COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
1.CHASSIS
1-1- ENGINE
Diesel engine 4 stroke , water cooled, direct injection turbo charger
with best safety tools and compatible with Jordan diesel fuel ,not less
than 280 HP.
High speed control limit (not exceed 80km/hr).
Exhaust gas pollution emission in the atmosphere shall comply with
Min. Euro 2 / Euro 3 or equivalent regulation.
1-2- PAY LOAD
Weight of (Body compactor + pin lifter+3 person (3x85kg)+
Waste with density (600kg/m3)+fuel).
1-3- CLUTCH:
Dry plate.
1-4- GEARBOX
Automatic or Manual transmission all synchromesh not less than 6
speeds + one reverse , provided with power take off operation from
driver cab.
1-5- STEERING :
L.H.D Power Steering
1-6- BRAKES
(ABS or any high brake safety system) parking brake
exhaust brake
1-7- TIRES
Single front, dual rear same size available in the
local market spare wheel and tire with carrier. the tire
should be manufactured the same year of truck, (on/ off )
road
1-8- CAB
Three passengers (2+driver) ALL welded steel cab of tilt type,
provided with Air condition , heater , ventilator and defroster.
Adjustable driver , seat lockable doors. Not less than two side
mirrors, two wipers and washers, floor mats , panel includes KM
speedometer and tachograph in addition to standard gauges and
controls. RPM gauge , seats belts ,AM/FM radio
COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
2.BODY AND
2.1 Net capacity 15m3 (without hopper capacity).
COMPACTION
2.2. Hopper floor made from hardox or equivalent high tensile
SYSTEM
steel sheet of thickness not less than 8 mm and side panel not less
than 6 mm thickness.
2.3 Press panel made from hardox of high tensile steel sheet not
less than 6 mm thickness.
2.4 Foldable footboards built in anti-skidding plate.
2.5 Sewage water relieve to suitable volume tank under tail gate
with leak proof discharging outlet.
2.6 Dimension and thickness of material (body side roof, floor,
tailgate sides and floor) should be compatible with the
required compaction ratio using high corrosion resistance
material.
2.7 Compaction ratio not less than 5:1.
2.8 Work cycle time (30-35) seconds.
2.9 Hopper capacity approximately 1.4m3.
2.10 Painting : Sand Blasting:
2.10.1 One coat of anti – corrosion primer.
2.10.2 At least two coats paint.
2.11 Rear camera connected to cabinet screen device and
movement safety.
2.12 Self-lubricating system
3.HYDRAULIC
AND
ELECTRICAL
SYSTEM
3.1 Full automatic control integrated with lifting device (one
button bush).
3.2 Safety hard and soft ware for :
COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
3.2.1 Avoiding any solid bodies damage slide plate.
3.2.2 Two hydraulic cylinders for lifting / lowering tailgate.
3.2.3 Provided with load devise for stop compactors when
load approach 8 ton.
3.2.4 Lifting and tipping device type with two folding arms and frame.
3.2.5
Over weight limit (bin, compactor).
3.2.6
Hydraulic oil over heat safety limit.
3.2.7
Low hydraulic oil level (safety switch off).
3.2.8
Oil filtering (cartridge & magnetic).
3.2.9
High quality of all hydraulic components .
3.2.10 All hydraulic system should be equipped with high
level of safety protection.
3.3 (12-24)-volt electric system, starter, alternator, batteries in
series headlights instruments …etc system , 2 beacon .
3.4 Separate manual control of the packer and carriage plate
functions.
4.GRADEABILITY
4.1-Not less than 35 % with full load during using lifting
device (stop/startup).
5.LIFTING
SYSTEM
5.1 High capacity articulated arm lifting device works in min. two
stages by four double effects hydraulic cylinders to ensure
lifting and lowering of containers smoothly.
5.2 Can lift standard 120/240/770 and 1100 liter containers.
5.3 Lifting weight capacity not less than 800 kg.
COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
6.ACCESSORIES
6.1 Service manual and spare parts catalogue. For each unit.
6.2 Years of Manufacture: (2012 ) for both chassis and
compactor, brand new products.
6.3 Complete tool kit for maintenance, fire extinguisher ( 10kg )
6.4 Hydraulic jack 10 ton .
6.5 Attached spare parts list, priced individually.
6.6 COLOR: Orange / White.
6.7 All specification must be highlighted on catalogue when
submitting the bid offer
7.TRAINING
7.1 Technical training course for three technical employer in
manufactory country after final receiving
8.1 GENERAL
Required Brand new vehicles model (2012 ) will be
used in Jordan and should be suitable with high
performance in all Jordanian geographic areas and at all
weather conditions as example:
8.1.1
Temperature range : from -10 C to + 50 C
8.1.2
Altitude : from (-400) meter (below sea level)
up to (+1200) meter (above sea level), humid
in some areas and dry in others, dusty weather ,
desert , and cloudy weather are available.
8.1.3
Roads : Asphalt highways between cities ,
climbing and descending mountain's roads.
8.1.3.1 Secondary asphalt narrow roads between towns
and villages, second and 3'rd class quality.
8.1.3.2 Agricultural un asphalted roads between small
villages.
8.1.4
Duration of daily job: Between 16 to 24 hours,
COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
i.e. (two – three) shifts.
8.1.5
Type of refuse : All types: solid, soft, dry,
damped, heavy and light refuse (not separated
refuse) …etc.
8.1.6
Required vehicles shall comply all Jordanian
traffic regulations and laws as examples:
8.1.6.1 Max. axle loads – front and Rear – single and
dual tires.
8.1.6.2 Max. width, height and length.
8.1.6.3 All lights, signals, wind shields, mud flaps,
reverse alarm, horn, mirror and sun
visors….etc.
8.1.6.4 Left hand drive.
8.1.6.5 Drivers tools and extinguisher.
8.1.6.6 License plate front and rear.
8.1.7
A prices list of spare parts would be required for
three years of operation.
8.1.8
Bidder shall specify all required information of
conditions and of specification with limited and
clear information one by one consequently and
respectively.
8.1.9
Warranty against any defect caused by
manufacturing reasons for all the vehicle including
chassis and refuse (compactor), lifting and lowering
device, and all other components a warranty for the
tires, batteries as provided by manufacturer.
8.1.10 The required vehicles should be subjected to actual
real run test at site before the final report of receipt.
8.1.11 Bidder shall submit a certificate from the
(compactor's) manufacturer or agent, stating that the
COMPLY SHEET
GARBAGE COMPACTOR TRUCK
GARBAGE TRUCK ( COMPACTOR TYPE )
VOLUME 15M3
QUANTITY REQUIRED (30)
Manufacturing year ( 2012)
manufacturer has no objection concerning installing
his (compactor) on the Chassis provided by the
bidder without any reservation . Also Bidder shall
submit a certificate from the chassis' Manufacturer
or agent, stating that the Manufacturer has no
objection concerning installing the (compactors) on
his chassis provided by bidder without any
reservation.
8.9
Inspections:
8.9.1 Third party Inspection:
Supplier Shall arrange with recognized 3rd party inspection body
before shipping in the country of origin for both chassis and
(compactors), cost shall be born by the supplier.
8.9.2 Maximum three persons from the owner side have to
witness the testing and inspection process for the production.
8.9.3
Final inspection : (Final Acceptance):
The Technical Committee assigned by owner will examine the
(garbage truck) against the Technical Specifications, fuel
consumption, and Contract Documents.
‫جهاز خلفي) و تشمل جميع قطع‬+‫الكفالة لمدة ثالثة سنوات لأللية كاملة(شاصي‬
‫ على ان يتم‬، ‫الغيار المستهلكة من بريك و كالتش وغيار زيت وفالتر مجانا ً وأجور‬
‫تقديم القطع المستهلكة جميعها في العرض المقدم من الشركة و حسب كتالوجات‬
‫) ساعة‬16( ‫الشركة الصانعة للجهاز و الشاصي و على اساس اعتماد عمل اآللية‬
.‫ الكاوتشوك و البطاريات حسب توصيات الشركة الصانعة‬،‫يوميا‬