Handelsweg 20
8152 BN Lemelerveld
Tel.: + 31 (0) 572-371027
Fax: +31 (0) 572-371014
info@epdmsystems.nl
www.epdmsystems.nl
TECHNICAL SPECIFICATION
E 225 Spraybond
(08/2013)
Description:
E 225 spraybond is an industrial grade spray adhesive formulated specifically to bond
panel materials. It is designed for bonding exterior grade substrates to foam. It is a
fast drying formula and has excellent high coverage. It has good moisture and
weather resistance against extreme temperature exposure. The aerosol system
reduces application cost by saving time and material. Supplied in portable ready to
use package. It is a fast drying formula and has excellent high coverage. It has good
moisture and weather resistance against extreme temperature exposure. The aerosol
system reduces application cost by saving time and material.
Features:
High Solids
• High Coverage
• Fast Drying Formula
• Good Moisture Resistance
• High Temperature Resistance to 110°C
• Ready to Use
Designed for bonding exterior grade substrates to foam.
Suggested apllications directions for use
Make sure the surfaces are clean, dry, free from dirt, dust, oil, loose paint, wax or
grease and any other contamination. Substrates should be properly conditioned and
along with the adhesive should be between 16 °C and 27 °C before bonding. Agitate
canister contents before use. Securely attach hose ET12T and spray gun EG1020
(with 9501) tip on to the canister with applicator gun fully locked. Slowly open the
valve on the canister and check for leaks before opening the valve fully. Unscrew the
trigger stop/adjusting nut on the applicator away from the trigger 2-3 turns and
spray a test pattern. For more adhesive output, continue to screw the nut away from
the trigger. Hold spray gun 10cm-25cm away from the surfaces to be covered. Apply
an even coat of adhesive to both of the surfaces to be bonded. You may apply up to
three coats of adhesive depending on the need for coverage and the application.
Always test adhesive on new materials to be bonded to ensure proper bonding and
compatibility of the materials to be bonded. Allow the adhesive to dry until tacky
then make the bond, applying sufficient pressure to ensure complete contact
between the two substrates.
Dry time is approximately 1 - 5 minutes, open time is approximately 5 - 20 minutes
after application depending on environmental conditions.
For Storage, lock the spray gun in the closed position and leave hose attached to the
canister with the canister valve open. If the canister is not to be used for at least a
Pagina 1/2
Handelsweg 20
8152 BN Lemelerveld
Tel.: + 31 (0) 572-371027
Fax: +31 (0) 572-371014
info@epdmsystems.nl
www.epdmsystems.nl
week, it is recommended to close the valve on the canister and spray out any
remaining adhesive and propellant left in the gun and hose until they are completely
empty. Only when no more material or propellant is left in the hose or gun,
disconnect the hose from the canister and connect to a canister of StarStuk ACR
cleaner (sold separately) and spray until the liquid being evacuated from the spray
gun is clear. To disconnect and re-connect the canister repeat the steps above. Clean
the spray tip by pulling away any dried adhesive or soak the tip in StarStuk
ACR cleaner or other solvent until the adhesive softens, then remove. Do not use
foreign objects to clean out the tip or insert a pin or sharp object in to the tip. This
will damage the tip and greatly effect the spray pattern.
Physical properties
Shelf life:
18 Months from date of manufacture.
Storage:
Not damaged by freezing. Return to room temperature prior to use.
For canister products keep cylinders off floor when temperature is
below 15°C.
Appearance
Base
Solvent
Glue % Solids
Gravity
Failure temperature
EU VOC
:
:
:
:
:
:
:
Clear or Blue in colour
Synthetic Polymer
Hydrocarbon
25 – 30% specific
0.72 ± 0.02 g/l
Approximately 110 ºC
85 ± 1%
Packaging
Net Weight 13.6 kg Disposable Canister
E225 SPRAYBOND
An industrial spray grade adhesive formulated to bond panel materials.
DISCLAIMER OF WARRANTY
The technical data contained herein is based on our present knowledge and
experience and we cannot be held liable for any errors, inaccuracies, omissions or
editorial failings that result from technological changes or research between the date
of issue of this document and the date the product is acquired. Before using the
product, the user should carry out any necessary tests in order to ensure that the
product is suitable for the intended application. Moreover, all users should contact
the seller or the manufacturer of the product for additional technical information
concerning its use if they think that the information in their possession needs to be
clarified in any way, whether for normal use or a specific application of our product.
Our guarantee applies within the context of the statutory regulations and provisions
in force, current professional standards and in accordance with the stipulations set
out in our general sales conditions. The information detailed in the present technical
data sheet is given by way of indication and is not exhaustive. The same applies to
any information provided verbally by telephone to any prospective or existing
customer.
Pagina 2/2