1
Enabling Wellbeing
Halton - Enabling Wellbeing




Halton was established in 1969
Family owned company, operating in 23 countries.
We are passionate about indoor environments.
We offer business enhancing products, systems, and services for
comfortable, energy efficient, and safe environments.
.
Enabling Wellbeing
Strategic Business Areas
•
•
•
•
•
Halton Foodservice: Inspiring kitchen environments
Halton Indoors: Makes work a breeze
Halton Marine: Safe and seaworthy
Halton Clean Air: A clean advantage
Halton New Ventures: Ensuring wellbeing
Enabling Wellbeing
Halton’s Duct Monitoring and
Safety System - KGS
KGS – Kitchen Grease Sensor
Halton Strategy for High Performance Kitchen
Capture Jet technology
Capture Jet hoods and ceilings
Energy
efficiency
Capture Ray technology
Show kitchen solutions
Fire suppression
IEQ
Ecology Units
HPK
Air
purification
Low velocity supply
Water Wash technology
KSA Filters
KGS – Kitchen Grease Sensor
Safety
F.O.R.M.
M.A.R.V.E.L.
Grease Sensor
KDS Systems
System Layouts
KGS – Kitchen Grease Sensor
6
What is the Duct Monitoring and Safety System (KGS)?
•
•
•
•
•
A signaling device that monitors the grease deposition levels in all
monitored duck work and hood exhaust plenums.
Once the level of grease exceeds the set point threshold an alarm is
displayed on the system console alerting the operator that the
ductwork needs to be cleaned based on NFPA96 guidelines.
Provides an indication whether the cleaning was done satisfactorily.
System consists of one or more panels containing the controls and
a display console; grease sensors located in the exhaust plenum of
a hood and the exhaust ducts.
Compatible for use with new or existing ductwork
KGS – Kitchen Grease Sensor
Listings
Grease Sensor Assembly
• UL710 / ULC S646
• Covers grease penetration in ductwork
• Label will be stamped to the outer surface of the the reflector
KGS Duct Safety Monitoring System
• ETL listed to UL 2017 general purpose signaling device and systems
• Covers system as a whole
• There is no label as each part follows individual certification markings
KGS – Kitchen Grease Sensor
Control Panel – Inside View
KGS – Kitchen Grease Sensor
Grease Sensor in Duct – Outside View
Glass for demonstration
purposes only
KGS – Kitchen Grease Sensor
Grease Sensor in Duct – Inside View
Grease
Sensor
KGS – Kitchen Grease Sensor
Grease Sensor Assembly
KGS – Kitchen Grease Sensor
13
Sensor Access
KGS – Kitchen Grease Sensor
Hex Nut
Grease Sensor
M 18 Internal Tooth Lock
Washer
Reflector
18 mm (45/64”
Hole
Gasket
Hex Nut
Grease Sensor
Duct “by others”
Air Flow
KGS – Kitchen Grease Sensor
To KGS Control Panel –
Maximum 100 feet from
control panel
Grease Sensor Cable Connections
KGS – Kitchen Grease Sensor
Console Interface
Power Light
Sensor Lights
Active Sensor
Button
Active Sensor
Alarm Light
KGS – Kitchen Grease Sensor
Cleaning Due
Button
Cleaning Due
Alarm Light
Connect to
PDA
Button
Connection
Alarm Light
Sensors
Active sensors will remain a steady light when no alarms are active.
KGS – Kitchen Grease Sensor
Active Sensor Alarm Light
If Active Sensor Alarm Light is on, this indicates that there is a problem with an
actual sensor.
KGS – Kitchen Grease Sensor
Cleaning Due
If Cleaning Due Alarm light is solid red, then cleaning is required. Once the
Cleaning Due Button is pressed, all active sensors that require cleaning will
begin to flash green.
KGS – Kitchen Grease Sensor
Master Display Panel
KGS – Kitchen Grease Sensor
Slave Panel
Remote Display Panel
KGS – Kitchen Grease Sensor
Installation
•
From design layout, locate each grease sensor and drill a 18mm hole in the
duct work.
– Location should be in the vertical section of the ductwork. If you have to
put in horizontal sections in the ductwork, avoid the bottom area.
– If access panels are not available, you may need to cut an opening in the
ductwork to accommodate a UL listed access panel
• Locate and position Master Control Panel and the Slave and/or Remote
Display if equipped. Keep in mind that the distance between the sensors
and/or Master/Slave can not exceed 100 ft. The maximum distance
between the Master, Slave, and/or Remote Display Panel is 300 ft.
• Run and connect each grease sensor cable to the panel. Each sensor will
be labeled to match terminal location in panel
• Connect 120V power to the panel
• Test system for power as well as ensuring that each sensor is online
KGS – Kitchen Grease Sensor
System Layouts
KGS – Kitchen Grease Sensor
Duct Monitoring and Safety System for Ecology
KGS – Kitchen Grease Sensor
Service and Maintenance
•
The KGS system should only be cleaned when the entire duct system is
cleaned. Always inspect at cleaning each grease sensor and insure
reflective surface and lens are clean. When cleaning, do not use steel wool
or other abrasive materials that would scratch the reflective material or lens.
•
The KGS system must be inspected after each 12 months of service. To
schedule inspection, contact your authorized service agent or consult the
factory for additional details.
•
The grease sensors have a typical life span of three years. After three
years, the grease sensors must be replaced. For replacements, contact
your authorized service agent or consult the factory for additional details.
KGS – Kitchen Grease Sensor