GT Products, Inc.
MATERIAL SAFETY DATA SHEET
GT Products XE-6448
PRODUCT
1.
PRODUCT AND COMPANY IDENTIFICATION
Manufactured by:
GT Products, Inc.
501 Industrial Blvd.
Grapevine, TX 76051
Telephone: (817) 481-7113
Fax: (817) 421-1211
Date prepared: 1/23/12
Chemical Type /Description:
2.
By: VLF
Elastomeric Emulsion
HAZARDOUS INGREDIENTS
Component
Hydroxypropylmethylcellulose
Titanium Dioxide
Approximate %
0-2%
0-1%
TLV/PEL
10 mg/m3 (dust)
10 mg/m3 (dust)
CAS Number
9004-65-3
13463-67-7
This product contains Methylpolysiloxanes, which can generate Formaldehyde at approximately 300F (150C) and
above, in atmospheres which contain oxygen. Formaldehyde is a skin, eye, and throat irritant, is toxic and a
potential cancer hazard.
HMIS RATING:
3.
FLAMMABILITY: 1
Very low toxicity expected, a likely laxative.
None expected.
None expected due to very low vapor pressure.
May irritate.
FIRST AID MEASURES
Ingestion:
Skin:
Eyes:
Inhalation:
Other:
5.
HEALTH: 1
EFFECTS OF EXPOSURE
Potential Health Effects:
Ingestion:
Skin Contact:
Inhalation:
Eye Contact:
4.
REACTIVITY: 0
Seek medical attention if adverse symptoms noted.
Remove with dry towel, then wash with soap and water.
Rinse 15 minutes with running water. Seek medical attention if
irritation persists.
Seek fresh air if needed.
Not applicable.
FIRE FIGHTING INFORMATION
Flash Point (Method):
Flammability Class:
XE-6448
>205 F
None
printed: 2/18/2016
page 1 of 3
GT Products
Flammability Limits in Air:
Extinguishing Media:
Hazardous Combustion Products
Special Fire Fighting Notes:
6.
Not available.
All standard media for chemical fires.
CO, CO2, SiO2, H2CO
Like all silicones, GT Products XE-6448 can produce formaldehyde
when strongly heated in air.
ACCIDENTAL RELEASE MEASURES
Pick up spilled material with absorbent clay, then wash area thoroughly with water and detergent. Spilled
material is very slippery.
7.
HANDLING AND STORAGE
Handling:
Storage:
8.
Avoid contact with eyes and prolonged skin contact.
Store in cool (<40C) closed and dry containers. Keep from freezing.
EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Controls:
Personal Protective Equipment
Eyes:
Skin:
Inhalation:
9.
Flowable liquid.
White
Slight
No data available
There is negligible vapor pressure.
0.98
Miscible.
STABILITY AND REACTIVITY
Chemical Stability:
Hazardous Polymerization:
Decomposition Products:
Materials to Avoid:
Conditions to Avoid:
11.
Safety glasses.
Rubber or plastic gloves as desired.
Not normally required.
PHYSICAL AND CHEMICAL PROPERTIES
Physical State:
Color:
Odor:
Boiling Point:
Vapor Density (air = 1):
Specific Gravity:
Solubility in Water:
10.
Good general ventilation.
Stable.
Will not occur.
Only in fire conditions, see section 5.
Acids, bases, oxidizing agents.
None – keep tightly sealed to avoid contamination.
TOXICOLOGICAL INFORMATION
See section 3.
XE-6448
printed: 2/18/2016
page 2 of 3
GT Products
12.
ECOLOGICAL INFORMATION
None available.
13.
DISPOSAL CONSIDERATIONS
Disposal should be made in accordance with state and local regulations. The preferred method is to cure
material and discard the cured rubber in a sanitary landfill.
14.
TRANSPORT INFORMATION
DOT SHIPPING NAME:
DOT HAZARD CLASS:
UN/NA Number:
15.
REGULATORY INFORMATION
TSCA INVENTORY STATUS:
SARA TITLE III / CERCLA
SECTION 302 EXTREMELY TOXIC:
SECTION 304 CERCLA HAZARD:
SECTION 311 / 312 HAZARD
CLASS:
SECTION 313 TOXIC CHEMICALS:
16.
Not regulated.
None.
None.
Listed.
None.
None.
None.
None.
OTHER INFORMATION
We believe the above information is correct as of the date of this data sheet. However, as this information and
the conditions under which the product are used are beyond the control of GT PRODUCTS, INC., it is the user's
obligation to determine the conditions for the safe use of the product. No warranty, expressed or implied, is
hereby made.
XE-6448
printed: 2/18/2016
page 3 of 3