: ~
1st coat:
Wattyl Killrust Super Etch
2nd coat:
Wattyl Solagard
3rd coat:
Wattyl Solagard
General metal steelwork: handrails, bracketing, framing etc.
Gloss options: Gloss, low sheen, semi gloss
Coating type:
Water based premium acrylic finish
Gloss levels: ~
1st coat:
Wattyl Killrust Super Etch
2nd coat:
Taubmans SunProof Acrylic
3rd coat:
Taubmans SunProof Acrylic
General metal steelwork: handrails, bracketing, framing etc.
Gloss options: Gloss, satin
Coating type:
Solvent based premium two pack acrylic urethane finish
Gloss levels: Gloss
1st coat:
Wattyl Killrust Super Etch
2nd coat:
Wattyl Poly U 400
3rd coat:
Wattyl Poly U 400
General metal steelwork: handrails, bracketing, framing etc.
1. This information is provided with respect to the listed Valspar products. Valspar recommends that:
(a) The user should check the date of printing, and if more than 24 months have elapsed, should verify with our nearest sales office that the information is still current. (b) you review the Technical Data Sheets (TDS) and Material Safety
Data Sheets (MSDS) before you use or handle the product; (c) the product be used only in accordance with the information provided by Valspar; (d) the product be transported, stored and handled in accordance with the information on
the MSDS and relevant TDS; and (e) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product.
2. The information in this technical data sheet was prepared using information gathered during product development. While Valspar endeavours to update this information and maintain the accuracy and currency of its contents, Valspar
cannot guarantee that the information provided is wholly comprehensive.
3. Valspar recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product.
If you require further information please contact your nearest Valspar Office.
4. Because we cannot control the way these products may be used, or the conditions they may be exposed to, we can give no express guarantees in respect of these products or their performance. However certain guarantees may be
implied by law.
Version 1.0
Reason for issue: New Issue
Issued on: October 2013
Valspar Paint (NZ) Ltd, PO Box 1545, Shortland St, Auckland 1140. Phone 09 820 6700 Fax 09 820 6572
Paintworks Specification 6711W - Exterior new miscellaneous substrates
Page 2 of 2
Coating type:
Solvent based premium two pack acrylic IFC (Isocyante Free Coating) finish
Gloss levels: Gloss
1st coat:
Wattyl Killrust Super Etch
2nd coat:
Wattyl Paracryl IFC 540
3rd coat:
Wattyl Paracryl IFC 540
General metal steelwork: handrails, bracketing, framing etc.
Caution
Refer to Valspar Paints (NZ) Ltd, should full specifications be required, as this format is for use only in CIL
Masterspec formatted documents/specifications.
As for all coatings, provide adequate ventilation during use.
Application should not be carried out if the air or substrate temperature is below 10°C or above 35°C, or the
humidity is greater than 80%. The temperature must not fall below 10°C during the drying process.
Note
1 or 2 coats of primer are recommended depending on anticipated atmospheric conditions. Contact Valspar
Paint (NZ) Ltd Technical Services for advice where extended corrosion protection is required. Refer to
AS/NZS 2312 and 6745W WATTYL PROTECTIVE COATINGS - STEELWORK for more detail regarding the
protection of these substrates from atmospheric corrosion.
1. This information is provided with respect to the listed Valspar products. Valspar recommends that:
(a) The user should check the date of printing, and if more than 24 months have elapsed, should verify with our nearest sales office that the information is still current. (b) you review the Technical Data Sheets (TDS) and Material Safety
Data Sheets (MSDS) before you use or handle the product; (c) the product be used only in accordance with the information provided by Valspar; (d) the product be transported, stored and handled in accordance with the information on
the MSDS and relevant TDS; and (e) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product.
2. The information in this technical data sheet was prepared using information gathered during product development. While Valspar endeavours to update this information and maintain the accuracy and currency of its contents, Valspar
cannot guarantee that the information provided is wholly comprehensive.
3. Valspar recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling the product.
If you require further information please contact your nearest Valspar Office.
4. Because we cannot control the way these products may be used, or the conditions they may be exposed to, we can give no express guarantees in respect of these products or their performance. However certain guarantees may be
implied by law.
Version 1.0
Reason for issue: New Issue
Issued on: October 2013
Valspar Paint (NZ) Ltd, PO Box 1545, Shortland St, Auckland 1140. Phone 09 820 6700 Fax 09 820 6572