Teledyne Monitor Labs is a leading supplier of environmental monitoring
instrumentation, systems and software.
APPLICATION/SETUP INFORMATION FOR SM425 OXYGEN (O2) ANALYZER
1.
CUSTOMER CONTACT INFORMATION
*Name:
*Date:
(TML Use Only)
Title:
RFQ:
*Company:
Quote:
*Phone:
P.O.:
FAX:
TML Order:
Email:
*Plant Site:
*Site Address:
*Plant Contact:
*Stack Identification:
2.
Limited to 10 characters
APPLICATION
A. Function (Select One of the Following)
B. Compliance Monitoring
(Provide Details)
Federal (Specify):
State (Specify):
42500006, REV C
Revision Date 9/15
1
3.
PLANT CHARACTERISTICS (Provide Details)
*Combustion Source/Process (Specify): Utility Boiler - Coal
*Fuel(s) (Specify):
*Particulate Controls (Specify, If No Particulate Controls, State If Excessive Particulate Condition):
*NOX Controls (Specify):
*Flue Gas Desulfurization (Specify):
*Elevation Above Sea Level (Specify):
*Unusual Conditions (Specify):
4.
SM425 EQUIPMENT INTERFACE REQUIREMENTS
A. TML DAS, SM8XXX Analyzer
(Select One of the Following & Provide Details)
Model (Specify):
B. Other Data Recording Systems
(Select One of the Following & Provide Details)
Model (Specify):
C. 4-20 mA Analog Signals (Select One of the Following & Provide Details that
Include the Number of Analog Signals Needed)
D. Relay Contact Signals (Select One of the Following & Provide Details that Include
the Number of Discrete I/O Needed)
42500006, REV C
Revision Date 9/15
2
5.
INSTRUMENT AIR AVAILABILITY
A. A Pollutant Free, Particulate Free, Oil-Free, Dry Air with -4°F (-20°C) Dew
Point (Select One of the Following)
B. 30 to 50 PSIG (207 to 345 KPA) Pressure
C. 1 LPM Flow Capability
(Select One of the Following)
D. Instrument Air to be Used as Calibration Air
6.
(Select One of the Following)
(Select One of the Following)
ELECTRICAL POWER (Select One of the Following & Provide Details. Power
Requirements are 100-240VAC, 300W, 45-66Hz, Single Phase)
*Voltage (Specify):
*Amps (Specify):
*Frequency (Specify):
7.
PROBE INSTALLATION AND OPERATING CONDITIONS
A. Site
(Select All that apply from the Following & Provide Details)
Duct
Stack
Double Wall
Insulated
42500006, REV C
Revision Date 9/15
3
*Inner Diameter (Specify):
*Outer Diameter (Specify in Inches):
*Structure Material (Specify):
B. Access Port Mounting Flange
(Select One of the Following)
C. Flange Orientation (Select One of the Following)
D. Stack or Duct Environment (Select One of the Following)
E. Gas Conditions
(Provide Details)
Nominal
High
Low
O2 (%)
Ambient Temp (°F or °C)
Stack Gas Temp (°F or °C)
Stack Gas Velocity
(Ft/Sec or m/Sec)
Stack Gas Pressure
(In. of H2O or mm of Hg)
Dew Point (°F or °C)
Particulate Loading
(Grains/SCF or mg/SCM)
42500006, REV C
Revision Date 9/15
4
F. Unusual Requirements
(Select All that Apply from the Following)
Excessive Vibration
Measurement Cavity Less than 3.28 Feet (1 Meter) from the Duct or Stack Inner Wall
Entrained Water in Measurement Stream
Large and/or Fast Changes in Stack Temperature and/or Pressure
Other (Specify):
G. Installation Description
(Provide Details)
General Description of
Planned Installation:
Describe Special
Requirements for the
SM425:
Describe Special
Requirements for the Site:
DO NOT WRITE IN THIS
SPACE
Approval:
Application Engineer
FOR TML USE
ONLY
Date:
*Please forward Checklist to your Regional Teledyne Monitor Labs Sales Manager *
Or
Email: TML_Sales@Teledyne.com
42500006, REV C
Revision Date 9/15
5