MATERIAL SAFETY DATA SHEET
Product Name:
Date:
Spray Wash 100
2/04/2010
1. Product and Company Identification
Product Name
Spray Wash 100
COMPANY IDENTIFICATION
Curtis Fluids
1901 Godfrey Ave., SW
Grand Rapids, MI 49509
Customer Service/Emergency
616-452-5797
2. Hazards Identification
This product contains 2-Butoxyethanol, a toxic chemical subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right to Know Act & of 40 CFR 372.This product is not considered a hazardous
material by the U.S Department of Transportation.
3. Composition Information
Hazardous Components:
Name
CAS
Weight
Labeling
2-Butoxyethanol
111-76-2
25ppm
R20/21/22 R36/38
4. First-aid Measures
Inhalation: Remove to fresh air. If breathing is difficult, have trained person administer oxygen. Get medical attention
immediately.
Eyes: Immediately flush with direct stream of water for at least 15 minutes holding the eyelid apart to ensure
complete irrigation of the eye.
Skin: Flush thoroughly with cool water under shower while removing contaminated clothing. Wash clothing before
reuse.
Ingestion: Never give anything by mouth to an unconscious person. Do not induce vomiting. Give large quantities of
water. Get medical attention immediately.
5. Fire Fighting Measures
Extinguishing Method/Media: Not combustible. Water spray, dry chemical, CO2 or foam may be used in areas
where product is stored.
Special Fire Fighting Procedures: Product presents no unusual fire hazard and requires no special procedures.
Unusual Fire and Explosion Hazards: None known.
6. Accidental Release Measures
Steps to be taken in case material is released or spilled: If spilled, steps should be taken to contain spill. Clean
areas of spill immediately.
7. Handling and Storage
Handling/Hygienic Data: Wear safety goggles and protective gloves.
Storage: Store in original container in a cool and dry area. Protect from freezing.
8. Exposure Controls / Personal Protection
Personal Protection: Eyes: Goggles required. Ingestion: Avoid ingestion. Respiratory: General ventilation. Skin:
None.
9. Physical and Chemical Properties
Appearance and Odor:
Solubility in water:
Specific Gravity:
Vapor Density:
Vapor Pressure:
Yellow liquid with Characteristic odor.
100%.
(H2o = 1.0) Not Determined
(Air=1) Not Determined
Not Determined
10. Stability and Reactivity
Conditions to Avoid:
Contact with heat, strong alkalis, strong oxidizing agents.
Stability:
Stable.
Incompatibility:
Strong acids
Hazardous Polymerization:
Will not occur
Hazardous Decomposition or Byproducts:None
11. Toxicological Information
Oral:
Dermal:
Inhalation:
Ocular:
None known for blend.
None known for blend.
None known for blend.
None known for blend.
12. Ecological Information
There is limited information available on the environmental fate and effects of this material. It is miscible in water. Due
caution should be exercised to prevent the accidental release of this material to the environment. In concentrated
form this product may show trace levels of toxicity to aquatic organisms.
13. Disposal Considerations
Dispose of all waste and contaminated equipment in accordance with all applicable federal, state, local health and
environmental regulations
14. Transport Information
This product is not regulated. DOT class 55.
15. Regulatory Information
SARA/TITLE III HAZARD CATEGORIES: If the word “yes” appears next to any category, this product
may be reported by you under the requirements of 40 CFR 370. Please consult those regulations for
details. Immediate (Acute) Health: Yes Delayed (Chronic) Health: No Fire Hazard: No Reactivity Hazard:
No Sudden Release of Pressure: No
HMIS HAZARD RATINGS: Health Hazard: 1
Fire Hazard: 0
Reactivity: 0
INTERNATIONAL REGULATIONS: Consult the regulations of the importing country.
16. Other Information
Raw material suppliers’ data sheets were used as key data
sources in the preparation of this material safety data sheet.
Sources of key data used:
R Phrases:
R20/21/22:
Harmful by inhalation, in contact with skin and
if swallowed.
R36/38:
Irritating to eyes and skin.
This information is provided is accurate to the extent of our capabilities to ascertain. It is current. We
advise the user to make his our evaluation and determinations as to whether circumstances of usage,
application of product, and disposal are safe and meet governing agency requirements. Curtis Fluids
makes no guarantees or warrantees other than replacement.