Summary of Features:
• New!
V-SLICE
TM
Cutter Technology
•
Unique, One-piece Cast Motor Housing
• Epoxy Powder Coated
• Improved Flow, Open Volute Design
•
Heavy-duty, High-torque Motor
•
Solid State Starting Circuit
•
Quick-disconnect Power Cord
• Dual Shaft Seals
• Panel-less Design (single phase)
•
Piggy-back style plug connection (single phase)
•
Stainless Steel Impeller
Patent Pending

TM
Macerates and shreds jeans, shop rags, sanitary napkins, diapers…
Rotary cutter and plate all made from
440 stainless steel, hardened to Rockwell
58c
Exclusion slots – clear debris from behind rotary cutter
Recessed nut helps eliminate “wadding”
Unique V-SLICE
“alternating cut” design for improved shredding over single “round-hole” designs.

Stainless steel clasp for lift-out chain
Solid one-piece cast iron housing
Solid-state starting circuit
Upper and lower ball bearings
High-torque 2 hp. motor
Upper seal – Silicon
Carbide, unitized
Lower seal – Viton doublelip
Improved-flow volute with no cutwater. Helps reduce clogging.
Beefy stainless steel handle with rubber Grip
Quick-disconnect cord design
Internal capacitor – eliminates expensive control panels
Wide-angle switch with piggy-back style plug
300-Series stainless steel rotor shaft
300-Series stainless steel impeller
Hardened stainless steel cutter plate with spiral clean-out
Hardened stainless steel rotary cutter

LSG202
U.S. Gallons Per Minute

Omnivore Curve
Example of pump with a minimum head requirement
Minimum operating head 30’
DANGER ZONE
Operating below the required minimum head can overload the motor causing product failure!
Many grinders have a
“minimum head” requirement.
What if you have a lowerhead application?
TM is engineered to run efficiently at low heads!
Even downhill
“negative head” pumping is not a problem for the
OMNIVORE!

Typical components of a pre-designed system from
Liberty Pumps
Discharge
Pipe
Waterproof
Wiring Box
Alarm
Guide rail system for easy lift out of pump
GR20 disconnect and guide-rail base with ball check valve.
Simplex or Duplex
Panels
4” inlet hub
QuickTREE
TM
Adjustable float system allows easy removal of floats for cleaning and service without entering pit.

Integrated ball
Check valve
•
Cast Iron Construction
• Integrated ball check valve
• Simple one rail design
• Auto-position feature assures
• proper locating
Upper mount for guide rail pipe
Pump during liftout “unlocked” Pump in “locked” position

LSG202-RE
Retro-Fit System for
E/One® Grinder
Packages
A completely assembled grinder replacement package for E/One® GP 200 and GP 2000 systems.
•
Liberty's 2 hp Omnivore Grinder Pump
• Assembled and ready to drop-in-place
• Includes floats, piping, and replacement cover
• Heavy-duty cast iron anti-siphon check valve
• Weatherproof Junction Box
E/One® is a registered trademark of Environment One
Corporation and is not affiliated with Liberty Pumps.

LSG202-RE
7 ft Drop rope
Discharge elbow fits E/One® receptacle / valve
Water proof enclosure for splicing existing wires
Weighted high water alarm float
Cast Iron
Anti-siphon check Valve
LSG202A
Grinder Pump
*E/One is a registered trademark of Environment One
Corporation and is not affiliated with Liberty Pumps.
E/One® System

Note: * E/One® Series GP200 and GP2000 pumps are of the progressive cavity design that have the capability to develop higher pressure than centrifugal style grinders, While the LSG202-RE Retro-Fit from Liberty will work in many applications as a direct dropin replacement for E/One®, some installations may exceed the head or pressure capabilities of the LSG202-RE.
*E/One is a registered trademark of Environment
One Corporation and is not affiliated with Liberty Pumps.
E/One Curve
Omnivore Curve

Liberty offers a wide range of factory predesigned simplex and duplex systems featuring the Omnivore grinder.
Diameter Height
2448LSG
24
24” 48”
• When you specify a Liberty pre-designed system, you know it is right - the first time.
• Total custom systems are available - consult our technical sales department at 1-800-543-2550!

End.