Standard Expel Channel Chunck`s

advertisement
1
FP254
SAFTEY DATA SHEET
Standard Expel Channel Chunck’s
Revision Date 31st January 2013
1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND OF THE
COMPANY / UNDERTAKING
Product Name
Standard Expel Channel Chunck’s
Synonyms, Trade Name
Urinal & Channel Blocks
Application
Washroom
Supplier
Prime Industries Limited,
Unit 2 Broughton Way,
Halebank Industrial Estate,
Widnes,
WA8 8YX.
PHONE 0151 423 0110
FAX 0151 423 0770
[email protected]
Emergency Contact Number
0151 423 0110
SDS No.
C2/464
2. HAZARDS IDENTIFICATION
Irritating to eyes & skin
Classification
Xi; R36/38
3. COMPOSITION / INFORMATION ON INGREDIENTS
NAME
EC No.
CAS-No.
Classification
Conc
Benzenesulphonic Acid Mono C10-14
Alkyl Derivs, Sodium Salts
285-600-2
85117-50-6
Xn;R22 Xi;R38, R41
>30%
Fragrance
N/a
N/a
Xn; R43 R65. N;R51/53
<5%
The Full Text For all R- Phrases Are Displayed in Section 16
4. FIRST-AID MEASURES
Inhalation
Ingestion
Skin Contact
Eye Contact
No hazard with normal use. Remove to fresh air. Keep warm and at rest. Seek medical advice if discomfort
persists.
Possible gastro-intestinal irritation with nausea and vomiting plus irritation of mouth & throat. Immediately
rinse mouth and drink plenty of water. Seek medical advice. Do Not Give Water to An Unconscious person
May cause irritation to skin. Remove affected clothing. Wash affected area with plenty of water and soap.
Seek medical attention if discomfort persists.
May cause irritation to eyes. Wash eyes immediately with plenty of water for at least fifteen minutes
holding eye open. If discomfort persists, seek medical attention.
Page 1 of 3
2
FP254
5. FIRE-FIGHTING MEASURES
Extinguishing Media Use:
Unusual Fire & Explosion Hazards
Use extinguishing media appropriate to the surrounding conditions
None
Specific Hazard
Burning produces irritating toxic and obnoxious fumes
Protective Measures in Fire
Self contained breathing apperatus and ful protective clothing must be worn in case of fire.
6. ACCIDENTAL RELEASE MEASURES
Personal Precautions
Ensure adequate ventilation of the working area, do not breath dust. Avoid contact with skin and
eyes.
The material is designed for Washroom use and normal safe disposal to foul sewer. In the event of a
spillage of a large amount of product, entry to surface water drainage should be avoided. Major
spillage losses to surface drainage must be notified to the local waste authority
Contain and collect spillage. Sweep up and transfer into suitable containers. Dispose of in accordance
with local waste authority
Environmental Precautions
Spill Cleanup Methods
7. HANDLING AND STORAGE
Usage Precautions
Fire & Explosion
Storage Precautions
Avoid skin and eye contact. Ensure adequate ventilation of the working area. Avoid breathing dust. Wash
properly with soap and water. Adopt best manual handling consideration when handling, carrying and
dispensing.
No special measures
Store in a cool dry area. External damage to containers should be avoided. Seal containers after use. Use in a
well ventilated area. Do not store product in direct sunlight. Oxidiser storage
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Protective Equipment
Engineering Measures
Ensure Adequate ventilation of working area
Respiratory Equipment
Not required under normal use
Hand Protection
Eye Protection
Other Protection
Wear suitable gloves
Wear approved safety goggles
Wear suitable protective clothing to prevent skin contact
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Approximately 25mm round block
Colour
Blue or Yellow
Odour
Pleasant
Solubility
Freely in water
pH
~8 (1% Solution)
10. STABILITY AND REACTIVITY
Stability
Conditions To Avoid
Materials To Avoid
Hazardous Decomposition Products
A stable product in normal temperature conditions and recommended use
Avoid excessive heat for long periods of time
Strong acids
Halogenated hydrocarbons. Hydrogen chloride (HCI). Oxides of: Carbon, Sulphur
11. TOXICOLOGICAL INFORMATION
Inhalation
Irritating to respiratory system
Page 2 of 3
3
FP254
Ingestion
Harmful if swallowed
Skin Contact
There may be mild irritation and redness at the site of contact. Possible development of sensitivity
Eye Contact
May cause eye irritation, redness and blurred vision
12. ECOLOGICAL INFORMATION
Ecotoxicity
Mobility
Degradability
The product components are not classified as environmentally hazardous.
The product is soluble in water
The product is biodegradable
13. DISPOSAL CONSIDERATIONS
General Information
Disposal Methods
Do not wash into surface water drains. Do not mix with other waste materials. Wear appropriate clothing,
goggles and mask
Arrange disposal as special waste by licensed disposal company, in consultation with local waste disposal
authority, in accordance with control of pollution Act 1974
14. TRANSPORT INFORMATION
Not classified as “Hazardous for Transport”
15. REGULATORY INFORMATION
Labelling
Contains
Risk Phrases
Safety Phrases
Irritant
Benzenesulphonic Acid Mono C10-14
Alkyl Derivs, Sodium Salts
R36/38 – Irritating to eyes & skin
S2 –Keep out of reach of children.
S24/25 – Avoid contact with eyes & skin.
S26 – In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S28 – After contact with skin, wash immediately with plenty of water.
S37/ 39 – Wear suitable gloves and eye/face protection.
S46 – If swallowed, seek medical advice immediately and show container or label.
16. OTHER INFORMATION
Approved Code of Practice
Guidance Notes
REV. No. / REPL. SDS
Generated
SDS No.
Safety Data Sheet Status
Approved.
Signature
Risk Phrases in Full
Notes
Safety data sheets of substances and preparations. Classification and labelling of substances and
preparations dangerous to supply
CHIP for everyone HSG (108). Workplace Exposure Limits EH40
31st January 2013
C2/464
31st January 2013
R22 – Harmful if swallowed.
R38 – Irritating to skin.
R 41 – Risk of serious damage to eyes.
R43 – May cause sensitization by skin contact.
R65 – Harmful: may cause lung damage if swallowed.
R51/53 – Toxic to aquatic organisms, may cause long term adverse effects in the aquatic environment.
This information relates only to the specific material designed and may not be valid for such material
used in combination with any other materials or in any process. Such information is to the best of the
company’s knowledge and belief, accurate and reliable as of date indicated. However, no warranty,
guarantee or representation is made as to its accuracy, reliability or completeness. It is the user’s
responsibility to satisfy himself as to the suitability of such information for his own particular use.
Page 3 of 3
Download